LumberJocks

Reviews: 3M

  • Advertise with us
Finally can breathe safely!

Finally can breathe safely!

04-20-2012 12:27 PM by gillyd | 15 comments »

http://www.amazon.com/gp/product/B000Z53WKU/ref=oh_details_o01_s00_i02 After trying a few masks, this one is definitely the best so far. I rarely give 5 stars, and in fact this is my first 5 star item that I have used. Its comfortable, inexpensive, and has a down firing exhaust that prevents any condensation on safety glasses. The adjustments for the straps are easy and it has the best detachment mechanism so you aren’t wearing out the adjustments. Cost: ~$20 I am using the ...

Read this review »


A good buy.

A good buy.

12-15-2011 12:36 AM by Andy123 | 5 comments »

I bought this today, after I knew I was going to do a lot of sanding. I’ve been using the paper masks for a while and I hate them. I hate how the paper ones make you breath hot air and are really stuffy. I also hate how they never fit right. Opening 3m Respirator was easy and it was easy to assemble. All you have to do is attach the filters. There is two head straps on the respirator. The top one starts off as one strap but splits into two and cradles your head comfortably. The bott...

Read this review »


Meets my needs

Meets my needs

10-27-2011 12:41 AM by Vrtigo1 | 30 comments »

I recently purchased an HVLP system and wanted to buy a respirator to go with it to avoid inhaling the atomized overspray. I went with the 3M 7500 because Marc (The Wood Whisperer) did a segment on his podcast about respirators in which he recommended it. I purchased the bare respirator with no filters, then added a set of the P100 filters. The resiprator is quite lightweight and isn’t a nuisance to have on your face, which I think is important because is your safety gear is a hass...

Read this review »


3M Sandblaster Holder and Pre-cut Sandpaper Sheets

3M Sandblaster Holder and Pre-cut Sandpaper Sheets

06-26-2011 10:51 AM by David Grimes | 3 comments »

I picked this 3M Sandblaster holder and one box each of 80, 120, and 220 grit up a few months ago at one of the big box stores on an impulse because my guys go through the sanding sponge blocks like addicts. But I took it home to give it a try first since I was ripping a lot of 3/8” plywood on the table saw (and then to length on the sliding miter saw). I used this to sand over the cut edges very quickly. It was handy. Not miraculous, of course, but very handy. Comfortable to hol...

Read this review »


Temporary attachment

Temporary attachment

03-23-2011 07:57 PM by Paul | 3 comments »

I think they are much better than the usual doubble stick tapes such as carpet tape that I’ve been using for years. These tabs come in a variety of sizes and are intended for use as refills for many clips, hangers, etc used for wall hanging.When you use them wood to wood, wood to metal, etc just leave the tab exposed and when comes time to remove them pull the tab to release the adhesive, no sticky residue to clean up, no damaged wood surface, no struggles, no hassle. They are ...

Read this review »


3M Respirator

3M Respirator

08-13-2010 04:19 PM by mnorusis | 25 comments »

At the start of the first coat of lacquer I put on in preparing for finishing a desk project, I knew I would be buying a respirator immediately. The smell is aweful and while I’m not certain the safety risks of breathing it, I have read some pretty bad stories online about the fumes. I went to HomeDepot and decided to buy the best mask they had…so this was it. I did 0 research on masks, including for best model/price. This mask certainly does the job I needed it to do. Wh...

Read this review »


Works well thus far

Works well thus far

02-26-2009 11:39 PM by Will Mego | 4 comments »

With the intention of using it to spray glue down pieces of sandpaper for the Scary Sharp sharpening method, I bought this at my local Ace Hardware, large can was about $12 or so. I’ve only used it a couple of times, but thus far it works well, giving me paper glued onto 1/2” plate glass strongly enough to work chisels on it, but it pops off easily when I want to remove the paper. I just spray a tiny amount on the back of the paper, and stick it down, let it set for a few seconds....

Read this review »


3M™ SandBlaster™ Flexible Abrasives

3M™ SandBlaster™ Flexible Abrasives

02-20-2008 10:31 PM by leonmcd | 3 comments »

I just discovered these and used them on my Valentine’s Box 2008 project. Because of the small size of the box and the rounded bottom made by the bowl/tray router bit, I needed something flexible to follow the curves. I also need something that I could agressively work some problem areas left by the router. My regular sandpaper didn’t seem agressive enough and foam backed sanding pads are too stiff on the sanding surface to smoothly follow the tight curves. These pads are mu...

Read this review »


« prev 1 2
18 reviews

Add new review
View Product Index
RSS FEED

Browse reviews

categories | brands | all reviews


DISCLAIMER: Any posts on LJ are posted by individuals acting in their own right and do not necessarily reflect the views of LJ. LJ will not be held liable for the actions of any user.

Latest Projects | Latest Blog Entries | Latest Forum Topics

HomeRefurbers.com