LumberJocks

Reviews: Tablesaw Accessories

  • Advertise with us
Oshlun HI-ATB Ultimate General Purpose

Oshlun HI-ATB Ultimate General Purpose

04-01-2015 02:17 AM by eljiggo | 5 comments »

Hello Everyone! After reading a review(a very old review at that) knottscott made on the Oshlun General Purpose 40t, I inquired about the Oshlun ULTIMATE general purpose, a hi-atb general purpose. Noone seemed to know anything, so amazon was nice enough to deliver one to me for $34.30. First Impressions: The blade has that aesthestic ferocity to it that only a 40t hi-atb blade can present. It was very sharp out of the box. Close inspection of the blade shows large carbide teeth (not qui...

Read this review »


FastCap Gave Me The Finger ...

FastCap Gave Me The Finger ...

01-31-2015 12:19 AM by TheDane | 35 comments »

... and I like it! A few weeks ago, I responded to a promotional email from FastCap and they sent me their new ’11th Finger’ for free. Some people here on LJ’s scoffed at it, but I actually kind of like it. It stands within easy reach on my saw’s fence or the table, and works as well as any other push stick I have ever used. There is one downside … the two rare-earth magnets in the base are just friction fit and can come out if you mistakenly lay the ...

Read this review »


Top Saver works as advertised

Top Saver works as advertised

09-26-2009 07:27 PM by Bothus | 4 comments »

This is an excerpt from my blog posting about restoring my Unisaw. I thought it worked as a review. You can read the original/view the original post HERE. I would have given the product 5 stars except that while it worked much better than I expected in reality it is only as good as the amount of elbow grease you use with it. Enjoy! Where da hail did you get those glasses? You look like yo Aint Bea in Shreveport. Scrubbing away. .Top Saver first pass Top Saver 3 Honey! Top Save...

Read this review »


Leecraft Phenolic Insert GE-3

Leecraft Phenolic Insert GE-3

05-25-2009 04:27 PM by Chris | 16 comments »

Purchased this insert from Woodcraft in Jacksonville for a couple of reasons; first and foremost it was cost effective. Secondly, I have had little luck making my own from plywood or other such materials due to the fact that I can’t tweak the height (no leveling screws). The first pic shows the insert alongside the factory supplied insert from General. There is a screw on one end and one side to adjust the lateral fit and small hex screws at the four “corners” to adjust t...

Read this review »


Freud LU85 Ultimate Cutoff Blade - an accurate name

Freud LU85 Ultimate Cutoff Blade - an accurate name

11-29-2012 03:22 AM by Class1E | 9 comments »

I purchased this blade to replace the OEM blade on my G0690 table saw. As i was cutting the kerf in my crosscut sled, I noticed that the OEM blade was wobbling very slightly. I decided it was about time to replace that blade with two dedicated blades, one for rip cuts, the other for cross cuts.This was the blade I purchased for cross cuts. My first use for this blade was to trim the edges on my end-grain cutting board to square it up and remove the rough edges after flattening. I used the...

Read this review »


simply amazing!

simply amazing!

10-26-2011 03:33 PM by slickSqueegie | 9 comments »

The good: I do believe this Miter gauge to be the best on the market! It is unbelievable accurate and very well built! The bar itself is completely adjustable for any miter slot. I get no wiggle or play at any point with this gem. after using it I am extremely confident with the positive stops. It has a ruler built into the miter gauge fence and a micro adjustable stop for repeating cuts for accuracy. It also has a stop built in at the very end of the telescoping fence for even more versatili...

Read this review »


Significant Improvement over SawStop Overarm Dust Collector

Significant Improvement over SawStop Overarm Dust Collector

11-08-2016 04:23 PM by jmos | 5 comments »

I recently purchased a SawStop 3hp PCS with the overarm dust collection. I replaced a Jet hybrid saw where I had upgraded the stock blade guard to a Shark guard and had been very happy with the results. I was hopeful the SawStop overarm dust collection would be as well designed, and operate as well as the rest of the saw. Unfortunately, it doesn’t. The SawStop overarm dust collection has a small hose that connects to it, and that narrows to nearly nothing as it goes into the blade...

Read this review »


milescraft feather board

milescraft feather board

02-02-2010 09:59 PM by kosta | 9 comments »

Yo whats up everybody I wanted to do a review of the milescraft fetherboard. Most people make their own feather boards but I use this feather board from milescraft and it works pretty good. The problem with the feather boards that people make is that its really hard to adjust them to different tools. This feather board is adjustable to 2 different size miter slots. You can adjust the feather board to work on most cuts. You can use this feather board on a router table, tablesaw, and a bandsaw.

Read this review »


The Ridgid digital miter gauge

The Ridgid digital miter gauge

12-02-2012 03:05 PM by garriv777 | 8 comments »

This will be my first review posted at this site and I felt I should share my experience with this tool because someone else left a glowing review and I just had to let people know that this same tool was not at all the quality tool that I thought it was going to be. Maybe I just got a bad one or something but the following is my account of the quality of this tool: I purchased this tool online at the HD website along with a Bosch router. The packaging was fine, no damage at all and I was ...

Read this review »


solid digital gauge which requires user modification to properly function!

solid digital gauge which requires user modification to properly function!

10-28-2008 08:15 AM by Michael Hacker | 5 comments »

i was in the market for a miter gauge and found myself looking at this beauty in a recent email from Hartville Tool. i decided to give it a go and happily sent off my $59.99 + S&H and awaited its arrival. shortly the package arrived and upon initial inspection i was very happy, the gauge looked well made, hefty, and simple, exactly what i was expecting! then i decided to assemble it… and that is where the problems began! the handle wouldn’t thread into the guide rail sec...

Read this review »


« prev 1 ... 9 10 11 12 13 14 15 ... 21 next »
207 reviews

Add new review
View Product Index
RSS FEED

Browse reviews

categories | brands | all reviews


DISCLAIMER: Any posts on LJ are posted by individuals acting in their own right and do not necessarily reflect the views of LJ. LJ will not be held liable for the actions of any user.

Latest Projects | Latest Blog Entries | Latest Forum Topics

HomeRefurbers.com