LumberJocks

LumberJocks Woodworking Reviews

  • Advertise with us
Yardstick style measuring compass

Yardstick style measuring compass

09-05-2009 06:26 PM by Bob #2 | 12 comments »

I saw this item during a small ordering spree with woodcraft and added it to my order givng it little thought as it was quite simple and what could go wrong? First thing is it was back ordered and shipped separately at a later date.That would be fine if I had been advised but there was nothing mentioned on the invoice so I assumed it had been overlooked and proceeded to buy another one locally ( different style but same application.) When this one arrived I at first tried it on the y...

Read this review »


Benjamin's Best Bowl Gouges

Benjamin's Best Bowl Gouges

10-18-2010 10:33 PM by Lochlainn1066 | 2 comments »

I have the 3/8 and 1/2 inch gouges from Penn State. As of the current catalog (got it today), they are $15.95 and $19.95. I am a self taught turner (about 5yrs experience), so my only comparison in edge retention is from a cheapo Harbor Freight set and an older Buck Brothers set. The BB gouges hold an edge as long or longer than any of these tools, which makes them about average for HSS. I have a high carbon scraper I made myself which doesn’t hold an edge very long at all, for co...

Read this review »


Replacing an old benchtop planer

Replacing an old benchtop planer

02-13-2011 08:14 PM by Ian_S | 7 comments »

I recently purchased ($1390.00) this planer from my local woodworking store Warren Cutlery in Rhinebeck New York. The planer was on display in the store, so all I had to do set up wise was bolt on the cast iron bed extensions, connect the dust collection hood and install a plug. Set up time under two hours. The adjustment screws on the bed extensions were easy to use when leveling the beds, though the screws on each end had limited room for turning the allen key. This planer appears to b...

Read this review »


ShopSmith Vs. Gator 3 X 21, 80 grit sanding belts. Price comparison.

ShopSmith Vs. Gator 3 X 21, 80 grit sanding belts. Price comparison.

01-28-2013 12:53 AM by MarkTheFiddler | 12 comments »

ShopSmith sells 4 3X21 Sanding Belts for $17.98 at LowesGator sells 5 3X21 Sanding Belts for $5.98 at Lowes Figure $4.50 for each ShopSmith Vs. $1.20 per Gator I used both belts to sand the aluminum oxide finish off hardwood flooring for use in a project. That is some very tough finish. I sanded until I had to apply downward pressure on the belt sander to get a bite. I stopped there. Mind you the flooring finish dulls out the sand paper very quickly. Take a look at this picture: ...

Read this review »


Better drill than I expected, serviceable impact driver, so-so radio

Better drill than I expected, serviceable impact driver, so-so radio

08-29-2014 11:47 PM by Dan Lyke | 8 comments »

This is not a brand I would have ever expected to have in my shop, but… From my Twitter stream, on April 30th 2014 I got a follow from @RIDGIDPower, and said I’d be an unlikely customer. Surprising me, they engaged! We sent email back and forth, their rep offered to send me a battery powered tool combo kit with a drill, impact driver, and radio. I actually declined, on the basis that I didn’t need another set of chargers and batteries in my shop, but by that point the box wa...

Read this review »


LS1013F SAW

LS1013F SAW

07-18-2008 07:33 PM by grumpygramps | 8 comments »

I HAVE USED ONE OF THESE SAWS FOR 4 YEARS. IT IS ONE OF THE VERY BEST. IT WAS RATED THE BEST 10 INCH SAW FOR 3 YEARS STRAIGHT. THIS YEAR THERE IS A SAW THAT WAS RATED HIGHER BUT IT COST 1200.00. SO, THIS YEAR ..08.. IT IS RATED THE BEST SAW FOR THE MONEY. I BELEIVE THIS SAW CAN BE SERVICED AT 2 DIFFERENT LOCATIONS HERE IN THE USA. THE SAW BLADE IS ALSO TOPS. IN A SHOP SITUATION YOU MAY WANT ONE SAW FOR ROUGH LUMBER AND ANOTHER FOR FINISH WORK.

Read this review »


Lightweight lever ratchet clamp

Lightweight lever ratchet clamp

03-20-2009 08:39 PM by Tony | 1 comment »

I recently purchased quite a few of these clamps – see my blog http://lumberjocks.com/topics/5240. These clamps are available in 200 mm (8”) and 250mm (10”), with a 80mm (3”) jaw length. I found the clamps to be more than adequate for light clamping. They are very easy to use especially on smaller items such as boxes, where a light touch may be needed with thinner materials are used, however they are equally at home clamping jigs to the table or machine. These cla...

Read this review »


Disappointment with JET DC-650A 1 Horsepower Dust Collector

Disappointment with JET DC-650A 1 Horsepower Dust Collector

01-18-2010 12:47 AM by Don Newton | 20 comments »

Fellow Jocks, After 25 years of injesting sawdust, a very foolish thing to do, a few months ago I took the plunge and purchased a Jet Dust Collector and AFS-400 Air Filtration System. The Air Filtration System works as it should, but in my opinion the Dust Collector has some design flaws that make me sorry I purchased it. The dust collector is small but should be adequate for my needs. My workshop is in my basement so space is critical and portability is desirable. The Jet DC-650A seeme...

Read this review »


Dewalt DCD970KL review

Dewalt DCD970KL review

02-14-2011 05:00 PM by phtools | 5 comments »

I bought this drill to replace my Dewalt DC925, which fell off a roof and landed in a big nasty mud hole, I just figured the drill was toast and ordered a new one, saved the 925 for salvageable parts. The DCD950 and the DCD970 are the EXACT same drill except the clutch ring, which is black on the 950 and silver on the 970. The difference is the batteries that are included 950 has the XRPs and 970 has the new NANO’s(lithium-ion). OK, back to the comparison Pros of the DCD970/950 VS. the ...

Read this review »


Ezee-Feed, One My Best Shop Investments

Ezee-Feed, One My Best Shop Investments

06-27-2011 09:24 PM by Ryan Bruzan | 6 comments »

I picked up a nice, 12’ long piece of red oak S4S for ripping down into smaller stock. I needed 12’ lengths, but I also realized how much control I did not have if I tried to feed the board into my table saw from 11’ away from the blade. I didn’t think about handling and ripping it in my small shop. I mean, I have the length, but I did not want to have to crawl under the long boards to puzzle the ripping process together. After pondering the process for a moment for...

Read this review »


« prev 1 ... 293 294 295 296 297 298 299 ... 392 next »
3913 reviews

Add new review
View Product Index
RSS FEED

Browse reviews

categories | brands | all reviews


DISCLAIMER: Any posts on LJ are posted by individuals acting in their own right and do not necessarily reflect the views of LJ. LJ will not be held liable for the actions of any user.

Latest Projects | Latest Blog Entries | Latest Forum Topics

HomeRefurbers.com

Latest Projects | Latest Blog Entries | Latest Forum Topics

GardenTenders.com :: gardening showcase