LumberJocks

Reviews: Tablesaw Accessories

  • Advertise with us
Begininng with the Installation of the EEZE FEED infeed table

Begininng with the Installation of the EEZE FEED infeed table

12-27-2014 07:48 PM by psient | 0 comments »

I was on You Tube looking for someone’s experience installing Lee Jesberger’s EEZE FEED infeed tablesaw table. I did not find any videos capable of helping my installation. Here, I’ve started to describe my own installation as a review and something of a guide for others. I’ll be installing the EFIT on my powermatic PM3000 7 HP table saw: http://www.powermatic.com/Products.aspx?Part=1720305K I purchased the saw several years ago. This was as much a health deci...

Read this review »


Out of box near perfect

Out of box near perfect

12-05-2014 06:11 PM by dozer57 | 8 comments »

Incra 1000hd with no adjustment is near perfect on angles. I am new to segmented turning and my miter fence for my craftsman table saw was junk, Three stops and sloppy fit in the track, never able to repeat angles. I would have to sand each piece to get a fit that I was happy with. NO more ordered Incra 1000hd from Amazon.com took it out of the box and installed it on the table saw with only adjustment made to T-track. First thing noticed was how smooth the track slid in the slot. Miters were...

Read this review »


One of the best ideas

One of the best ideas

10-21-2014 02:19 AM by ic3ss | 7 comments »

I’ve been looking at these for about a year and finally pulled the trigger last week. I had a kickback incident that smashed a couple of fingers last year and since then I’ve had my mind on ways to make my old Unisaw safer. This has got to be one of the best safety devices for the woodshop in many years. What it does is so basic its a wonder it has only recently been made commercially. It’s an expensive device to be sure, at $80. For me it took a few smashed fingers to ge...

Read this review »


Incra miter gauge very good, but it takes a bit of work

Incra miter gauge very good, but it takes a bit of work

10-13-2014 04:51 AM by ic3ss | 23 comments »

So I finally took the plunge and ditched my miter gauge that came with my old Unisaw. I never really used it, it just sat there if needed. Well, I knew from experience that it was crap so it has gone away. Bought the 1000HD a while back and have been using it for a few weeks and man am I impressed. This is what Made in USA is all about. I’ve been loving everything about it, but it took a bit of work. I picked it up at Rockler on sale for $119. First off, the thing is packaged ver...

Read this review »


My tenon making solution

My tenon making solution

10-09-2014 01:33 AM by CharlesA | 4 comments »

I’ve made tenons using several different methods. I had avoided buying a tenoning jig because it seemed like an unnecessary outlay of funds. I could make them by hand, with the bandsaw, or using a dado blade on the table saw. But for whatever reasons, I always have been a little frustrated by how they came out. I ended up doing way too much fine tuning with chisel/plane/sandpaper. So, I bit the bullet and purchased the Grizzly tenoning jig through Amazon, $88.59. I was annoyed...

Read this review »


SawStop zero clearance throat plate with changeable inserts

SawStop zero clearance throat plate with changeable inserts

10-04-2014 10:08 AM by Tim_H | 6 comments »

So I finally bit the bullet and purchased a SawStop table saw. After doing so I searched to find a zero clearance plate. Of course SawStop offers zero clearance plates at about $40 ea but I found this one from Infinity Tools that cost $100 but offers changeable inserts that are low cost so I just had to buy one plate and several “inserts” to accommodate the many different blades and angles that I end up using. Purchasing an entire new plate for each blade and each angle of each bl...

Read this review »


Magic Molder—A Safe and Professional Molder Head System

Magic Molder—A Safe and Professional Molder Head System

09-15-2014 03:46 AM by HillbillyShooter | 23 comments »

The Magic Molder System consists of a molder head and cutter plugs. Although not inexpensive, Magic Molder constitutes a truly safe and professional system for using your table saw (or radial arm saw if so inclined) as a shaper for cutting molding profiles. There are three primary features that make this system head and shoulders above the previous molder head I acquired 30 plus years ago—one I’ll humorously describe as a “cubby, Ninja star.” First, the Magic Molder is the safest des...

Read this review »


New And Improved Stumpy Nubs Box joint Jig

New And Improved Stumpy Nubs Box joint Jig

08-17-2014 11:43 PM by fl13 | 6 comments »

Recently I purchased plans from the Stumpy Nubs Website for his improved Box Joint jig. $10.00.I spent the better part of a Saturday putting it together despite some confusing instructions, not a big deal, still managed to construct a working jig, just using the photos .I have built other jigs in the past and have constructed a few Beehives . (bees have a way of fixing sloppy joints), still I wanted to construct some small boxes with tighter and more accurate joints.This jig does the trick. S...

Read this review »


After Market Table Saw Splitter, Shark Guard

After Market Table Saw Splitter, Shark Guard

08-15-2014 06:29 PM by woodshopmike | 7 comments »

Worried about kickback on your table saw? Who isn’t really? Most if not all modern saws arrive with either a splitter or riving knife that prevents wood from pinching the back side of a table saw blade as the stock is run through the saw. This little piece of material pays dividends in preventing kickback. So if most saws come with such a device already installed, why write a review about an after market product? Because if you’re like me, you use vintage machinery. In my case...

Read this review »


General Int. 50-050 Tenoning Jig

General Int. 50-050 Tenoning Jig

07-08-2014 08:59 PM by Crickett | 10 comments »

I keep harping on efficiency being a major consideration in any tool I consider buying, and with the handful of tenoning jigs out there, I didn’t know where to turn. What I found blatantly obvious were the various brands (Delta, WoodTek, Shop Fox, Grizzly, Rockler, etc.) are all the same tool with different paint/logos. So that left the General and Jet as the top two contenders. I’m talking about “new” tenoning jigs here, but I suspect a few comments on older jigs. I c...

Read this review »


1 2 3 4 ... 17 next »
167 reviews

Add new review
View Product Index
RSS FEED

Browse reviews

categories | brands | all reviews


DISCLAIMER: Any posts on LJ are posted by individuals acting in their own right and do not necessarily reflect the views of LJ. LJ will not be held liable for the actions of any user.

Latest Projects | Latest Blog Entries | Latest Forum Topics

HomeRefurbers.com

Latest Projects | Latest Blog Entries | Latest Forum Topics

GardenTenders.com :: gardening showcase