LumberJocks

SawStop table came out of square.

  • Advertise with us

« back to Power Tools, Hardware and Accessories forum

Forum topic by Alan72 posted 09-23-2018 02:46 AM 433 views 0 times favorited 9 replies Add to Favorites Watch
View Alan72's profile

Alan72

216 posts in 2179 days


09-23-2018 02:46 AM

Little over a year ago I was using my saw with my tening jig and the jig nicked the blade which activated the Brake . Every since that occurred I noticed that it was little harder to push material. I would feed the material, halfway through the saw blade, it felt like it was being pinched against the fence. I adjusted the fence kicking it out to the right at the top the table but it did the same thing. This past weekend I was using the saw and switched to the original insert plate and noticed the saw was rubbing against it. I pulled out my manual and proceeded to go through the steps aligning table to the blade. It wasn’t too bad, I adjusted it to insert plate and it worked just perfect. My question is to those who own these saw and If you set off your brake off did your table come out of alignment.


9 replies so far

View therealSteveN's profile

therealSteveN

1410 posts in 720 days


#1 posted 09-23-2018 03:22 AM

Only because you said it started after triggering the safety…........

Page 45 have you done everything they tell you to do after triggering the safety?

If none of that worked I’d call Steve Gass at home.

-- Think safe, be safe

View Redoak49's profile

Redoak49

3527 posts in 2135 days


#2 posted 09-23-2018 11:38 AM

No…my table was fine after a brake activation.

View clin's profile

clin

929 posts in 1142 days


#3 posted 09-23-2018 03:58 PM

I’ve triggered mine once and nothing changed.

-- Clin

View TheFridge's profile

TheFridge

10334 posts in 1632 days


#4 posted 09-23-2018 04:03 PM

Square it up and put it back to work. Even if the brake knocked it out of alignment I’d still lump it in with maintence that has to be done every now and again.

-- Shooting down the walls of heartache. Bang bang. I am. The warrior.

View johnstoneb's profile

johnstoneb

3014 posts in 2319 days


#5 posted 09-23-2018 04:16 PM

I’ve tripped mine no problems afterward.

-- Bruce, Boise, ID

View fly2low's profile

fly2low

22 posts in 243 days


#6 posted 09-23-2018 06:56 PM

I’ve tripped mine without consequences

View Alan72's profile

Alan72

216 posts in 2179 days


#7 posted 09-23-2018 07:57 PM

Thanks to everyone who replied, I am just glad the saw is up and running the way it was prior to the brake going off. .

View Alex Lane's profile

Alex Lane

529 posts in 4036 days


#8 posted 09-23-2018 07:58 PM

Same. A coworker inadvertently touched the blade with a vise grip squeeze clamp. Haven’t checked the alignment on the SS after it triggered, but haven’t noticed any problems yet. Mainly used for precise edge ripping of biplane wing spars with a 7 to 14° bevel angle, and haven’t noticed it out of alignment…with the fence at least. Very rarely even use the miter slot :)

-- Lane Custom Guitars and Basses

View mramseyISU's profile

mramseyISU

549 posts in 1692 days


#9 posted 09-24-2018 01:15 PM



Square it up and put it back to work. Even if the brake knocked it out of alignment I’d still lump it in with maintence that has to be done every now and again.

- TheFridge

I don’t have a sawstop (yet) but I check the alignment on my saw once a year. I get a week shutdown at Christmas time every year and do that along with a bunch of other maintenance in my shop.

-- Trust me I'm an engineer.

Have your say...

You must be signed in to reply.

DISCLAIMER: Any posts on LJ are posted by individuals acting in their own right and do not necessarily reflect the views of LJ. LJ will not be held liable for the actions of any user.

Latest Projects | Latest Blog Entries | Latest Forum Topics

HomeRefurbers.com