LumberJocks

Reviews: Tablesaw Accessories

  • Advertise with us
New And Improved Stumpy Nubs Box joint Jig

New And Improved Stumpy Nubs Box joint Jig

08-17-2014 11:43 PM by fl13 | 9 comments »

Recently I purchased plans from the Stumpy Nubs Website for his improved Box Joint jig. $10.00.I spent the better part of a Saturday putting it together despite some confusing instructions, not a big deal, still managed to construct a working jig, just using the photos .I have built other jigs in the past and have constructed a few Beehives . (bees have a way of fixing sloppy joints), still I wanted to construct some small boxes with tighter and more accurate joints.This jig does the trick. S...

Read this review »


Accuracy is Art

Accuracy is Art

01-25-2008 04:14 AM by Bruce | 18 comments »

Greetings from West Virginia. I’m new here but I have been dying to tell someone about my new toy. I just got the Osborne EB3 Miter Gauge for Christmas and its great! I have a Grizzly G0576 left tilt table saw and the stock miter gauge was ok for rough cuts but it just was not accurate enough in my judgement. Even though I adjusted the guide bar, it still would move slightly in the slot. The angles were difficult to set and I had to look for my protractor to double and triple check...

Read this review »


Osborne Miter guage for your table saw

Osborne Miter guage for your table saw

05-13-2009 01:36 AM by Bob #2 | 28 comments »

I had looked at this guage before and had purchased an alternate one in the interim. (shoot me) I got a chance last week to re evaluate it and have these observations: 1. It uses triangulation rather than depending on a pivot point on a miter guage. What this means is that where a miter guage can get you close, the triangle can get you dead on.It’s just got more room on the scale to get it right. The extendable arm has a series of detents on the underside (20 in all) that gets you...

Read this review »


Grizzly 6" cast iron hand wheel

Grizzly 6" cast iron hand wheel

06-06-2015 04:27 AM by athomas5009 | 10 comments »

I ended up picking up a cpl of these to replace the garbage plastic OEM ones on my Cman 113 saw. I was a little lerious whether they would work because I ran across a few unhappy reviews because of difficulties modifying the fit. Well they arrived today and I couldn’t be happier! The are nice stuffy and turn real smoothly. Installation was a breeze and I don’t see why some would complain. As long as you have a drill press just bore the center hole to 1/2” then pop a 1/4&#...

Read this review »


Micro Jig SteelPro Splitter - for 1/8" Kerf Blades

Micro Jig SteelPro Splitter - for 1/8" Kerf Blades

02-02-2010 05:41 PM by PetVet | 17 comments »

You can purchase this product from Incra for about $35. I was interested in getting a splitter that I would use, as my rip guard/splitter was a pain to install every time I wanted to rip something.It comes as a kit, with an installation jig, and several splitters of various widths. The instruction sheet was fairly easy to follow. You need a couple pieces of 1/2 inch stock, one for the jig to attach to, and one as a test piece. They have you drill the holes in your saw insert with the prov...

Read this review »


Finesse Table Saw Alignment with PALS

Finesse Table Saw Alignment with PALS

06-04-2010 08:37 AM by Jack Barnhill | 12 comments »

The “Contractor Saw Precision Alignment & Locking System” (PALS™) from IN-LINE INDUSTRIES is just that, an alignment upgrade for a contractors table saw. It provides a significantly easier and more precise way of aligning the table saw blade to the miter slot than the manufacturer’s suggested method of pounding on or prying on the trunnion. PALS consists of 2 each threaded studs, flat washers, nuts, lock nuts, L-brackets with adjustment screws and lock nuts, and 1 Al...

Read this review »


120 Teeth that make me smile!

120 Teeth that make me smile!

08-14-2011 10:26 PM by JasonWagner | 10 comments »

I bought this “Oshlun 8 dado stack after watching it on Amazon for more than a year. Usually I’m not really cheap but I knew the price would drop eventually. I got it for $55.93 in 04/10 with free shipping and no tax. That’s a lot of C4 carbide for the price. I have two Forrest WWII blades and used to have a Freud 6” dado stack for a contractor saw. This blade set is awesome for the money. This blade stack will give very small “bat wings” in the bot...

Read this review »


IN-LINE INDUSTRIES PP2325 Machined Steel Pulleys

IN-LINE INDUSTRIES PP2325 Machined Steel Pulleys

08-12-2010 07:43 PM by ChuckC | 11 comments »

I have a Craftsman 10” contractors table saw that I bought new about 6 years ago for just over $500. I am a hobbyist woodworker and the saw suits my needs. Recently the saw developed a really bad vibration and loud rattle. I took a look at everything using a dial indicator and everything checked out. There was favorable review in Wood magazine a few years ago regarding this product so I thought I would give it a try. I wanted the pulleys and link belt which was $50 shipped. They told me...

Read this review »


Overhead Dust Collection for the Tablesaw

Overhead Dust Collection for the Tablesaw

12-13-2010 03:17 AM by ChunkyC | 1 comment »

I ordered the Dust Collecting Blade Cover (DCBC) sold by Bob Ross from The BORK Store. I think this is a fairly new product from Bob as he literally designed it to my specifications. His original design called for a 2-1/4” hose but that size of hose is hard to connect to a fixed dust collector. I asked him if he could make it to fit 2-1/2” hose and that I was planning on mounting it to 2” sch40 PVC pipe. One other thing that Bob did for me was to make the arms a little l...

Read this review »


magic molder is great

magic molder is great

01-02-2011 12:56 AM by dub560 | 1 comment »

now, i’m by no means am I a professional but the results on this thing i think is exceptional. very little sanding if any at all , quick and easy plugs changes, and the ease of use on the table makes it a winner. first off i only have a portable table saw but i tell ya brothers the saw never bogged down at all when i was feeding mahogany,oak or walnut through as i was making some profiles—just pure experimentation by the way. the plugs are not cheap but they work very well̵...

Read this review »


« prev 1 2 3 4 5 6 ... 18 next »
178 reviews

Add new review
View Product Index
RSS FEED

Browse reviews

categories | brands | all reviews


DISCLAIMER: Any posts on LJ are posted by individuals acting in their own right and do not necessarily reflect the views of LJ. LJ will not be held liable for the actions of any user.

Latest Projects | Latest Blog Entries | Latest Forum Topics

HomeRefurbers.com