LumberJocks

WANTED: Some basic custom tablesaw work done

  • Advertise with us

« back to Woodworking Trade & Swap forum

Forum topic by customturnedwork posted 01-27-2016 09:55 PM 938 views 0 times favorited 21 replies Add to Favorites Watch
View customturnedwork's profile

customturnedwork

43 posts in 1114 days


01-27-2016 09:55 PM

Hi everyone,
Since I don’t have a table saw, I was wondering if any of you could quickly whip up some pieces of wood for me (for a price off course). Or does anyone know where a product like this could be found?

I need 11 pieces of hardwood (probably oak), that have an cross section like the image below:


21 replies so far

View MadMark's profile

MadMark

979 posts in 1028 days


#1 posted 01-28-2016 01:52 AM

How many miles of this do you need? 3/32” ok for the kerf?

M

-- Madmark - Madmark2150@yahoo.com Wiretreefarm.com

View customturnedwork's profile

customturnedwork

43 posts in 1114 days


#2 posted 01-28-2016 02:10 AM

3/32 would work for the kerf, though 1/8 would probably be preferable; I would need 11 – 15 pieces of this that are 18” long. I would realyl appreciate it if someone could do this…

View MadMark's profile

MadMark

979 posts in 1028 days


#3 posted 01-28-2016 02:27 AM

How does $1 each sound + shipping, in oak?

When do you need them ?

M

-- Madmark - Madmark2150@yahoo.com Wiretreefarm.com

View ayryq's profile

ayryq

94 posts in 1767 days


#4 posted 01-28-2016 01:01 PM

If you posted your location, you might find someone nearby willing to share some shop time and a beer with you… beats paying shipping.

View dhazelton's profile (online now)

dhazelton

2468 posts in 1872 days


#5 posted 01-28-2016 01:22 PM

A 1/8 inch kerf is 2/16ths – the height of your ends is 3/16ths. That leaves a 32nd on each side of the kerf. There is almost no meat left.

View skatefriday's profile

skatefriday

383 posts in 1058 days


#6 posted 01-28-2016 02:10 PM



How does $1 each sound + shipping, in oak?

When do you need them ?

M

- MadMark

Sounds too cheap! :-)

View customturnedwork's profile

customturnedwork

43 posts in 1114 days


#7 posted 01-28-2016 02:54 PM

Sorry, for the error… It was meant to be 3/8” height, not 3/16”...

View Nubsnstubs's profile

Nubsnstubs

914 posts in 1305 days


#8 posted 01-28-2016 03:05 PM

How deep is the kerf? What’s with the 16 3/8°? Will 16° work, or does it have to be 16 3/8°. like ayryq said, find yourself a beer buddy, and visit him. Make them yourself, but only drink with him after you’re done…... 2 cents…....... Jerry (in Tucson)

-- Jerry (in Tucson)

View MadMark's profile

MadMark

979 posts in 1028 days


#9 posted 01-30-2016 01:48 AM

How does this look?

Angle was cut 16.3°

M

-- Madmark - Madmark2150@yahoo.com Wiretreefarm.com

View customturnedwork's profile

customturnedwork

43 posts in 1114 days


#10 posted 01-30-2016 01:56 AM

Mark,
I’ve sent you an email. One question about that pic though: is it just an illusion, or is the bottom of that piece not flat?

Benjamin

View endgrainy's profile

endgrainy

247 posts in 1463 days


#11 posted 01-30-2016 02:01 AM

@customturnedwork – just out of curiosity, what are you planning to do with these pieces?

-- Follow me on Instagram @endgrainy

View customturnedwork's profile

customturnedwork

43 posts in 1114 days


#12 posted 01-30-2016 02:02 AM

A thank you to everyone else for their advice; unfortunately, I’m young, and can’t drive to any buddies place. Plus, my mother would be concerned about my fingers becoming stubs, especially as I’m a pianist. And since I’m under age, so the beer wouldn’t be legal LOL…

View customturnedwork's profile

customturnedwork

43 posts in 1114 days


#13 posted 01-30-2016 02:09 AM

endgrainy: it’s top secret! (just joking). I will however, leave you in suspense until I reveal the finished project (if it succeeds), a couple months from now on this forum…

View MadMark's profile

MadMark

979 posts in 1028 days


#14 posted 01-30-2016 02:17 AM

Its an optical illusion the bottom is a straight rip.

M

-- Madmark - Madmark2150@yahoo.com Wiretreefarm.com

View endgrainy's profile

endgrainy

247 posts in 1463 days


#15 posted 01-30-2016 02:17 AM

Woo, exciting and mysterious. Good luck!

-- Follow me on Instagram @endgrainy

showing 1 through 15 of 21 replies

Have your say...

You must be signed in to reply.

DISCLAIMER: Any posts on LJ are posted by individuals acting in their own right and do not necessarily reflect the views of LJ. LJ will not be held liable for the actions of any user.

Latest Projects | Latest Blog Entries | Latest Forum Topics

HomeRefurbers.com