LumberJocks

LJTV: LumberJocks Woodworking Videos

  • Advertise with us

This is the list of all blog entries tagged with 'video'.

View Blake Haskins 's profile

repurpose pallet wood and co2 canister coat rack

04-15-2017 03:42 AM by Blake Haskins | 0 comments »

In this video I created a coat hanger from USED co2, however if you decide to hammer an unused one, let me know how that goes. The backer is pallet wood with some sort of red chemical that I refer to as paint, but I didn’t sand it, so I wasn’t worried about breathing it in. I used dry-wall anchor...

Watch this video »

View woodify's profile

Storage Shelving

04-13-2017 11:06 PM by woodify | 0 comments »

I built these two storage shelving units for my basement. They were super easy to build. Check out my video and if you’re looking for the measurements look here.View on YouTube

Watch this video »

View DsRMR's profile

shop re start the new RMR #4: stop water penetration and band saw breakdown

04-13-2017 08:58 AM by DsRMR | 0 comments »

Hello again it’s been slow going in the shop still been darn cold out plus had some water control to get under control. This was the result of poor workmanship of the pole barn that is my shop atm. The perimeter of the buildings ground work was above the bottom of the cur-agate siding, wit...

Watch this video »

View JimDaddyO's profile

Shop stuff #88: Tool Chest Pt 2

04-12-2017 11:30 AM by JimDaddyO | 0 comments »

In this one I get the carcass of the chest finished up and assembled. Turns out bigger than I thought, and that is a good thing. View on YouTube

Watch this video »

View PeteCollin's profile

Milling a Walnut Log with Matthias Wandel's Big Bandsaw

04-09-2017 08:46 PM by PeteCollin | 1 comment »

Hello All,On a nice spring day I played around in the barn. https://www.youtube.com/watch?v=FLPxO9zriVA

Watch this video »

View A Slice of Wood Workshop's profile

Cheese Board and Hand Forged Slicer | Pt 2

04-09-2017 02:33 PM by A Slice of Wood Workshop | 0 comments »

In this video I finish all the detail work of the cheese board. Using hand planes I get everything flattened. Then using a router table I rounded all the edges over and also cut a radius on all the corners. I wanted a way to hang this and drilled a 1 3/8” hole in the corner of the board. Ne...

Watch this video »

View Blake Haskins 's profile

coolest homemade fidget spinner

04-09-2017 11:26 AM by Blake Haskins | 0 comments »

I know its not woodworking, but I have seen a ton of woodworkers make one.I put this link because I am proud of the video and the result.Enjoy- https://youtu.be/fs93RtggUFA

Watch this video »

View A Slice of Wood Workshop's profile

Cheese Board and Hand Forged Slicer | Pt 1

04-08-2017 11:40 PM by A Slice of Wood Workshop | 0 comments »

I wanted to create a cheese board, but didn’t want it to be “normal”. I wanted to give it an extra touch and decided that I would hand forge a slicer for it. In this video I got everything roughed out and glued up. Hand forged slicer will be out 4-9-17. Subscribe to see all the ...

Watch this video »

View A Slice of Wood Workshop's profile

Restore Those Rasps and Files

04-08-2017 12:49 AM by A Slice of Wood Workshop | 0 comments »

You can find rasps and files very cheap. Usually they are rusty and dull. With a bit of time and some acid you can easily restore those files and rasps. After that, make some very comfortable handles. Check out the video here and hit that subscribe button.

Watch this video »

View woodify's profile

Winner Announcement - Makers Rock Album Art

04-08-2017 12:01 AM by woodify | 0 comments »

And the WINNER is… View on YouTube If you missed the build video you can view it here: View on YouTube

Watch this video »

« prev 1 2 3 4 5 ... 516 next »
5152 videos


DISCLAIMER: Any posts on LJ are posted by individuals acting in their own right and do not necessarily reflect the views of LJ. LJ will not be held liable for the actions of any user.

Latest Projects | Latest Blog Entries | Latest Forum Topics

HomeRefurbers.com