LumberJocks

Grizzly G1022Z TS bearings?

  • Advertise with us

« back to Power Tools, Hardware and Accessories forum

Forum topic by LucasWoods posted 10-28-2016 01:20 AM 504 views 0 times favorited 8 replies Add to Favorites Watch
View LucasWoods's profile

LucasWoods

445 posts in 1474 days


10-28-2016 01:20 AM

Grizzly does not produce replacement parts for this model anymore. What size or where can I can bearings for this TS

-- Colorado Springs, CO - USAF


8 replies so far

View MrUnix's profile (online now)

MrUnix

6919 posts in 2340 days


#1 posted 10-28-2016 02:23 AM

Pull them and look, and measure to make sure. Parts diagram shows 6203-2RS bearings for the arbor, but that does not necessarily mean that is what is in there. Do the same with the motor bearings (pull to verify what is in there), then give Lynne a call at Accurate Bearings and she will hook you up.

Bearings are off the shelf items, so never buy them from the OEM or aftermarket suppliers unless you want to pay out the nose for bearings of unknown origin. I’ve seen bearings sold by manufacturers specific for a particular machine that cost upwards of $30-$40, while the same bearing of better quality can be had at places like Accurate for around $4 a piece.

Cheers,
Brad

-- Brad in FL - In Dog I trust... everything else is questionable

View LucasWoods's profile

LucasWoods

445 posts in 1474 days


#2 posted 10-28-2016 02:32 AM

Thank you very much brad

-- Colorado Springs, CO - USAF

View Quanter50's profile

Quanter50

278 posts in 2437 days


#3 posted 10-28-2016 11:28 AM

If you have a Tractor Supply Store near you, they will have it.

View LucasWoods's profile

LucasWoods

445 posts in 1474 days


#4 posted 11-04-2016 03:29 AM

What information do i need to go in and buy the bearings? If I were to buy them from accurate bearings do they know what sizes are used or do I need to take down measurements etc?

-- Colorado Springs, CO - USAF

View MrUnix's profile (online now)

MrUnix

6919 posts in 2340 days


#5 posted 11-04-2016 03:47 AM

Lynne doesn’t know squat about woodworking machinery – she sells bearings, so you need to tell her what you have/need. If you are positive of a specific bearing (eg: 6203-2RS), you can just ask for them by number and that is what she will send you. If you are not positive of the number, then measurements will help verify – and sometimes she will ask if you measured them just to make sure. With the measurements, she can help find the right bearing for you in that case. For example, the OD, bore and outer race width are identical between the 6203, 88503 and 87503 bearings, but the later have extended inner races that are wider than that of a 6203.

For general info, there is a ‘sticky’ in the OWWM forums titled something like “Ordering bearings from Accurate” that will give you all you need. Unfortunately, they have been having some server problems for the last few days and are currently down. You can check out the document when they are back up – unfortunately, I don’t have a local copy.

Cheers,
Brad

-- Brad in FL - In Dog I trust... everything else is questionable

View LucasWoods's profile

LucasWoods

445 posts in 1474 days


#6 posted 11-04-2016 04:36 AM

Thanks brad even though everything you just said made no sense lol. Looks like I need to read that guide and get more knowledgeable about bearings

-- Colorado Springs, CO - USAF

View MrUnix's profile (online now)

MrUnix

6919 posts in 2340 days


#7 posted 11-04-2016 06:51 PM

Don’t fret.. it’s not that hard :) There are really only a handful of bearing sizes you will run across on these machines, and the 62xx series is about the most common… yank yours and see what is stamped on the side, measure just to make sure, and you will be good to go.

And it seems like OWWM is back up, so here is the document I mentioned:
Ordering Bearings From Accurate Bearing - Please Read

Cheers,
Brad

-- Brad in FL - In Dog I trust... everything else is questionable

View LucasWoods's profile

LucasWoods

445 posts in 1474 days


#8 posted 11-04-2016 07:15 PM

Thanks brad and will do.

-- Colorado Springs, CO - USAF

Have your say...

You must be signed in to reply.

DISCLAIMER: Any posts on LJ are posted by individuals acting in their own right and do not necessarily reflect the views of LJ. LJ will not be held liable for the actions of any user.

Latest Projects | Latest Blog Entries | Latest Forum Topics

HomeRefurbers.com