LumberJocks

What is it

  • Advertise with us

« back to Coffee Lounge forum

Forum topic by kolwdwrkr posted 09-06-2009 03:56 AM 1077 views 1 time favorited 22 replies Add to Favorites Watch
View kolwdwrkr's profile

kolwdwrkr

2821 posts in 3055 days


09-06-2009 03:56 AM

Topic tags/keywords: jig

Alrighty, I figured I’d give this a go. This could be easy for you. This is not my jig, I did not design it, invent it, etc. I just use it. The guy who made it moved. So Steven if you see this you can’t guess man. LOL
The prize is feeling good that you knew what it was. LOL. So here it is.

Photobucket
Photobucket
Photobucket

I’ll post the answer tomorrow evening

-- ~ Inspiring those who inspire me ~


22 replies so far

View lew's profile

lew

11340 posts in 3220 days


#1 posted 09-06-2009 04:02 AM

I made two of these when I was in the Navy. They are used to put the crease in the bell bottom pants!

-- Lew- Time traveler. Purveyor of the Universe's finest custom rolling pins.

View cabinetmaster's profile

cabinetmaster

10874 posts in 3023 days


#2 posted 09-06-2009 04:10 AM

Looks like a jig for boring hinges into a door. 35MM euro hinges.

-- Jerry--A man can never have enough tools or clamps

View a1Jim's profile

a1Jim

115202 posts in 3042 days


#3 posted 09-06-2009 04:15 AM

I think it’s for clips for 35 mm hinges on face frames

-- http://artisticwoodstudio.com Custom furniture

View patron's profile

patron

13537 posts in 2806 days


#4 posted 09-06-2009 04:17 AM

used to mount base euro base-plates into face frame cabinets ,
insert hinge in jig with base plate attached ,
and drill positioning holes for base-plate
for inset doors .

-- david - only thru kindness can this world be whole . If we don't succeed we run the risk of failure. Dan Quayle

View kolwdwrkr's profile

kolwdwrkr

2821 posts in 3055 days


#5 posted 09-06-2009 05:43 AM

clue: the material was scrap and the hinge holes have nothing to do with it

-- ~ Inspiring those who inspire me ~

View lew's profile

lew

11340 posts in 3220 days


#6 posted 09-06-2009 03:49 PM

A stop block setup for the rip fence on your saw

-- Lew- Time traveler. Purveyor of the Universe's finest custom rolling pins.

View patron's profile

patron

13537 posts in 2806 days


#7 posted 09-06-2009 03:55 PM

a jig that didn’t work out ,
which is why steven left ?

-- david - only thru kindness can this world be whole . If we don't succeed we run the risk of failure. Dan Quayle

View a1Jim's profile

a1Jim

115202 posts in 3042 days


#8 posted 09-06-2009 04:38 PM

a router table of shaper axillary fence

-- http://artisticwoodstudio.com Custom furniture

View Roger Clark aka Rex's profile

Roger Clark aka Rex

6940 posts in 2900 days


#9 posted 09-06-2009 06:13 PM

A super sticky swisher – I had one just like it but all the wheels fell off

-- Roger-R, Republic of Texas. "Always look on the Bright Side of Life" - An eyeball to eyeball confrontation with a blind person is as complete waste of Time.

View ellen35's profile

ellen35

2724 posts in 2897 days


#10 posted 09-06-2009 07:00 PM

I think you measure spaghetti with it and then it shoots down the wood into the water.

-- "Don't let the perfect be the enemy of the good." Voltaire

View kolwdwrkr's profile

kolwdwrkr

2821 posts in 3055 days


#11 posted 09-07-2009 03:13 AM

This jig is used with the table saw. With that in mind, Any guesses? I’ll tell the answer in 2 hours or there abouts.

-- ~ Inspiring those who inspire me ~

View patron's profile

patron

13537 posts in 2806 days


#12 posted 09-07-2009 03:17 AM

set the saw to flush cut overhang on the bottom of boxes ,
or making stop dadoes from either end .

-- david - only thru kindness can this world be whole . If we don't succeed we run the risk of failure. Dan Quayle

View Craftsman on the lake's profile

Craftsman on the lake

2523 posts in 2903 days


#13 posted 09-07-2009 03:32 AM

A rail riding push block.

-- The smell of wood, coffee in the cup, the wife let's me do my thing, the lake is peaceful.

View papadan's profile

papadan

1175 posts in 2833 days


#14 posted 09-07-2009 03:37 AM

Looks like a long skinny memo pad to me!

-- Carpenter assembles with hands, Designer builds with brains, Artist creates with heart!

View kolwdwrkr's profile

kolwdwrkr

2821 posts in 3055 days


#15 posted 09-07-2009 05:50 PM

This jig is used for mitering on a right tilt saw. It helps prevent the stock from being caught between the blade and the fence and prevents the inevidable kickback. Here are some pics for your amuzement.
Photobucket
Photobucket
Photobucket
Photobucket
Photobucket
Photobucket
Photobucket
Photobucket

-- ~ Inspiring those who inspire me ~

showing 1 through 15 of 22 replies

Have your say...

You must be signed in to reply.

DISCLAIMER: Any posts on LJ are posted by individuals acting in their own right and do not necessarily reflect the views of LJ. LJ will not be held liable for the actions of any user.

Latest Projects | Latest Blog Entries | Latest Forum Topics

HomeRefurbers.com