LumberJocks

spanky46's Favorites

  • Advertise with us
View Filinvested's profile

Scraps to Beads

1405 days ago by Filinvested | 20 comments »

I’ll try to explain how I did this project:http://lumberjocks.com/projects/38288 1. I take a cutoffs, which just can’t to waste 2. Cut them into small pieces, not necessarily cubic: 3. Disks we need: 40, 120, 320 sand paper and wool disk 4. A tin and PVC stripes for soundproofing: 5. My driil. It can work for hours at speed ‘C/D’ (i have been told it could be problem for drills). 6. An IKEA stool and milled groove in it for the tin. 7. The...

Read this entry »


View DaveTPilot's profile

Shop Made Router Lift and Table

1375 days ago by DaveTPilot | 21 comments »

Read this entry »


View KylesWoodworking's profile

Making a CNC Router #4: Part 4: Electronics

1200 days ago by KylesWoodworking | 5 comments »

After a few months of saving money, I finally got all the electronics for my CNC! I purchased all the electronics from: http://buildyourcnc.com/electronicscombo.aspxwhich include:(3) 425 oz-in stepping motors(3) Drivers (3.0Amp 24-40 Volts, 1-1/64 microstepping)(1) 36v 8.8a Power Supply (1) Breakout board Then I built a box out of poplar and Plexiglas to house all the electronics: Then I tried out the monitor shelf that I came up with in the last b...

Read this entry »


View SPalm's profile

Steps Cutting Board Version 2 (Two Step)

1465 days ago by SPalm | 67 comments »

This is a second generation Steps cutting board made out of walnut, maple, and cherry. The first Steps board I made used a basic square with edge of maple and cherry to make it a block and a notch to do the stepping. I wanted to try to make a stepping board using the hex Tumbling Block design, and this is what I came up with. In order to make the hex do the stepping, I needed to notch all three sides, as can be seen in the Sketchup drawing. The cool thing here is that it steps in two di...

Read this entry »


View SPalm's profile

Staggered Steps Endgrain Cutting Board

1517 days ago by SPalm | 43 comments »

This is a new style of cutting board (at least new to me). I was thinking about 3D designs on the way home from work last week, after Martyn’s Blog and Steve’s Video. So I came up with this. Kind of Sinister, kind of Tumbling block. Once I drew it out, it reminded me of Staggered Stairs (which are kind of cool), and reminded Karen of the Steps on the Row Houses in Baltimore. So that is how the name came about. I started with 6/4 walnut cut into 10 inch strips. This small length makes ...

Read this entry »


View SPalm's profile

Another Cutting Board Design

1501 days ago by SPalm | 26 comments »

I am in the process of building another board and thought I would share my thinking process along with some build pictures. When I came up with the design for the Steps board, I was thinking about how one draws a 3D box on a piece of paper. You draw a large square, and then add small mitered edges to one corner to give the appearance of seeing it slightly from the side. Making these miters out of two different woods adds to the shadows, which adds to the effect. I did this for the Steps b...

Read this entry »


View patron's profile

making a 'bow tie' circle pattern - tutorial

1320 days ago by patron | 42 comments »

my ‘did it my way board’ http://lumberjocks.com/projects/42141 was done like thisthe tangents are the square of the circlethe thickness of the stock is that height of the squarethe width of the stock is the square and the two wingsof the circle combined(for my 1 1/4” bits it was 1”x1 1/2”).cut and mill the stockrun the round edges firstso the flat is still good for the coves later.the fence and the cutter tangent want to be exactso there is no loss in w...

Read this entry »


View degoose's profile

Patterns by McLeanVA #2: One and Two.

1412 days ago by degoose | 8 comments »

Just a couple of pics of #1 and #2 and as you can see I downloaded the plans and have included them in the pics. #1.. Standard ZIG ZAG. #2 Thick & Thin ZIG ZAG Please note these are works in progress and are at this stage only a dry fit.. but wet with Mineral Turpentine to colour up…do not comment on gaps or misalignments until they are posted as finished projects..

Read this entry »


View McLeanVA's profile

Cutting Board: How To's #2: Zig Zag Cutting Board Patterns - Inspirational

1416 days ago by McLeanVA | 22 comments »

I was absolutely overwhelmed by the positive response to my Zig Zag How To blog post yesterday, that I decided to brainstorm some possible combinations (on my lunch break) using the basic steps I outlined yesterday. All of the same techniques and steps apply, and really the only difference is the woods and measurements that make up the original “sticks.” Same rules apply to width = height. Length is up to you. Please experiment with whatever measurements and combinations strike...

Read this entry »


View McLeanVA's profile

Cutting Board: How To's #1: Zig Zag Cutting Board - How To:

1417 days ago by McLeanVA | 50 comments »

For those of you who asked me for a tutorial on how to make the zig zag legless vegetable death table (cutting board), here is my best shot. I am far too impatient to take photos when I work, so I decided to illustrate the process using some good old Adobe PhotoShop. I hope you find this useful and informative. I will outline the process in 10 steps below. I have assumed that when viewing these steps that basic woodworking skills are familiar to you. If you have questions, or run into snag...

Read this entry »


1 2 3 next »
22 entries


DISCLAIMER: Any posts on LJ are posted by individuals acting in their own right and do not necessarily reflect the views of LJ. LJ will not be held liable for the actions of any user.

Latest Projects | Latest Blog Entries | Latest Forum Topics

HomeRefurbers.com

Latest Projects | Latest Blog Entries | Latest Forum Topics

GardenTenders.com :: gardening showcase