Ridgid JP0610 Jointer Shipping Box Dimensions?

  • Advertise with us

« back to Power Tools, Hardware and Accessories forum

Forum topic by stefon posted 01-14-2015 08:28 PM 1559 views 0 times favorited 5 replies Add to Favorites Watch
View stefon's profile


14 posts in 1550 days

01-14-2015 08:28 PM

I was looking at purchasing the Ridgid JP0610 and was curious how big the box is that it comes in? I contacted Home Depot but they had no idea (no big surprise).


5 replies so far

View greenacres2's profile


320 posts in 2165 days

#1 posted 01-15-2015 01:18 AM

I know you need a real answer, but…based on my experience it will be slightly larger than the vehicle you’re going to try to squeeze it into. Not so much that you have to take it back into the store, but just enough too big to break the dome light, crack the plastic floor piece that covers the folded seats, forcing you to tie the hatch down on a 34 degree damp day for the 45 minute drive home, make you slide the driver’s seat too far forward, and wish you’d bought the Suburban or F-250 and pay twice as much for fuel the other 364 days of the year.

I’ve never picked up a new Ridgid Jointer, but have picked up too many other tools—and so was able to recognize the question. Good luck!!

View ElChe's profile


630 posts in 1334 days

#2 posted 01-15-2015 01:35 AM

Can’t help on the ridgid. My Jet 6” jointer came in two boxes one for base/motor and one for the cutterhead and the infeed outfeed wings. I was able to fit it in my small pickup but I needed help for the cast iron wings. The motor and base was doable for one person. Can’t they at least tell you if it comes in one or two boxes? Sheesh.

-- Tom - Measure twice cut once. Then measure again. Curse. Fudge.

View ElChe's profile


630 posts in 1334 days

#3 posted 01-15-2015 01:40 AM

Per this amazon review it appears it comes in one box that barely fit in a small pickup. Yikes. That’s a big box!!!

-- Tom - Measure twice cut once. Then measure again. Curse. Fudge.

View Sawdust4Blood's profile (online now)


404 posts in 3019 days

#4 posted 01-15-2015 10:40 AM

I’ve had one for several years but honestly don’t remember the dimensions of the original box. My recollection is that the head unit was fully assembled with the wings already in place and only the stamped steel base required assembly. I know that I brought mine home in a full sized Yukon but Earl’s description would be pretty close to what it would have been like to put it into the wife’s CR-V.

-- Greg, Severn MD

View ChefHDAN's profile


1062 posts in 2847 days

#5 posted 01-15-2015 11:44 AM

Sawdust is correct, fairly simple to assemble and mine was dead on out of the box, but it was also the older grey version. When I purchased mine they were clearing out the grey versions at over 60% off, and I was able to get the jointer, bandsaw, planer, MSUV, two herc lifts, two steel stands, and two flip top stands in to the back of a Ford winstar mini-van, but I’m not 100% sure the front wheels touched the road for the full drive home. I still have part of the jointer box as the cover for my table saw, from my best recollection, besides being HEAVY, figure the box to be 60”x24”x18”

-- I've decided 1 mistake is really 2 opportunities to learn.. learn how to fix it... and learn how to not repeat it

Have your say...

You must be signed in to reply.

DISCLAIMER: Any posts on LJ are posted by individuals acting in their own right and do not necessarily reflect the views of LJ. LJ will not be held liable for the actions of any user.

Latest Projects | Latest Blog Entries | Latest Forum Topics