LumberJocks

LumberJocks Woodworking Reviews

  • Advertise with us
You should see the other guy . . .

You should see the other guy . . .

07-06-2011 11:14 PM by Alster | 7 comments »

I recently bought a box of these nails to assemble a five-board bench. I drilled small pilot holes just to keep the nails headed in the right direction. Tremont recommends a pilot hole about the diameter of the nail halfway to the tip, but mine was much smaller and did the job just fine. The nails are a joy to drive, but they are soft—softer than round shank nails you might find at the hardware store. This makes it easy to clinch them, if you want, but also makes it easy to bend them...

Read this review »


Traditional Woodworker chisels

Traditional Woodworker chisels

02-22-2011 06:05 PM by dbray45 | 7 comments »

I purchased 6 chisels of this set. I was looking for a set of chisels that were in inches and not metric conversion like most of the chisels out there. My current set of Marples/Irwin/blue handled chisels have been good to me but are not real hard and keeping them sharp has been an issue. So, I bought the 1/8, 3/16, 1/4, 3/8, 1/2, and 5/8” chisels since these were the sizes that I will use the most. The way they are labeled is also nice and readable. These chisels, like all the r...

Read this review »


3M Microfinishing Film for tool sharpening

3M Microfinishing Film for tool sharpening

09-20-2012 06:33 AM by Purrmaster | 7 comments »

I bought this stuff from Tools for Working Wood a couple of months ago and have been using it since: http://www.toolsforworkingwood.com/store/dept/THS/item/ST-MAF.XX/3M_Micro_Abrasive_Film__for_Scary_Sharpening_-_PSA This finishing film from 3M is used in place of sandpaper for Scary Sharp. The grit of these are measured in microns. Tools for Working Wood has an article that gives a rough equivalency to the water stone grits. I.e. 1 micron is equivalent to a 1,000 grit stone. Please...

Read this review »


JDS Company 750ER Air Filtration System

JDS Company 750ER Air Filtration System

10-30-2010 08:59 PM by glassyeyes | 7 comments »

This is a VERY PRELIMINARY rating, since I only acquired this in the past few weeks. I couldn’t decide between 4 stars and 5, for the minor reasons noted below. I can’t speak to longevity, obviously. After a serious round of allergies, I thought I’d better do something about the dust in my shop. I chose this air filter in part based on various reviews on several sites, including Lumberjocks, and on advice from the staff at Woodcraft in Leesburg, VA. Another factor was t...

Read this review »


So far....What a Disappointment.

So far....What a Disappointment.

11-01-2010 05:04 AM by Routerisstillmyname | 7 comments »

About near two decades ago, I purchased a Dowel-it 1000 which I’ve used almost on every other project.It was made in USA and 100% accurate. And it’s held up to a half a dozen drops and what have you with just slight calibration after all these years. Awesome jig. Behold the new so called USA made dowel-it 2100. it has a 6 inch capacity and Two removable bushing screws with 1/4”, 5/16”, 3/8” sizes two each. and the 7/16 and 1/2 are permanent. I purchased this for a pro...

Read this review »


Great Tool for some tasks

Great Tool for some tasks

02-26-2015 03:37 PM by OnhillWW | 7 comments »

I have been using my Flatmaster drum sander (http://stockroomsupply.ca/shop/drum-sanders/18-flatmaster.html) for 2 years now and thought that I had something yet to add to the previous reviews for this product. Set-up:I purchased my Flatmaster complete with the metal top sans the motor; married it with a NIB – OS Dayton motor. Assembly and motor installation / setup was straight forward and easy enough. That said I had interference between the belt and my housing, the opening in the h...

Read this review »


J-B Weld KwikWeld - 6 minutes to setup

J-B Weld KwikWeld - 6 minutes to setup

08-25-2015 03:38 PM by Mike | 7 comments »

Hi All; So many of us have used the standard 25 minutes J-B Weld that well takes 25 minutes to cure. As many people know, that is a long time to keep something clamped and it usually in my experience takes a few hours to actually cure. The other day I had to make a repair to my car and I went into the big Orange box to pick up some J-B Weld. I came across the 6 MINUTE J-B Weld KwikWeld. I’d never seen it before (might have been out for years, I don’t know). I personally di...

Read this review »


RTJ-400 Dovetail Jig review

RTJ-400 Dovetail Jig review

03-05-2016 02:26 PM by Jarrhead | 7 comments »

Working on a dresser for my daughter. I decided to do the drawers with dovetail joints. Let me preface with what I am about to say with the facts that I never owned a dovetail jig, and I have never cut dovetails by hand. I have a very close friend who has a Rockler dovetail jig, and he graciously offered to let me use it. Meanwhile, I kinda had my eye on purchasing the Leigh RTJ400 jig. Well the dresser project got around to the point where I had to get to work on the drawers, but I hadn...

Read this review »


The Little Victor Plane from Lee Valley

The Little Victor Plane from Lee Valley

02-29-2008 03:15 PM by rikkor | 7 comments »

I bought this little plane mostly on a whim. I am simply amazed by how useful it has turned out to be. It is easy to use either one or two handed. It has Lee Valley quality throughout. The iron was very sharp when I got it. It has a cast iron body that just feels right. I believe the current price is about $35.00.

Read this review »


Fantastic Machine

Fantastic Machine

04-04-2012 03:41 PM by reggle | 7 comments »

After looking around for a while i decided to opt for the AWVSL lathe.This is a graet lathe i have no problems with it yet.you get 440mm (17”) between centres or with the optional bed extension 965mm (38”).the Max Diameter over Bed is 240mm (9.45”).the only problem i have is the speed only gets as low as 650rpm bit to fast when turning big logs.apart from that its a great bit kit Key features Constructed from cast ironPowerful 375W(1/2hp) DC permanent magnet motorElec...

Read this review »


« prev 1 ... 291 292 293 294 295 296 297 ... 447 next »
4462 reviews

Add new review
View Product Index
RSS FEED

Browse reviews

categories | brands | all reviews


DISCLAIMER: Any posts on LJ are posted by individuals acting in their own right and do not necessarily reflect the views of LJ. LJ will not be held liable for the actions of any user.

Latest Projects | Latest Blog Entries | Latest Forum Topics

HomeRefurbers.com