LumberJocks

Reviews: Tablesaw Accessories

  • Advertise with us
A Riving Knife Solution!

A Riving Knife Solution!

11-25-2010 07:06 PM by ChunkyC | 7 comments »

Ease of installation 4 StarsAdjustability: 4 StarsEase of Setup: 3 StarsCustomer Service 4+ Stars The BORK (Bolt On Ripping Knive) is sold by Bob Ross and is available from The BORK Store The asking price is $115. I learned about the BORK from, where else, here at LumberJocks from a review by KnotScott. Since knotscott already has a full review, I’ll just give my impressions and experiences. Tools used: 5/16” socket w/ 1/4” drive ratchet, straight screw driver, a...

Read this review »


Problems and fixes

Problems and fixes

02-21-2013 10:41 PM by captferd | 7 comments »

One problem is that because its made of 2 pieces of plastic glued together it will break apart at the seam. You can try to glue it back together but it soon comes apart again. (This is an update 40 days after the first post. Walmart sells a 3pk of generic super glue for 89 cents. I glued it up and clamped it lightly over night. It seems to be holding up fine.) Other than that, I love this thing. It will move the fence thousandths at a time, allowing you to sneak up on a precise cut. If ...

Read this review »


The SawStop ICS base is wonderful saw base, but comes just short of 5*

The SawStop ICS base is wonderful saw base, but comes just short of 5*

05-13-2013 03:22 PM by gtbuzz | 7 comments »

OverviewIn short, this is an absolutely wonderful base that I love using with my SawStop 3HP cabinet saw, however I do have a few nits that keep this from being a 5 star product. Having said that though, if anyone else is in a similar situation to me, I wouldn’t hesitate for a second to recommend the industrial base over the standard professional base. For those that are unaware, SawStop makes two different mobile bases for their cabinet saws, one designed for the Professional models...

Read this review »


HTC 37" x 31" Folding Roller Outfeed Table for Table Saws - HOR-1038U

HTC 37" x 31" Folding Roller Outfeed Table for Table Saws - HOR-1038U

12-28-2013 07:01 AM by darthford | 7 comments »

My 3 car garage is limited on space due to multiple machines and the tractor/lawn equipment eating up one whole bay so I decided to go with this fold down roller outfeed table on my new Grizzly 12” G0696X table saw. The concept works perfectly for me, its attached to the saw so its mobile, setup takes 5 seconds, love that. Lets take a picture tour and I’ll offer some additional comments. Packing FAIL but thankfully no damage, you can see some of the rollers spilled out into the...

Read this review »


Bosch 4100 left and rear extensions

Bosch 4100 left and rear extensions

05-18-2014 03:29 AM by Holbs | 7 comments »

Wish I had known about these accessories sooner! For the last year, using the bosch 4100 table saw has been great, but these support extensions make me feel much more safer. These 2 extensions are a must have for the few left out there that use the bosch 4100. Granted, these supports do not replace TRUE structure table outfeed supports but for what it is, they are highly acceptable and affordable ($27 each?).

Read this review »


After Market Table Saw Splitter, Shark Guard

After Market Table Saw Splitter, Shark Guard

08-15-2014 06:29 PM by woodshopmike | 7 comments »

Worried about kickback on your table saw? Who isn’t really? Most if not all modern saws arrive with either a splitter or riving knife that prevents wood from pinching the back side of a table saw blade as the stock is run through the saw. This little piece of material pays dividends in preventing kickback. So if most saws come with such a device already installed, why write a review about an after market product? Because if you’re like me, you use vintage machinery. In my case...

Read this review »


SawStop zero clearance throat plate with changeable inserts

SawStop zero clearance throat plate with changeable inserts

10-04-2014 10:08 AM by Tim_H | 7 comments »

So I finally bit the bullet and purchased a SawStop table saw. After doing so I searched to find a zero clearance plate. Of course SawStop offers zero clearance plates at about $40 ea but I found this one from Infinity Tools that cost $100 but offers changeable inserts that are low cost so I just had to buy one plate and several “inserts” to accommodate the many different blades and angles that I end up using. Purchasing an entire new plate for each blade and each angle of each bl...

Read this review »


One of the best ideas

One of the best ideas

10-21-2014 02:19 AM by ic3ss | 7 comments »

I’ve been looking at these for about a year and finally pulled the trigger last week. I had a kickback incident that smashed a couple of fingers last year and since then I’ve had my mind on ways to make my old Unisaw safer. This has got to be one of the best safety devices for the woodshop in many years. What it does is so basic its a wonder it has only recently been made commercially. It’s an expensive device to be sure, at $80. For me it took a few smashed fingers to ge...

Read this review »


Rockler Sure-Loc Miter Guage With Fence & Stop

Rockler Sure-Loc Miter Guage With Fence & Stop

03-17-2008 04:53 PM by DaveH | 6 comments »

Dead on accurate out of the box if your miter slots are parallel with the saw blade. Easy to assemble and adjust. Price paid: $101.49 ( included shipping ) Would I buy another: No, spend the extra money and get a better quality solution or build you own. I’m going to replace the fence with a shop built. Rockler Link Improvements needed:Option for a fence extension.Flip stop instead of a wood sliding stop.Drop in miter bar style instead of a bar style forcing you to slide...

Read this review »


Improved splitter for my Saw

Improved splitter for my Saw

01-22-2009 12:03 AM by marcb | 6 comments »

I have an older saw with a horrible splitter. I’ve often gone without or used one of those cheap snap in plastic things for ZCI if I had to have one for serious ripping. This all changed with a piece of knowledge, part number 1349941 from the Delta parts website. This easily installs into Delta saws (even my old Rockwell) and someone made a website about installing it onto a jet. The splitter is thick, so it is not for use with thin blades. A knurled nut makes it easy to rem...

Read this review »


« prev 1 ... 10 11 12 13 14 15 16 ... 18 next »
171 reviews

Add new review
View Product Index
RSS FEED

Browse reviews

categories | brands | all reviews


DISCLAIMER: Any posts on LJ are posted by individuals acting in their own right and do not necessarily reflect the views of LJ. LJ will not be held liable for the actions of any user.

Latest Projects | Latest Blog Entries | Latest Forum Topics

HomeRefurbers.com

Latest Projects | Latest Blog Entries | Latest Forum Topics

GardenTenders.com :: gardening showcase