LumberJocks

LumberJocks Woodworking Reviews

  • Advertise with us
Ultimate saw horse/table

Ultimate saw horse/table

04-12-2009 03:09 PM by Scott Oldre | 12 comments »

This is the ultimate accessory in my garage shop. It, and it’s twin, gets pulled out on nearly every single project I take on. Sometimes it becomes semi permanent, and other times it’s out for an hour or two. I saw this table/horse about 2 years ago while strolling down the “Hey look at me, take me home” display isle at Home Depot and since I was with my wife she nonchalantly wiped the drool from my chin and said “Lets go to the plants now!” Since it wa...

Read this review »


Norton Multi-Oilstone IM313 - I think this is my last sharpening system - updated with video

Norton Multi-Oilstone IM313 - I think this is my last sharpening system - updated with video

04-11-2009 05:47 PM by ChicoWoodnut | 21 comments »

I have been looking at this system for a couple of years now. I finally decided to click the buy button and I’m glad I did. Like most of you, I have tried a lot of sharpening systems. Here are the ones I have tried and the reasons I decided to buy this one and lay the rest aside. Scary Sharp - A good system if you like buying sandpaper all the time. I used it for a long time. The cost of consumables quickly adds up. Work Sharp - A good system but ditto on the consumables. ...

Read this review »


PORTER-CABLE ROUTER BITS

PORTER-CABLE ROUTER BITS

04-08-2009 11:57 PM by Dusty56 | 17 comments »

HELLO , I’m not sure if this is posted in the correct place , so bear with me , Site Police . LOL…I ALSO POSTED IT IN THE forums section , but was unable to post any pix there. It’s too bad that there isn’t anywhere here specifically to post items that we find on sale to help out our jockbuddies. (that I know of ) I went to the W.Springfield MA Woodcraft store today for a bandsaw blade and was introduced to a very nice display of P-C router bits at clearance prices....

Read this review »


Buyer Beware!

Buyer Beware!

04-08-2009 04:10 AM by Topapilot | 34 comments »

A store called “Big Lots!” moved into town this winter, and since I’d heard about clamp deals there I went to find out. They do have “deals”, F-type clamps for $6, parallel clamps for $10. I’ve purchased three types of clamps, the first put to the test were these 24” F-style bar clamps. At the store I was carefull to check that they all worked properly, then bought 10 for $60. When using them I found two problems, and one is a show stopper. Fir...

Read this review »


Heating the shop

Heating the shop

04-07-2009 11:29 PM by Craftsman on the lake | 23 comments »

5 year update:After about 5 years this heater is still working, still heating my shop up to shirt temperatures quickly and costing me about $100/yr to run when I use it often. Needs blowing out with air each season but still starting and running well. Summer is arriving. But, winter will be back. If you live in a cool climate I’d like to share my experiences with shop heat with you. I see a lot of people in blogs who say that they’d like to work but it’s too cold or they ...

Read this review »


JacPac CO2 Compressor - Very Good

JacPac CO2 Compressor - Very Good

04-07-2009 08:57 PM by CharlieD | 13 comments »

Recently, I bought the JacPac CO2 portable compressor product and it sat in my shop for a couple of months before I used it. I like it a lot and will use it a lot… going forward. It is very handy when you have to do work outside a location where you have a compressor or one with no electricity. I took it to a house where I needed to finish up a small job. I took my Bostitch 15 gauge angle nailer and 18 gauge PC. I took the 18 guage because I thought it might not drive the 2 inch ...

Read this review »


Grizzly G1014Z 6x48 belt sander with 9" disc

Grizzly G1014Z 6x48 belt sander with 9" disc

04-06-2009 11:56 PM by NY_Rocking_Chairs | 3 comments »

As I get more and more into the model making side of wood-working I find I need to do some quick sanding and holding the ROS while trying to sand a small piece was getting aggravating. So we stopped at the Grizzly showroom in Muncy, PA. They had both this sander and the smaller 4×36 belt sander. Needless to say the smaller one was out of stock and looked a little small and light for my needs, plus the G1014Z came with a stand. I was forced to wait 5 days before even unpacking it ...

Read this review »


First Saw and Glad I Bought It

First Saw and Glad I Bought It

04-06-2009 02:38 AM by Mookie | 20 comments »

This is my first post and it’s about my first saw. I started woodworking a couple of years ago almost as a fluke. I bought a drill press because it was only $99 and from there I started buyng other power tools and suddenly discovered I really liked woodworking. I bought the Hitachi at Lowe’s after asking a guy at Woodcraft what he thought about the specs of the Hitachi for a beginner. I had no idea what or how much I would be cutting and $500 was a HUGE investment at the time....

Read this review »


Makita 4351FCT Whatajigsaw!!

Makita 4351FCT Whatajigsaw!!

04-05-2009 10:28 PM by matt garcia | 12 comments »

I know there are a lot of Bosch lovers out there, but I took a chance on this jigsaw and man did it pay off! The website indicated it was 40% less vibration than other brands. When I received it, and chucked up one of the new Starrett Dual-Cut blades and turned it on, you could barely feel any vibration. What a huge improvement over the POS Craftsman jigsaw I received as a gift a few years ago. This saw, in unison with the new Starrett blade yielded splinter free cuts on 3/4” oak ...

Read this review »


Bosch 1297DK

Bosch 1297DK

04-03-2009 05:59 PM by bensaw | 5 comments »

I picked up this sander last night at Lowe’s for $52. Seemed a little sturdier than the bargain basement ones from Black and Decker and Skil. The sander seemed stable and was coformtable in my hand so I brought it home. The ROS20VSK from Bosch already has a review here on Lumberjocks. In fact, that review is what sealed the deal when I was at the store. I wanted to see if the experience of this sander would be the same as the ROS20VSK. I don’t know the relationship between the ...

Read this review »


« prev 1 ... 319 320 321 322 323 324 325 ... 388 next »
3878 reviews

Add new review
View Product Index
RSS FEED

Browse reviews

categories | brands | all reviews


DISCLAIMER: Any posts on LJ are posted by individuals acting in their own right and do not necessarily reflect the views of LJ. LJ will not be held liable for the actions of any user.

Latest Projects | Latest Blog Entries | Latest Forum Topics

HomeRefurbers.com

Latest Projects | Latest Blog Entries | Latest Forum Topics

GardenTenders.com :: gardening showcase