LumberJocks

Reviews: Tablesaw Accessories

  • Advertise with us
Happy Camper No. 2,17685 (give or take a few)

Happy Camper No. 2,17685 (give or take a few)

02-09-2016 07:34 PM by Kelly | 5 comments »

I’ve primarily used this for mortised and tenoned frame corners for a kitchen (cuts done with the styles and rails at ninety degrees to the table) and splined corners (cuts done with frame corners at twenty-two and a half to forty-five degrees to the table). The results are, I am very pleased with my purchase. This is a lot of jig for the money. Just lifting it makes clear the fact it’s not a toy. I believe this tenon jig will provide years of service. Though another reviewe...

Read this review »


Making Good Box Joints Easily and Repeatable

Making Good Box Joints Easily and Repeatable

02-09-2016 07:16 PM by Kelly | 1 comment »

I’ve been woodworking, both professionally and as a hobbyist, since 1974. Over those years, my appreciation of the value of jigs has continued to increase. For example, using a circle cutting jig on my band saw allowed me to cut precision circles ranging from a couple inches to three feet in diameter. Box joints, or finger joints, make for strong joints and can add aesthetic value to a project. Laying out multiple box joints, individually cutting them and getting good, tight joints t...

Read this review »


A great dado set..

A great dado set..

01-15-2016 12:13 AM by edwood1975 | 3 comments »

Since I purchased my rigid tablesaw I have been really trying to advance my knowledge of exactly what a TS can do and I figured joinery techniques was a good a place as any.. In in the middle of the design phase of creating mitre saw station and I think the doors will be mortise and tennon joinery anyway I have been practicing with this set.. The Pros:Really like the quality of the blades,chippers and spacers.. I like how easy it is for a beginner like me to align everything in the s...

Read this review »


General International 50-200r with Excaliber 40-070EK Router Table add-on

General International 50-200r with Excaliber 40-070EK Router Table add-on

12-28-2015 08:42 PM by gotnonickname | 3 comments »

I did a review of the 50-200R awhile back and I still have nothing but positive things to say about this saw. I did upgrade the fence to an after market design that has worked flawlessly. The big item I want to remind users of this Super Cool Tools fence rail build is to take you time when making the rails and make sure you use the Starrett measuring tape. Starrett tape is extremely accurate. The saw still is still dead nuts on and has not needed any adjustments. Now on the upgrade. Since my ...

Read this review »


Biesemeyer Fence Major Disappointment

Biesemeyer Fence Major Disappointment

09-24-2015 04:25 PM by Hawk_Guy | 37 comments »

So I finally pulled the trigger on a Biesemeyer table saw fence, the Rolls Royce of fence systems. I will preface this with the statement that I must be the most unlucky consumer on the market or the tool industry has gone to total crap. For those of you who have read my reviews in the past you may be thinking I’m some sort of internet troll out to bad mouth manufacturers. I’ll be frank, if the product is good then I’ll rave about it but if the product stinks I’m go...

Read this review »


Vega Pro 50 Fence - Long winded

Vega Pro 50 Fence - Long winded

08-14-2015 12:30 AM by Kurt T. Kneller | 6 comments »

I needed to increase the cutting capacity of my table saw and last fall I bought a Vega Pro 50 fence system. I originally wanted to get a Biesemeyer, but I really need both my legs and both my arms. My table saw is a Rigid 2424. I wanted to use the fence for a while before writing a review. I have put it through the paces and the following is my take on the fence. Aftermarket fences can be really expensive and may require a good amount of modifications to your table saw. That was not ...

Read this review »


Should have gotten this a long time ago

Should have gotten this a long time ago

07-21-2015 12:29 PM by whope | 12 comments »

The old Sears Craftsman TS *circa early 90’s) I have really doesn’t have a riving knife. Bought a Zero Clearance Insert a few years ago. Usually don’t have a problem with pinching with oak. Started ripping some poplar and the first cut pinched really hard and I stopped and ordered the Micro Jig (as the nearest retailer is a bit of a drive). I waited a whole week before installing it. Not sure why, other than I didn’t have a suitable scrap of 1/2” MDF to use. B...

Read this review »


Grizzly 6" cast iron hand wheel

Grizzly 6" cast iron hand wheel

06-06-2015 04:27 AM by athomas5009 | 10 comments »

I ended up picking up a cpl of these to replace the garbage plastic OEM ones on my Cman 113 saw. I was a little lerious whether they would work because I ran across a few unhappy reviews because of difficulties modifying the fit. Well they arrived today and I couldn’t be happier! The are nice stuffy and turn real smoothly. Installation was a breeze and I don’t see why some would complain. As long as you have a drill press just bore the center hole to 1/2” then pop a 1/4&#...

Read this review »


Grizzly H7583 Tenoning Jig

Grizzly H7583 Tenoning Jig

04-30-2015 12:24 AM by Jagerheister | 27 comments »

A few day ago I purchased a Grizzly tenoning jig for an upcoming project on Amazon for $78.00 USD. I did quite a bit of research prior to pulling the trigger on the purchase, and I didn’t find many sources of video demonstrations or specific product info other than specifications and written instructions. I decided to do a video just to propagate and proliferate information on this product. I’ve provided a link below to a video review that I did of the unboxing, and assembly....

Read this review »


Oshlun HI-ATB Ultimate General Purpose

Oshlun HI-ATB Ultimate General Purpose

04-01-2015 02:17 AM by eljiggo | 5 comments »

Hello Everyone! After reading a review(a very old review at that) knottscott made on the Oshlun General Purpose 40t, I inquired about the Oshlun ULTIMATE general purpose, a hi-atb general purpose. Noone seemed to know anything, so amazon was nice enough to deliver one to me for $34.30. First Impressions: The blade has that aesthestic ferocity to it that only a 40t hi-atb blade can present. It was very sharp out of the box. Close inspection of the blade shows large carbide teeth (not qui...

Read this review »


« prev 1 2 3 4 5 ... 20 next »
195 reviews

Add new review
View Product Index
RSS FEED

Browse reviews

categories | brands | all reviews


DISCLAIMER: Any posts on LJ are posted by individuals acting in their own right and do not necessarily reflect the views of LJ. LJ will not be held liable for the actions of any user.

Latest Projects | Latest Blog Entries | Latest Forum Topics

HomeRefurbers.com