LumberJocks

Woodworking forum topics tagged with 'fix'

  • Advertise with us
All Topics Replies Last post
View LoyalAppleGeek's profile

New Chainsaw Parts, No Start

11-16-2017 11:11 PM by LoyalAppleGeek in Power Tools, Hardware and Accessories

Hello everyone! I’m not sure how woodworkerish this question is, but...

9 11-17-2017 10:57 PM
View jeth's profile

Bandsaw upper wheel bearing, loose fit in bore...

10-28-2017 11:54 PM by jeth in Power Tools, Hardware and Accessories

Hello Lumberjocks.. been a while once again, I’m afraid I am like one o...

15 10-31-2017 04:50 PM
View LoyalAppleGeek's profile

Starrett Protractor Square Stuck Tight

08-12-2017 10:54 PM by LoyalAppleGeek in Hand Tools

Greetings and salutations Lumberjocks! I recently acquired a 3 piece Starr...

6 09-23-2017 03:18 AM
View Hoowaa's profile

Help fixing cast iron blade drive on table saw

01-18-2017 03:52 AM by Hoowaa in Power Tools, Hardware and Accessories

I recently discovered the main trunion (cast iron part that holds saw motor) ...

9 05-17-2017 12:41 AM
View dakremer's profile

How flat is flat enough?

05-11-2017 04:45 PM by dakremer in Hand Tools

I’m practicing refurbishing a cheaper Stanley Hand Plane, in hopes of g...

14 05-15-2017 12:20 PM
View Riversalvage's profile

Need help with warped slab table

12-06-2014 03:44 PM by Riversalvage in Woodworking Skill Share

I have a problem on my hands and reputation. I’m a young, novice and...

15 05-13-2017 02:47 AM
View mlipps's profile

Powermatic 141 vibration...please help

10-07-2016 11:40 PM by mlipps in Power Tools, Hardware and Accessories

Hi LJers, Hope all of you are safe those who are braving the storm. I r...

2 10-08-2016 12:42 PM
View Evangogh's profile

To MacGuyver, or not to MacGuyver... That is the question.

08-23-2016 02:58 PM by Evangogh in Power Tools, Hardware and Accessories

I lost the yellow safety tab that clicks into power switch for my lathe (sorr...

5 08-24-2016 06:16 PM
View wanderen's profile

fix trunk split

08-07-2016 01:00 AM by wanderen in Woodworking Skill Share

My grandfather made this trunk for me and it has seen a lot of abuse over tim...

5 08-08-2016 05:01 PM
View bbrettfa's profile

Water based vs. Oil mix up

06-09-2016 06:16 PM by bbrettfa in Finishing

Hello community, I recently embarked on my first woodworking project: a si...

12 06-11-2016 01:16 AM
View jsmestad's profile

Help making cabinet opening 1/8" wider

04-09-2016 12:07 AM by jsmestad in Finishing

I am working on my first true cabinet project. Everything was going well till...

17 04-11-2016 08:26 PM
View PPK's profile

How Do I remove Divots and Milling marks on These (HICKORY) chair legs?

03-21-2016 05:41 PM by PPK in Woodworking Skill Share

Hi all, I have cut out a set of rear chair legs/backs. (the tall parts on ...

15 03-28-2016 09:07 PM
View Cornholesgalore's profile

How to fix lacquer mess up.

11-16-2015 10:19 PM by Cornholesgalore in Finishing

Alright, here’s the situation. I’ve built countless cornholes but...

4 11-19-2015 12:25 AM
View Kevin Violette's profile

Ridgid DP15000 drill press broke and part is obsolete...HELP!

10-30-2013 10:49 PM by Kevin Violette in Woodworking Skill Share

I broke my drill press today it was the rack which is the toothed strip that ...

19 09-03-2015 12:31 AM
View Shubha's profile

Should I be fixing the crack in this table / how could I fix it?

07-10-2015 11:23 PM by Shubha in Finishing

In finishing up my table from a reclaimed bowling alley lane, I cracked the e...

11 07-11-2015 06:18 PM
View splatman's profile

Site for selling used tool parts?

01-09-2015 04:31 AM by splatman in Power Tools, Hardware and Accessories

Is there a site for selling used tool parts?Say, you have a tool that you can...

5 01-12-2015 02:21 AM
View rbeaulin's profile

miter joint didn't turn out so good, now what?

05-06-2014 04:23 PM by rbeaulin in Joinery

I’m working on my very first project, a flag display case. My miter ...

9 05-06-2014 07:43 PM
View Rob's profile

PLEASE HELP!

02-18-2014 04:37 PM by Rob in Woodworking Skill Share

Let me start by saying, I’m a completely self taught ne...

55 03-05-2014 03:24 PM
View Rob's profile

Straight Edge JIG

02-19-2014 12:00 PM by Rob in Woodworking Skill Share

I recently ran into a problem with my current project, and got tons of great ...

6 02-19-2014 06:34 PM
View hcforde's profile

Removing rust from planer post & threads

11-05-2013 06:57 PM by hcforde in Power Tools, Hardware and Accessories

I have a recently purchased a Craftsman planer model 351-23378 that is rusted...

12 11-08-2013 03:16 PM

1 2 3 next »
42 topics


DISCLAIMER: Any posts on LJ are posted by individuals acting in their own right and do not necessarily reflect the views of LJ. LJ will not be held liable for the actions of any user.

Latest Projects | Latest Blog Entries | Latest Forum Topics

HomeRefurbers.com