LumberJocks

scopemonkey's Favorites

  • Advertise with us
View degoose's profile

How to make a endgrain tumbling block butcher block board!

08-12-2009 12:13 PM by degoose | 48 comments »

Hi guys ,, I had a request to make a tutorial with regards the endgrain Tumbling Block Design.First off,.., You need to decide the size of the blocks…. for this example I used 1” stock… Or something similar.. actually just over .. once dressed. Set the blade of the table saw to 60 degrees.. a bevel box makes this simpleI use the INCRA fence system so it is easy to rip bevels off side of the blade.Once the bevels are ripped measure the length of the bevel and move the f...

Read this entry »


View Les Hastings's profile

Curved Doors; Raised panel & Six light glass #1: Finished product

07-01-2008 02:47 AM by Les Hastings | 14 comments »

Let me start off by saying I’ve been absent a while from Lumberjocks, been really busy the last couple of months. Working seven days a week again, yeap its no fun! I’ve had a number of Lumberjocks ask me to do a blog on curved doors,,,,,,,,,Well here it is! We’ve been building another kitchen in the shop, its just about complete. Lucky for you that are interested it has curved doors, two different kind of curved doors. A pair of rasied panel doors and one single six ...

Read this entry »


View Bob Simmons's profile

Let's Turn Salt and Pepper Mills

08-07-2010 06:05 PM by Bob Simmons | 14 comments »

There is something special about wood turning. It is easy to spend hours at this wood craft while working with the various woodturning tools. This particular project features salt and pepper mills of black walnut with a food-safe finish of Tried and True oil varnish. This finish leaves a soft and warm patina with a nice hand rubbed look and feel. The material on hand in the shop happened to be 3/4” black walnut that was left over from another project. In this case the (4) pieces w...

Read this entry »


View poroskywood's profile

Drunken Cutting Boards #1: Drunken Alice in Wonderland Cutting Board

09-10-2009 03:22 AM by poroskywood | 41 comments »

Hey everybody, after a few personal messages here is my version of a how to on a Drunken Checker Board. I of coarse bow to the Chairman of the Board and pay tribute with beer. This is a Off-Checker pattern I call “Drunken Alice in Wonderland” The “serendipitous” nature of this piece is appealing in a far out sort of way. Here Goes… So first I prepare the Material. I am using Hard Maple and Walnut both are surfaced flat and cut 1” x 9” x 14&...

Read this entry »


View ganders's profile

The quick and dirty instructions on how to make a zig-zag pattern cutting board.

08-06-2008 12:26 PM by ganders | 24 comments »

The quick and dirty instructions on how to make a zig-zag pattern cutting board. Click on the pictures to see a full size image. Choose a couple different types of hardwood. The more colors the better. Below is cherry, maple and walnut. Rip strips of wood any width so the total with is about 12”. This is the width that will fit through my planer. The beauty of this is that none of the widths have to be the same. The board shown below is made of scrape wood. If you only have shor...

Read this entry »


View dewoodwork's profile

Beautiful end grain cutting boards free project plan

11-25-2007 07:31 AM by dewoodwork | 94 comments »

Construct these beautiful end grainCutting boards Hello fellow woodworkers,In the spirit of sharing woodworking knowledge I am writing this tutorial for anyone interested in constructing these beautiful end grain cutting boards. Take a look at the photos of the four styles I have made, or create your own pattern’s and follow the steps I have outlined in this tutorial. Questions and comments are welcome, enjoy. For this board I used maple, walnut, lyptus and purpleheart. White oak, wa...

Read this entry »


View Kerux's profile

Decal Pen Tutorial

03-11-2008 09:24 PM by Kerux | 17 comments »

Here is what I basically do with my Decal pens. As you can see I use Testors Decal paper. This can be found at Hobby stores. I purchased mine at “Hobby Lobby.” Just follow the directions for printing out your logo, name…etc. One thing I have found using this material is that you MUST use a light colored blank for the background. This is transparent film, but the inkjet inks are not solid enough for darker colors. That type of decal must be purchased through professional m...

Read this entry »


View Gary's profile

Celtic Knot Pens #1: One way to do it

09-06-2007 04:24 PM by Gary | 16 comments »

This was requested from multiple sites, so I did one for everybody. Here’s some photos of my process;I only had enough time to do a two-ring knot, but it’sall the same to make a four-ring knot accurately if you follow these steps. This shows the miter sled, the length of contrasting wood for the slices, and the bloodwood blank I’m going to use. I’ve already squared the blank so that all four sides are the same size.I randomly pick a side and mark it 1.Side 2 i...

Read this entry »


View Todd A. Clippinger's profile

Sofa Table Dimensions

04-03-2007 11:57 PM by Todd A. Clippinger | 6 comments »

No Rest for the Wicked… ...or the self-employed. Just when I think I am getting some time, well you know the story. I still have not set up anything to drag pictures from. When I first joined I had some down time due to some nasty virus running around and now I’m just behind. A Resourceful Lot… You guys are a resourceful lot, as woodworkers typically are. I have been getting inquiries about the sofa tables and I don’t care if you guys make them, I truly am...

Read this entry »


View GaryK's profile

Wood collection box - how to

05-01-2008 08:40 PM by GaryK | 35 comments »

To see the finished project go here: Here is the sample piece to test the concept. I started with wood planed down to 3/8”, cut to width and left a little long for trimming.I used a 1/2” 45 degree router bit to make the grooves. They are spaces 1/2” apart and 1/4” deep, starting 1/2” from the edge. The width of your wood matters. 1/2” increments works great...To enclose and make the sides a full 1/2” I planed some 1/8” pieces...This is...

Read this entry »


1 2 next »
12 entries


DISCLAIMER: Any posts on LJ are posted by individuals acting in their own right and do not necessarily reflect the views of LJ. LJ will not be held liable for the actions of any user.

Latest Projects | Latest Blog Entries | Latest Forum Topics

HomeRefurbers.com

Latest Projects | Latest Blog Entries | Latest Forum Topics

GardenTenders.com :: gardening showcase