LumberJocks

Recent Shop Updates

  • Advertise with us

« back to Focus on the Workspace forum

Forum topic by BArnold posted 376 days ago 1097 views 0 times favorited 4 replies Add to Favorites Watch
View BArnold's profile

BArnold

174 posts in 469 days


376 days ago

Topic tags/keywords: resource tablesaw router

Most of my shop time for the past month has been spent on making some changes to the shop itself, rather than ‘real’ projects. Not that this hasn’t been a ‘project’!

Now, I can’t say there was anything ‘wrong’ with my previous table saw set up. I bought the Jet 3hp saw around 2001 when it was packaged with an extension table, router lift and router. As with most saws made then and earlier, the blade guard came off and sat on the shelf. So, no splitter and I was too lazy to try alternative products. Call me very cautious or lucky, but I’ve never had a bad experience. I like my TS surround tables because I can lay a 4’ x 8’ sheet up and have full support while cutting.

Two things (actually three, if you count LOML) motivated me to make some changes: 1) A new table saw with a good implementation of a riving knife; 2) The Incra table saw fence and rail system. Installing the new saw with Incra rails meant some modifications to my surround tables. There are three tables, but they’re tied together for stability and have electrical wiring strung under them, so I had to cut them down in place. I also took the time to change out all of the legs to have adjustability for leveling. The surfaces of the tables were in pretty good shape but I needed to remove the miter tracks and fill the slots. I had thought about installing laminate top surfaces for several years and took this opportunity to do it. Here’s what I ended up with – for now.

My old router lift was a Jet Exacta lift (Jess-Em Mast-R-Lift) that worked just fine. I updated the router to an M12V a few years ago, so I had a good system working. But, now I’m a little older (and more cranky) and wanted a system that will allow easy bit changes above the table. So, enter the Incra (Jess-Em) Mast-R-Lift II and P-C 7518-2 3.25hp router motor.

I haven’t used the router and lift yet, except to test and make sure they function. The saw and Incra fence have seen plenty of use already. The accuracy of the fence is exactly as advertised – calibrate it to your blade and trust it.

I’m lovin’ it that LOML is always supportive of things I want to do with my shop. Of course, now she’s talking about new sofa and loveseat for the family room!

-- Bill, Thomasville, GA


4 replies so far

View Rex B's profile

Rex B

310 posts in 887 days


#1 posted 376 days ago

Looks really good man. You went from one awesome setup to another.

-- Rex

View toolie's profile

toolie

1746 posts in 1265 days


#2 posted 375 days ago

does the bench to the right of the saw in any way interfere with the movement of the incra fence when ripping very wide material?

-- there's a solution to every problem.......you just have to be willing to find it.

View DKV's profile

DKV

3100 posts in 1141 days


#3 posted 375 days ago

Bill, just two things…
1. Did you inherit money?
2. Maybe it is just the photo but is your saw table top sitting below your out feed table?
3. OK, three things…very nice setup.

-- 2014 will be a different year...at least for me it will.

View BArnold's profile

BArnold

174 posts in 469 days


#4 posted 375 days ago

@toolie: The bench to the right is an extension for my miter saw. I cut out the face so the Incra carriage will slide inside. I can get at least 54” cut width.

@DKV: 1. Ha! I wish!!! There are usually two comments I get from people. 1) With everything you have tied up in tools, you could have one heck of a boat! Yeah. What’s your point????? 2) With a shop like this, when do you have time to play golf? Duhhhhhhhhhh…...................................

@DKV: 2. The outfeed table is between 1/8” and 1/4” below the saw table.

Thanks to everyone for you comments!

-- Bill, Thomasville, GA

Have your say...

You must be signed in to reply.

DISCLAIMER: Any posts on LJ are posted by individuals acting in their own right and do not necessarily reflect the views of LJ. LJ will not be held liable for the actions of any user.

Latest Projects | Latest Blog Entries | Latest Forum Topics

HomeRefurbers.com

Latest Projects | Latest Blog Entries | Latest Forum Topics

GardenTenders.com :: gardening showcase