LumberJocks

Reviews: Ryobi

  • Advertise with us
Good saw, with modifications!

Good saw, with modifications!

04-25-2010 06:06 AM by msdameng | 6 comments »

Straight out of the box you will be dissapointed with this saw. Some of the major flaws are very pronounced vibration above the 1200 spm speed, the blower is not nearly strong enough, the knob to tighten the tilt on the tabletop is made of of soft rubber and will bust if overtightened, also if you plan on using the holddown foot it is almost impossible to get it tight enough to not twist if the piece of wood you’re cutting actually tries to pull up against it. However, I have found th...

Read this review »


Easy to use and does what it's supposed to do.

Easy to use and does what it's supposed to do.

05-20-2013 08:24 PM by Bill1974 | 5 comments »

I have had this biscuit joiner the (JM82) for a few months and it has worked well. It’s easy to adjust and handle. It seem a little more powerful than a porta cable one that I had used, it get up to full speed quicker than the PC. The case is nice, but the bag location is a little awkward. It would also be nice if there were a better way to store extra biscuits in it. Additionally the cord gets bent pretty tight when put in the case, just past the strain relief on the unit, I cu...

Read this review »


A good starter miter saw or second miter saw for fast work

A good starter miter saw or second miter saw for fast work

12-18-2008 12:31 AM by ferstler | 5 comments »

I am not sure if this saw is still available with the exact specifications and model number of this one, but they do have one in the same price class: $99.00 and it probably works just as well. As with all models in this size class, the saw can cut a 2×6 at 90 degrees and a 2×4 at 45. The miter-lock handle in right in front and the bevel release is in the back. It can bevel in one direction out to 45 degrees and the motor is a decently powerful 14-amp job. It comes with a decent ...

Read this review »


Good concept but made from poor materials

Good concept but made from poor materials

05-23-2009 03:48 AM by TNBodger | 5 comments »

I wouldn’t mind having a 6” x 48” belt sander, but like many weekend woodworkers, I don’t have the floor space for one. I have always managed fairly well with the smaller benchtop 4” x 36” machines so when it came time to buy a new one I looked at everything I could find out there and settled on the Ryobi BD4600 sold at Home Depot. I liked the easy way belts are changed by the flip of a lever. Aligning the belt is done by a quick turn of the thumb wheel. Bu...

Read this review »


Great miter saw stand, if you can't have yours set up all the time.

Great miter saw stand, if you can't have yours set up all the time.

08-09-2009 07:59 AM by Trikzter | 5 comments »

I bought this Ryobi Miter Saw stand a few months ago and I love it. The picture shows it set up, but the legs will fold in and you can carry it around or for storage. I don’t have enough room to have a saw set up all the time and I have to set my saw up outside to cut for now. For the first time use, you have to attach the cross “sleds” or feet if you will, then attach the saw and the feet to the cross bars. It’s best to tilt the front towards you and then let the wei...

Read this review »


Ryobi AP1301

Ryobi AP1301

01-28-2011 09:28 AM by HobieMan | 5 comments »

I love my planer, again for the price. Mine does have the 4” dust port so it must be a later version. I recently noticed that it is not planing a consistent thickness across the width of the board and I am getting inconsistent snipe, some times worse than others on the same board. It is going off to a service center tomorrow.

Read this review »


THREE (3) packs of Ryobi 5 in. Plain-End Scroll Saw Blades Assortment

THREE (3) packs of Ryobi 5 in. Plain-End Scroll Saw Blades Assortment

03-02-2013 05:54 AM by mikethetermite | 3 comments »

This was the first time I tried some of these they worked quite well. Got them all for for $.99. 108 for $.99, not a bad deal at all. http://www.ebay.com/itm/Ryobi-5-in-Plain-End-Scroll-Saw-Blades-Assortment-/290867787346?pt=LH_DefaultDomain_0&hash=item43b9123652 This E-Bay auction was for THREE (3) packs of Ryobi 5 in. Plain-End Scroll Saw Blades Assortment (each is 36-Pack) Model # A28SC12. 12 blades each with 11.5, 12.5 and 41 teeth per inch.

Read this review »


Plenty of power, good chuck, a little noisy.

Plenty of power, good chuck, a little noisy.

07-22-2009 04:17 PM by dbhost | 2 comments »

It’s been nearly two years since I purchased my Ryobi D46CK driver drill to replace an old Craftsman drill that had been on long term loan a little too long… The features I liked about this particular drill were the fact that it had a keyless chuck, with a good, predictable chuck. The blow molded case helps with storage and at least TRYING to keep my shop tidy. Power from this drill has been great, after Hurricane Ike I used it with a 1.5” long shaft (18”) spade ...

Read this review »


Nice scroll saw that has some useful features

Nice scroll saw that has some useful features

12-16-2008 12:26 AM by ferstler | 1 comment »

I do not use this saw much, but I got it on clearance at Home Depot some time ago, and do manage to make the purchase worth the cost from time to time. Yep, it no longer is available there as a new item, but Sears still has the same unit available in its stores (in a different color, of course), and used items might be on hand here and there. Other than more vibration than I like, this saw works OK. I found that by mounting the thing to a heavy bench (which itself is bolted to the shop wa...

Read this review »


 Ryobi 7 1/2 inch CMS

Ryobi 7 1/2 inch CMS

08-03-2011 03:19 AM by tomd | 1 comment »

When I first saw this saw I though how cute, so little. But I knew it was just up my alley. This is not for home repairs or major construction, but is brilliant at cutting small parts. Hook it up to a frued 7 1/2 60tooth blade and you get great smooth cut small parts. I use it for segment turning in cutting the small angles and I also use it in making bandings and fan motifs. If your cutting small parts this is a great saw.

Read this review »


« prev 1 2 3 4 5 next »
44 reviews

Add new review
View Product Index
RSS FEED

Browse reviews

categories | brands | all reviews


DISCLAIMER: Any posts on LJ are posted by individuals acting in their own right and do not necessarily reflect the views of LJ. LJ will not be held liable for the actions of any user.

Latest Projects | Latest Blog Entries | Latest Forum Topics

HomeRefurbers.com

Latest Projects | Latest Blog Entries | Latest Forum Topics

GardenTenders.com :: gardening showcase