LumberJocks

Need help with tool identification for parts sourcing

  • Advertise with us

« back to Power Tools, Hardware and Accessories forum

Forum topic by Nerebel0610 posted 12-12-2017 02:22 PM 1154 views 0 times favorited 19 replies Add to Favorites Watch
View Nerebel0610's profile

Nerebel0610

8 posts in 41 days


12-12-2017 02:22 PM

Good evening gentlemen. I acquired these items quite cheaply. I have no clue if they run. No clue if that motor fits that jointer and no clue where to start the refurbishing process. Any help would be greatly appreciated.

-- "Good decision come from experience; experience comes from bad decisions"


19 replies so far

View splintergroup's profile

splintergroup

1825 posts in 1097 days


#1 posted 12-12-2017 03:55 PM

That motor looks 3-phase, I highly doubt it belongs with the jointer.

View Nerebel0610's profile

Nerebel0610

8 posts in 41 days


#2 posted 12-12-2017 04:02 PM

The motor is three phase 5hp. The there weren’t any other motors laying around so he let me have this one with the deal.

-- "Good decision come from experience; experience comes from bad decisions"

View dhazelton's profile (online now)

dhazelton

2657 posts in 2172 days


#3 posted 12-12-2017 04:09 PM

It looks like you paid scrap prices because you bought scrap metal. Is anything complete? What are you trying to do with them? Are you a woodworker?

View Smitty_Cabinetshop's profile (online now)

Smitty_Cabinetshop

14962 posts in 2493 days


#4 posted 12-12-2017 04:12 PM

Sorry, but you’ve posted some very challenging pictures. Can’t tell what you have…

-- Don't anthropomorphize your handplanes. They hate it when you do that. -- OldTools Archive --

View ShaneA's profile

ShaneA

6879 posts in 2473 days


#5 posted 12-12-2017 04:17 PM

Looks like a Biesemeyer fence and rails, those have value.

Edit: Biesemeyer fence, cant tell if those rails are for it or not.

View jonah's profile

jonah

1524 posts in 3174 days


#6 posted 12-12-2017 04:30 PM

The pictures are terrible, and way too close to actually tell what’s what.

View Nerebel0610's profile

Nerebel0610

8 posts in 41 days


#7 posted 12-12-2017 04:48 PM

The Biesemeyer fence is complete with rail.

The jointer is a “lobo CT-200 8” ” it looks EXACTLY like a GEETECH jointer. It is incomplete at this time with no motor. The plan is to see if the 5hp motor will fit. Im thinking of getting a VFD (variable frequency drive) to be able to run the motor off of single phase power.

The bandsaw is in bad shape it is a transpower unit from tawain which currently isn’t set up to run in the garage I have to swap it out to 110V tonight.

the table saw top wasn’t what I thought it was I thought it was the bottom plate to the bandsaw.

I will take some more pictures of it tonight to show what I picked up but for 200 bucks I wasn’t expecting it to be easy.

-- "Good decision come from experience; experience comes from bad decisions"

View HokieKen's profile

HokieKen

4595 posts in 1014 days


#8 posted 12-12-2017 04:52 PM

I imagine that motor most likely went with the table saw. Pretty sure a 3ph/5hp motor didn’t come with a generic Taiwanese jointer. As stated, if you want much advice, you’ll need to post some better pics. And post them right-side-up…

-- Kenny, SW VA, Go Hokies!!!

View HokieKen's profile

HokieKen

4595 posts in 1014 days


#9 posted 12-12-2017 04:54 PM

If that motor runs, don’t waste it on a jointer. Sell it and buy a good single phase 1-1.5 hp motor for the jointer. You should still walk away with a little cash in pocket.

-- Kenny, SW VA, Go Hokies!!!

View Nerebel0610's profile

Nerebel0610

8 posts in 41 days


#10 posted 12-12-2017 05:28 PM



I imagine that motor most likely went with the table saw. Pretty sure a 3ph/5hp motor didn t come with a generic Taiwanese jointer. As stated, if you want much advice, you ll need to post some better pics. And post them right-side-up…

- HokieKen

I was thinking of using the motor and that table top and building a table saw would it really be that hard to source the parts required for this?

-- "Good decision come from experience; experience comes from bad decisions"

View Nerebel0610's profile

Nerebel0610

8 posts in 41 days


#11 posted 12-13-2017 02:50 AM

Also for that fence would it be easier to completely replace the table saw top with the one that already has the fence mounted or mount the rails to my table saw? I have a Ridgid 3650 currently

-- "Good decision come from experience; experience comes from bad decisions"

View MrUnix's profile (online now)

MrUnix

6199 posts in 2074 days


#12 posted 12-13-2017 03:48 AM

Those do not look like Biesemeyer fence rails although they may work for it. But even so, it appears you are also missing the guide tube.

The rest of the stuff is unidentifiable given the pictures you provided. Post some better pictures, and a clear shot of the motor data plate at least.

Cheers,
Brad

-- Brad in FL - In Dog I trust... everything else is questionable

View Nerebel0610's profile

Nerebel0610

8 posts in 41 days


#13 posted 12-13-2017 04:38 AM

-- "Good decision come from experience; experience comes from bad decisions"

View Nerebel0610's profile

Nerebel0610

8 posts in 41 days


#14 posted 12-13-2017 04:39 AM

The square guide tube is in the garage already I can post it but it’s just squat tube with a table measurer on it.

-- "Good decision come from experience; experience comes from bad decisions"

View Rick_M's profile

Rick_M

10833 posts in 2255 days


#15 posted 12-13-2017 06:52 AM

The router table on the floor is junk. You can build a better one out of a few pieces of plywood.

-- http://thewoodknack.blogspot.com/

showing 1 through 15 of 19 replies

Have your say...

You must be signed in to reply.

DISCLAIMER: Any posts on LJ are posted by individuals acting in their own right and do not necessarily reflect the views of LJ. LJ will not be held liable for the actions of any user.

Latest Projects | Latest Blog Entries | Latest Forum Topics

HomeRefurbers.com