Table saw purchase dilemma

  • Advertise with us

« back to Power Tools, Hardware and Accessories forum

Forum topic by trevor7428 posted 08-17-2016 01:48 AM 1445 views 1 time favorited 26 replies Add to Favorites Watch
View trevor7428's profile


266 posts in 1105 days

08-17-2016 01:48 AM

So it is time to purchase a new table saw. A upgrade from my current delta 36-725 purchased at lowes.

At first I thought this would be an easy decision. I was planning on getting the sawstop 1.75HP PCS 36”
Plus all the accessories I need: mobile base (which in my opinion should be build in, not sold separated) dado cartridge, dado insert. Which ends up being $3,023.87 (after tax)

Well then I started thinking if I’m going to spend that much on a table saw, I might the 3HP with all the same accessories. Ends up being $460 more or $3,486.92 (after tax)

Sure enough, I can’t make up my mind. I no sawstop is top of the line saw plus finger saving safety feature, but are there other brands out there I should still consider?

Or just go for my origional idea and go for sawstop.

I have no one on one experience with any other top of the line saw. (Jet, powermatic, grizzly, etc)

Can anyone recommend a saw I should consider?

Btw, Woodworking is a hobby for me. The reason
I want a saw stop is mainly for the insurance policy. I am always careful around power tools, but I work with my hands and can’t enjoy my expensive hobby if I lose my job for having less than 10 fingers.

I’m just trying to consider my options before this expensive purchase

-- Thank You Trevor OBrion

26 replies so far

View bbasiaga's profile


1240 posts in 2139 days

#1 posted 08-17-2016 02:33 AM

You’ll get a lot of opinions here, as Sawstop is very polarizing. I love my PCS 3hp. If you have the money, it is a top notch cabinet saw AND has the safety feature. The grizzly 690 and 1023 series are good saws and cost between 1500 and 2k, so a little less. Both are 3hp IIRC. The PM2000 saw can be had in the same range as the sawstop. It has a larger table and is generally heavier.

For me, the 36” rip capacity (vs. 30” for a lot of others, unless you go up to 50” which I didn’t have room for) was a big selling point. If you get the ICS mobile base with the PCS conversion (more money though), it is the best in class base. Fully hydraulic, omnidirectional. Also worth the extra cost, IMO. Plus, the safety feature. The saw was in perfect alignment from the factory (I checked). PM probably would be. Grizzly, idk. But they can be aligned if you’re willing to do the work.

If you’re going 3hp, do you have 220v power already? That adds to the cost. Also of note, the 3hp PCS comes with the upgraded blade guard that can work with the over arm dust collection accessory. The 1.75hp does not, but it can be bought separately. Don’t know why, and doesnt’ matter if you don’t want the overarm collection system.

Go saw stop and you won’t be disappointed. Its top shelf. The other saws are good saws too.

-- Part of engineering is to know when to put your calculator down and pick up your tools.

View JPJ's profile


819 posts in 2764 days

#2 posted 08-17-2016 02:45 AM

You won’t regret the Sawstop 3hp I love mine!

View WhoMe's profile


1564 posts in 3387 days

#3 posted 08-17-2016 04:23 AM

Another vote for the saw stop. I have the 3hp, 36” pcs, with the ics mobile base. Absolutely love mine. Had been wanting and saving for one for a while but a kick back and almost cutting the ends of 3 fingers off due to a brain fart, forced the issue for the purchase before I was ready. Even though I am as safe as I can be, the saw will keep me safer when I have another brain fart. That alone is worth the saw price to me and the wife.
No regrets on the purchase at all. The saw is a pleasure to use every time.

I tell people the “wife acceptance factor” is very high for this saw.

-- I'm not clumsy.. It's just the floor hates me, the tables and chairs are bullies, the wall gets in the way AAANNNDDD table saws BITE my fingers!!!.. - Mike -

View dalepage's profile


367 posts in 985 days

#4 posted 08-17-2016 04:33 AM

For sure get a 3-horse motor. In a 10-inch saw, you’ll have so much more options without bogging down and/or burning the wood. I use a lot of cherry and it’s good to be able to move it through quickly so that it doesn’t burn. I’d never go back to an under-powered saw.

-- Dale

View knotscott's profile


8129 posts in 3520 days

#5 posted 08-17-2016 09:48 AM

As long as you’re not taking food of the family table, I doubt you’ll ever regret getting the 3hp PCS, but you probably regret NOT getting it! The jump to 3hp is significant….it’ll allow you to dictate the pace, rather than the saw. The motor will also rarely if ever strain, so should last longer. Plus it’ll be less sensitive about blade selection and alignment. No real downside to 3hp if you have 220v and the budget.

If you really need to trim cost, but still want the bigger saw, the Grizzly G1023RL is a heck of a deal.

-- Happiness is like wetting your pants...everyone can see it, but only you can feel the warmth....

View Woodbum's profile


826 posts in 3210 days

#6 posted 08-17-2016 10:42 AM

I own a Grizzly 1023 and am very pleased with the value that the saw offers; as well as the performance. I have not owned a Sawstop, but I sell them in my part time job; and they are really a fine piece of machinery even without the flesh sensing safety feature. I would recommend that if you do decide on the Sawstop, that you make the leap to the 3hp; and get all of the accessories that you want when you buy the saw. It is better to get what you want in one slightly larger purchase than to keep going back to the money well for after purchase accessories.

As Knotscot, the LJ table saw subject matter expert said; the Grizzly 1023 series is a great saw for a fraction of the money that the Sawstop will set you back; the performance is terrific and their customer service is great. You can buy one and still have pretty much enough money left to buy another stationary tool for your shop from Grizzly such as one of their very good band saws or a helical head 8” joiner. The value and the quality are there.

In the same price range as the Sawstop is the Powematic PM2000 which has traditionally been an excellent saw and a standard of the industry. If I were going to spend that kind of money though; it is a no brainer…I would get the Sawstop.

-- "Now I'm just another old guy wearing funny clothes"

View rwe2156's profile (online now)


3090 posts in 1625 days

#7 posted 08-17-2016 11:53 AM

I totally agree a 3HP cabinet saw will be a one time purchase and will last your lifetime.
But you’ll have to get away from SS or PM if you’re looking for a more budget conscious saw.

My Jet Xacta has served me well for over 10+ years. I’ve never touched a setting on it and every time I’ve checked its dead on. The Biesmeyer fence is the only way to go IMO.

A quality tool also retains its value. My Jet was ~$1600 10 years ago and I think I could sell it for $1200. The same saw is around $2500 today.

Keep in mind a SS will not save you from kickbacks or loose knots flying (hopefully) past your face, which, BTW are much more apt to happen than putting your hand on the blade.

-- Everything is a prototype thats why its one of a kind!!

View trevor7428's profile


266 posts in 1105 days

#8 posted 08-17-2016 07:31 PM

For some reason, i think all i need is 1.75 HP sawstop PCS 36” (l don’t know why, maybe because its cheaper and my brain is telling me, that’s all I need lol) This will be my biggest purchase ever, besides my house and vehicle.

If anyone thinks I’m making a mistake, by not buying the 3HP. Please tell me after reading

After reading and watching a bunch of sawstop reviews online, I think the 1.75HP is best because
1. Woodworking is a hobby, not profession
2. Don’t cut 8/4 hardwood (never as of yet) even if I ever do, couldn’t I just feed it slow with a sharp rip blade and ill be fine?
3. In the future if I absolutely needed 3HP. I founf out i can upgrade the engine to 3HP (not sure how realistic this is or how difficult)
4. I do have 220v in my garage (only 1 outlet) but its not near, where the table saw will be going (right dab in the middle of the garage) haven’t looked into 220v extention cords, but would assume its best to plug saw straight into outlet.

But please, Tell me after all this do you think its still worth it to get the 3 HP from the get go? The only downside about getting 1.75 HP, is my local woodworking store does not have any in stock right now and won’t receive any more till Monday but of course they do have the 3HP one in stock now. I do not own a truck. So it makes things more difficult. Have to work around the schedule of my buddy with truck and also my own work schedule.

And even tho I do make good money. $3000 is way more than I would like to spend on a saw. The 3HP is Approx $3500 both are going to put a dent in my pocket. (Still have plently enough for all my other bills and then some) but since I technically can afford the 3HP, does that alone beat all the other reasons, I listed above?

-- Thank You Trevor OBrion

View mike02130's profile


170 posts in 817 days

#9 posted 08-17-2016 07:40 PM

Just be careful and buy a used Delta unisaw that’s 3hp. I see them averaging 600. Don’t fret.

-- Google first, search forums second, ask questions later.

View WhyMe's profile


1053 posts in 1705 days

#10 posted 08-17-2016 08:50 PM

If you’re just a hobbyist, why isn’t the Delta 36-725 you have good enough? Other than it’s blade won’t stop if nicking a hotdog, what can’t it do for you?

View JayT's profile


5864 posts in 2355 days

#11 posted 08-17-2016 08:56 PM

I agree with WhyMe. The first two and last reasons you list for the 1.75HP are also reasons to just stay with the Delta. For $3k you are getting very little upgrade in capability with the 1.75HP PCS. The only major benefit is the safety feature. At least with the 3HP, you are moving up the scale in performance, as well as adding the safety.

-- In matters of style, swim with the current; in matters of principle, stand like a rock. Thomas Jefferson

View Rentvent's profile


151 posts in 993 days

#12 posted 08-18-2016 12:47 AM

If 1.75 HP is all you need, then maybe consider the SS contractor saw with cast iron wings. The table is the same size as the PCS and the 36” fence system is exactly the same.

the 3HP PCS comes with a NEMA 6-15P plug. You can make a longer power cord for the saw with a regular extension cord (preferably 12ga). There are instructions with the saw that give detail but it’s easy. The outlet in the garage might need to be changed out to a NEMA 6-20 and the corresponding breaker changed out to 20A or less.

If you are patient, you can try to wait for a deal. I got a new 3HP PCS from Amazon about six weeks ago for $2499 with tax and shipping included.

BTW, there’s a used CNS-175 with 30-inch fence on Amazon right now for $1224 shipped from Amazon warehouse deals.

View mlipps's profile


120 posts in 1259 days

#13 posted 08-18-2016 12:53 AM

+1 for the SS 3hp. Also spend the extra money and get the industrial mobile base. Navigating a 450lb shopping cart (wheel functionality is the same…and as a car actually) is tough. Having 4 wheels (on the industrial mobile base) makes moving it a breeze. It’s a lot of money definitely. I’ve had both the PCS and ICS and I haven’t been sorry that I spent the money. Buy it, you’ll never look back.

View knotscott's profile


8129 posts in 3520 days

#14 posted 08-18-2016 12:59 AM

Once you get anywhere near the price range of a PCS, I think it makes sense to get a saw that you will love, vs one that’s sufficient for the task that you will “like”. My thinking is that you’ve gone way beyond just the utility of being able to cut wood, so why not maximize the value of the high price, get the 3hp motor and love it every time you’ll use it? I think that’s where the sweet spot for value is, plus having nearly double the power has some obvious advantages. Some of that $420 premium will come back to you in resale value too.

It’s sort of like making the decision to buy a premium luxury car like a Mercedes (vs a Chevy), then trying to cut some cost by downgrading with a smaller engine and manual windows. I’m afraid you’ll regret going to this level and not getting the whole package.

-- Happiness is like wetting your pants...everyone can see it, but only you can feel the warmth....

View DirtyMike's profile


637 posts in 1046 days

#15 posted 08-18-2016 01:03 AM

In my opinion if you spend that kind of money and didn’t get the 3hp you would seriously regret it. My saw has got me in trouble because it is under powered, nothing worse than have to back out of a cut. Also with the 1.75 hp you will most likely need a thin kerf blade, Can they be used on saw stop?. Keep in mind that your blade options are limited too when you buy a saw stop. Buy a blade with shoulders and you just defeated your $3000 piece of mind. A used uni saw or powermatic is where its at and you would be buying american.

Buying the 1.75hp instead of the 3hp would be buying the v6 that gets the same mpg as the v8.

showing 1 through 15 of 26 replies

Have your say...

You must be signed in to reply.

DISCLAIMER: Any posts on LJ are posted by individuals acting in their own right and do not necessarily reflect the views of LJ. LJ will not be held liable for the actions of any user.

Latest Projects | Latest Blog Entries | Latest Forum Topics