LumberJocks

Reviews: Dust Collection

  • Advertise with us
Not a very good value

Not a very good value

02-06-2012 01:32 AM by MoshupTrail | 32 comments »

I picked this up on sale from Rockler recently and put it together this weekend. First off, the box it comes in is very small. In fact, it looks tiny next to my 16 gal Ridgid vac. The Vortex comes in two halves allowing it to nest inside the carton. Clever packing. I was afraid it might leak at the joint, but it proved to be a nice tight fit. Assembly: Not hard at all. The directions are clear and well written, but… There are two connectors for the intake and out...

Read this review »


Dissapointed

Dissapointed

11-21-2011 07:27 AM by exelectrician | 35 comments »

I am dissapointed with my Delta 50-760 for the following reasons…1. It is too loud.2.It cannot pick up more than ten handplane shavings with out blocking all the grids inside.3.I cannot use it anywhere near my chopsaw, small offcuts have caused several dents in the case when they slam into the inner parts.4.I touch the large fabric bag and a cloud of fine dust falls, Am I breathing this stuff?

Read this review »


upgrading HF dust collector to cyclone with Grizzly and Wynn

upgrading HF dust collector to cyclone with Grizzly and Wynn

05-18-2016 12:49 PM by playingwithmywood | 10 comments »

Ok First if you have not bought a dust collector do not do this project instead go ahead and buy the biggest cyclone system you can afford because if you are like me your tools will grow and you collector will become too small Like many I started with a HF collector and put in the home-aid Thein baffle and a Wynn filter when I first started out This was good until I got a bigger joiner and more tool but I always hated the bag and the fact that all the chips were going thru the impell...

Read this review »


Laguna 2HP review

Laguna 2HP review

02-09-2015 04:20 PM by MrSammy | 29 comments »

My wife purchased the 2 HP Laguna Dust Collector for me. I was always hesitant on buying Laguna because of their horrible customer service reviews. I currently have a 14/12 band saw and have had zero problems. I will explain the problems I experienced and explain why I will never purchase a Laguna product ever again. My wife bought me the 2 HP Dust Collector because I do woodworking to cope with my Post Traumatic Stress Disorder. She copes with my drinking from doing and experiencing e...

Read this review »


Impressive for a small shop

Impressive for a small shop

01-24-2017 12:50 AM by ColonelTravis | 26 comments »

I work out of a 2-car garage that can barely hold one car because it’s filled with woodworking crap, and it’s a brand new car so I don’t want it constantly covered in sawdust, nor do I want the rest of the garage covered in sawdust, which is how it’s been for a while. I use mostly hand tools but I have a bandsaw, miter saw, sanders, etc. and my dust collection system is just me with a leaf blower out an open garage door. So I bought this thing off amazon for about $...

Read this review »


Oneida Super Dust Gorilla - 5 HP

Oneida Super Dust Gorilla - 5 HP

07-29-2016 12:42 PM by Redoak49 | 10 comments »

Several months ago, I purchased a new dust collector. Before, I had a Jet 1.5 HP dust collector with a cartridge filter and vortex cone. It did an OK job and was piped into my shop with 4” PVC. My measurements of the flow at the dust collector were 670 CFM at the 6” port and only 450 CFM at the 4” port. The maximum static pressure was 10.25” Inside my shop, the flow was greatly reduced. I decided that I needed something bigger to collect more of the dust and so looked at a number of t...

Read this review »


dustcutter II dust collection system paired up with ridgid TS3650

dustcutter II dust collection system paired up with ridgid TS3650

09-04-2013 04:44 PM by yrob | 3 comments »

I have a small shop and use a Ridgid TS3650 contractor style table saw. Dust collection has always been a problem. I have tried enclosing the saw with hardboard pieces in the past but this makes it impossible to tilt your blade as the motor sticks out. I recentlly bought this product, the Dustcutter II from Woodcraft. It is basically a dust bag shaped like a funnel with a 2 1/4” port at the end. It attaches to the table saw from the inside by velcro. The installation guide say...

Read this review »


Oneida Dust Deputy Cyclone

Oneida Dust Deputy Cyclone

08-24-2016 02:19 AM by richimage | 18 comments »

The SDD replaces a “Frankenvac” HF through a Thein separator to a plastic barrel, using Rockler quick-connects to each tool. I replaced the HF impeller with the Rikon, and what a difference! I am blessed to be able to just vent outside, so fine filtration is not a concern. The assembled collection corner is amazingly quiet, and has quite a lot ( don’t have the ability to measure airflow) of suction – even on the far end where the SawStop lives. I read of so...

Read this review »


Great cyclonic dust separator

Great cyclonic dust separator

05-29-2012 02:49 AM by Alexandre | 10 comments »

The dust deputy is a great dust separator for my Ridgid shop vac.I gave it 4 stars out of 5 because for a few reasons:1. It’s really unbalanced without a cart when you move it2. Its pretty awkward moving it unless you build a cart.3. Static electricity during dry times is a pain and a hassle as some dust gets in because it tends to stick to the cyclone.4. The container fills up quickly, probably a 35 gal drum would be nice.5. The price is pretty high for a piece of moulded plastic and 2...

Read this review »


Do not buy at this time, manufacturing error

Do not buy at this time, manufacturing error

03-12-2013 02:48 PM by asloanie | 43 comments »

I recently bought one of these, returned it, and now am about to return the replacement. The unit comes with a mounting platform and casters. They must have recently changed caster manufacturers as the new ones do not line up with the pre-drilled holes in the metal platform. Both units I got had this exact problem. If you want to use your own platform or drill new holes yourself, this still could be a usable system. Just an FYI. I would recommend opening the small box the caster...

Read this review »


« prev 1 ... 9 10 11 12 13 14 15 ... 23 next »
225 reviews

Add new review
View Product Index
RSS FEED

Browse reviews

categories | brands | all reviews


DISCLAIMER: Any posts on LJ are posted by individuals acting in their own right and do not necessarily reflect the views of LJ. LJ will not be held liable for the actions of any user.

Latest Projects | Latest Blog Entries | Latest Forum Topics

HomeRefurbers.com