LumberJocks

sb194's Favorites

  • Advertise with us
View Kurt T. Kneller's profile

New Thien Seperator Lid, HFDC, Wynn Filter vs Woodcraft Seperator Lid

01-19-2015 12:31 AM by Kurt T. Kneller | 0 comments »

Up until now I have been using my Harbor Freight DC a 31 gallon garbage can with the separator lid from Wood craft. It worked, but not like I had hoped. I recently purchased the Wynn Environmental filter 35A and started to build a Thein separator lid using 4” hoses. I emptied the contents of the can and DC collection bag on the floor for comparison and then proceeded to install the Wynn filter and Thien separator. I was truly impressed with the overall improvement in performance, th...

Read this entry »


View kiefer's profile

KIEFER KNEE VISE CONSTRUCTION AND SKETCHUP MODEL

12-01-2014 04:45 PM by kiefer | 14 comments »

Here is the blog on how I made the new vise in pictures and a SKETCHUP model that you can download and play with .http://lumberjocks.com/projects/108195The SKETCHUP model was done by LUMBER PUNK /LUKE and he deserves a BIG Thank you from us for donating his time to create the model . https://3dwarehouse.sketchup.com/model.html?id=u3e3dad6a-12ff-45cf-b376-0cd8ca9af4a4Also a Big Thank you to Paul/Shipwright for the maquetry logo .Here is the video link .https://www.youtube.com/watch?v=1vZLa3...

Read this entry »


View mafe's profile

Card scrapers #2: Card scraper stands quick and clean.

11-23-2014 08:54 PM by mafe | 12 comments »

Card scraper standsquick and clean. Yes this is no rocket science, but a quick and joyful practical project that can be made even if all the tools you own is a handsaw and you need no experience to make it.The reason I never made one before are the fact I only had a few card scrapers, so I had no need.The reason I share this project are that I think it’s a wonderful simple project that organize and can make the tools be at hand when needed. I used to have only three card scrapers ...

Read this entry »


View Airframer's profile

Childs Play #2: Toy Handplane Build #2... Drill Press Turning and Stuff..

11-23-2014 11:15 PM by Airframer | 6 comments »

I had hoped to be further along on this by now but progress is still progress I suppose. I am taking some vacation time next week so hopefully I can get this mostly done by the end of the first week of DEC leaving just a few simple tools left to complete the set for Christmas. Anyhoo.. we left off with the rough joints brazed into the aluminum. After sanding for a few hours I finally broke down and picked up a belt sander for the shop. I had been tossing around needing one for about a y...

Read this entry »


View kiefer's profile

MY TABLE SAW SLED (DEMO)

10-07-2014 11:56 AM by kiefer | 18 comments »

Since it seems to be the season for table saw sleds I thought I post a video demo of my table saw sled and like to point out some of the features that sets it apart from other sleds .Some of the features are a double sliding bottom,full tilt of the blade range with zero clearence ,dado capability and several others .http://lumberjocks.com/projects/61820Here is the link to the video and it will explain all the features better than I can explain here . https://www.youtube.com/watch?v=70C...

Read this entry »


View kiefer's profile

Kiefers Little Tapper build

10-01-2014 02:38 PM by kiefer | 23 comments »

http://lumberjocks.com/projects/106249Here is the the build process of the little tapper that I use.I start by sourcing most pieces I need from the scrap bin and cutting them to size .Next I mark out the centre layer of the head and cut it into three pieces using my sled on the table saw .Note the little handy bevel gauge that my buddy Paul http://lumberjocks.com/shipwright made for me and it is just a great little tool .If you look back in my projects you will find the post of my sled http:...

Read this entry »


View WoodAndShop's profile

How to Square, Flatten, & Dimension Rough Boards with Hand Tools {10 Steps}

09-27-2014 11:45 PM by WoodAndShop | 5 comments »

In the above video, and in the below 10 steps, I teach one of the most basic and essential skills in traditional woodworking: how to square, flatten, & dimension your own rough lumber into finished boards. To build quality traditional furniture, you need to start with perfectly flat and square lumber. Some people achieve this with power jointers, planers, and table saws. While the electrical power route is more economical for a commercial woodworking workshop, I prefer the safet...

Read this entry »


View Darrell Peart's profile

Tweaks #1 #2: Tweaks to my Fremont Bed Done

09-14-2014 10:51 PM by Darrell Peart | 11 comments »

Several months ago I posted a proposed design change to the cap rail on my Fremont Bed. At the time, there was a mixed reaction to this. The bed has finally made it to the current spot on my schedule and is now ready to go the finisher. Seeing the bed in “real life” makes it easier to visualize the results. For an easy comparison lets start here with three images from my original post.On the left is the revision – on the right is the original detail While the original design...

Read this entry »


View WoodAndShop's profile

Frank Klausz Cuts a Monster Molding with his Molding Plane

09-05-2014 12:36 PM by WoodAndShop | 2 comments »

In my above video, Frank Klausz takes us into his new woodworking workshop and shows his amazing, and huge, carpenter’s molding plane that he made at the request of his local tool collector group in New Jersey, called the “The Craft”. Frank asked me to share their website link here. Frank wanted to demonstrate this molding plane when I was filming a video tour of his new woodworking workshop. >> Watch the video tour of Frank’s workshop here>> Watch Frank’s Hand Cut Dovetail tutor...

Read this entry »


View degoose's profile

Open weave Lazy Larry #8: The glue up

08-03-2011 08:38 AM by degoose | 11 comments »

Got out nice and early this morning… and here is the glue up video you have all been waiting for … The whole video is actually only 9 minutes long… intro and ending included… the glue up took around 8 minutes and a further couple to fit and adjust the clamps.. So a realistic total of under 10 minutes… not too shabby…

Read this entry »


1 2 3 4 ... 6 next »
55 entries


DISCLAIMER: Any posts on LJ are posted by individuals acting in their own right and do not necessarily reflect the views of LJ. LJ will not be held liable for the actions of any user.

Latest Projects | Latest Blog Entries | Latest Forum Topics

HomeRefurbers.com

Latest Projects | Latest Blog Entries | Latest Forum Topics

GardenTenders.com :: gardening showcase