LumberJocks

Reviews: Router Accessories

  • Advertise with us
well worth the money..........

well worth the money..........

12-15-2013 04:14 AM by pastaamann | 5 comments »

i got this system about 2 months ago,and its everything they say and more.very self explanatory,simple to operate and very precise.i would recomend this system to anyone that can get one to not hesitate,just get it and you will be so very happy you did.the 90 min. video tells you everything you need to know and the large referance guide is simple to use.i tried to make the three differant double dove tail and corner post joints and they went together without a problem.easy to install ,great h...

Read this review »


A very accurate safety device.  A Must Have!

A very accurate safety device. A Must Have!

11-27-2013 02:52 AM by MHarper90 | 14 comments »

The Purpose: So I do most of my woodworking at work because we have a pretty nice shop there. In late September of this year I was routing a 1/2” deep x 2” wide flute into a piece of wood when the workpiece was shot across the room and my left hand was thrown into the router bit. After a trip to the ER and emergency hand surgery with a skin graft, I was very fortunate in that I only lost 3mm of bone and approximately 5mm of total length off of the end of my left thumb (I st...

Read this review »


Solidly built, great case.  Nothing cheap and plasticy about this

Solidly built, great case. Nothing cheap and plasticy about this

10-29-2013 02:49 AM by zzzzdoc | 4 comments »

Typical Woodpeckers solid device, here. It’s a corner jig for rounded corners, as well as a chamfer jig for corners. There are 12 different sizes for rounded corners, from 1/4” to 1-1/2”, and 6 different sizes for chamfered corners, from 1/4” to 1-1/2” The jig is solidly milled out of aluminum, with generous tabs for clamping to your workpiece, as well as a solid stable surface for your router to rest on. I was able to easily rout corners in a variety o...

Read this review »


You get what you pay for

You get what you pay for

10-29-2013 12:52 AM by laketrout36 | 7 comments »

Here’s a set I received as a gift. Most of the bits I have yet to use. A few have been used a few times. If you are only going to use these bits at most a few times each and not demanding great results then OK. But if you need quality results and don’t want to play games with something just to use it then pass on them. The case they come in is durable and each bits location is labeled with an image of the bit shape so that is a positive. The second picture I included shows...

Read this review »


Whiteside Oval Edge Bit

Whiteside Oval Edge Bit

10-29-2013 12:31 AM by laketrout36 | 4 comments »

A new project called for a new router bit. Many members here on LumberJocks hold Whiteside router bits in high regard. This is the second Whiteside router bit I’ve bought this year and am once again completely satisfied with it. I’m currently making a small rustic cabin with log siding as a presentation/display/gift box. The Whiteside oval edge bit # 1476 is a 1/2” shank, 3/4” bead opening and met my requirements. Tonight I put it in the router and fed one board p...

Read this review »


Whiteside 3362 Lock Miter router bit

Whiteside 3362 Lock Miter router bit

09-29-2013 12:26 PM by Mark Colan | 39 comments »

I wrote a review on Amazon for the Whiteside 3362 Lock Miter router bit.

Read this review »


Rockler Coping Sled

Rockler Coping Sled

09-27-2013 05:21 AM by Albe | 6 comments »

I have never wrote a tool review but after using Rockler’s Coping Sled and not seeing any other reviews I figured I’d try my luck. I actually bought the copping sled several years ago when I got frustrated when using a rail and stile bit set to do the profile on the end grain. No matter how hard I tried bit seemed to grab and it threw it off track. I again realized how much of a lifesaver it is when using it again doing the same operation. Although the copping sled seems a little steep ...

Read this review »


Valfor Tools Bit Vise -- Router Bit maintenance and sharpening.   ( $69.95 )

Valfor Tools Bit Vise -- Router Bit maintenance and sharpening. ( $69.95 )

09-12-2013 11:59 AM by philphoto | 9 comments »

The need for the bit vise is at first glance, not exactly obvious. Many if not most woodworkers are less than diligent with maintenance and sharpening their bits and tools. It is of importance to note that a casual woodworker may not spend big dollar amounts on their bits, however all bits should be cleaned and sharpened, to operate as designed. The casual woodworker may not be aware of the need for maintenance, and some woodworkers just throw the dull bit away. As a retired professional ...

Read this review »


Leigh VRS - the VRS24 exactly

Leigh VRS - the VRS24 exactly

09-11-2013 03:53 PM by ken_c | 6 comments »

I purchased the VRS attachment for my Leigh jig a while ago but hadn’t needed to make any dovetails for a while – until now – The vacuum attachment is well worth the $100. I estimate dust collection now at about 98%. I would highly recommend anyone with a Leigh jig pony up the extra cash and get that attachment. Mine is hooked up to a 4” port on the central dust collection but gets reduced to a 2 1/4” hose at the jig. That provides a fairly low air speed for...

Read this review »


The MLCS Multi Joint System

The MLCS Multi Joint System

09-10-2013 10:09 AM by Blackie_ | 5 comments »

As a new adventurous into box joint, joinery and after study and research I optioned for the router table version The MLCS Multi Joint System as for me swapping out a router bit is much more to my liking apposed to swapping out a tablesaw blade plus it’s easier and leaves a cleaner cut. I’ve had this system for a good bit and after trial and error during the learning phase, I now have a good grasp on how it works, am pleased with how it preforms, it’s ease in use and ready t...

Read this review »


« prev 1 2 3 4 5 6 ... 14 next »
136 reviews

Add new review
View Product Index
RSS FEED

Browse reviews

categories | brands | all reviews


DISCLAIMER: Any posts on LJ are posted by individuals acting in their own right and do not necessarily reflect the views of LJ. LJ will not be held liable for the actions of any user.

Latest Projects | Latest Blog Entries | Latest Forum Topics

HomeRefurbers.com