LumberJocks

Reviews: Grizzly

  • Advertise with us
A good value.....

A good value.....

03-07-2015 01:56 AM by Adrock1 | 10 comments »

I think I’m the first to review this saw so I’ll be as thorough as possible. Please forgive any sloppy typing. My computer is dead so I’m on my phone. Anyway I was in the market for a 120 volt saw and had it narrowed down to this grizzly or the new delta 36-725. I ended up with the grizzly. 1. Customer service I ordered over the phone as I had some questions about shipment. The lady that took my call was a pleasure to deal with and knew her stuff. The order process ...

Read this review »


5th day with the New G0733

5th day with the New G0733

02-19-2015 12:18 PM by CyF | 5 comments »

I had said in my Blog about the trip to Grizzly that I would post a review after using the new lathe for a bit. Well I have wasted no time. I have already been on it about 15 hours in five days. But a little history first. I have owned and used 7 lathes over the past 25 years. They have all been Step pulley or Reeves drive machines, until I modified the one I was using before I got the new lathe, It I had modified with a treadmill motor and controller, but tread mill motors are NOISY. S...

Read this review »


My tenon making solution

My tenon making solution

10-09-2014 01:33 AM by CharlesA | 4 comments »

I’ve made tenons using several different methods. I had avoided buying a tenoning jig because it seemed like an unnecessary outlay of funds. I could make them by hand, with the bandsaw, or using a dado blade on the table saw. But for whatever reasons, I always have been a little frustrated by how they came out. I ended up doing way too much fine tuning with chisel/plane/sandpaper. So, I bit the bullet and purchased the Grizzly tenoning jig through Amazon, $88.59. I was annoyed...

Read this review »


Great performer. Zero problems. 5 stars.

Great performer. Zero problems. 5 stars.

10-05-2014 03:40 PM by JSB | 14 comments »

I bought the Grizzly G0690 about 6 months ago and feel like that’s enough usage to talk about my thoughts. It’s a damn good saw. I don’t have any major complaints after using it for this long. Just a couple nit-picky things that I don’t think justify bringing this down from 5 stars. After comparing prices on similar spec saws I would definitely buy this saw again if I had to do it all over. Pros:strong motorgreat fencelarge cast surfacebest value compared to other b...

Read this review »


Horizontal Boring Machine

Horizontal Boring Machine

08-25-2014 10:44 PM by rad457 | 2 comments »

Assembled my G0540 Single Spindle Horizontal Boring Machine and thought I would post some of my observations and opinions. Machine was packed well and pretty easy to remove from crate, assembly was very easy and instruction were there and quite clear if needed! The washers were the wrong size not a big problem.I found that for my purposes the table should raise higher so will have elevate it in the future when I find the time.The X -Y feature works very well with the exception that the table...

Read this review »


Grizzly G0452Z 6” Jointer with Spiral Cutterhead

Grizzly G0452Z 6” Jointer with Spiral Cutterhead

07-22-2014 01:45 AM by JerryinCreek | 13 comments »

This is a summary of my experience in purchasing, assembling and using this machine. I began by attempting to place my order on-line, but the choice of lift gate service was not available on the web site. I then called Grizzly and the gentleman who assisted me was going to show me where I missed it. However, I apparently did not miss it, it was not on the web site for this product. The order taker was quite courteous and completed my purchase. I ordered this unit on a Wednesday and was ...

Read this review »


Grizzly G0582 24: Wide Belt Sander

Grizzly G0582 24: Wide Belt Sander

07-03-2014 02:10 PM by BoardSMITH | 7 comments »

After two months of hard use I feel somewhat qualified to write a decent review. So here goes. Crating and packing – Blah, blah, blah, etc… Delivery – Blah, blah, blah, etc… Instruction manual – Blah, blah, blah, etc… Fit and finish, Blah, blah, blah, etc… Now that all the fluff is out of the way. I purchased a Grizzly wide belt sander because I was unable to find another on the market of that size. My budget would handle a 24̶...

Read this review »


Never again will I trust Grizzly for "Precision" equipment

Never again will I trust Grizzly for "Precision" equipment

06-08-2014 08:09 PM by Hawkeye1434 | 33 comments »

I just had the biggest hassle of my life when I got the grizzly 8 inch spiral head dovetail jointer. It took me about three months before I actually got a chance to unpackaged my purchase and then it took me another three days to get all the Schmutz cleaned off of it from the being sent from overseas. I thought to myself boy this is going to be awesome 8 inch helical cutterhead for less than half of the price of a powermatic. Once I finally got the machine set up I put a straight edge on i...

Read this review »


First impressions of the Anniversary Edition G0555 14" Band Saw

First impressions of the Anniversary Edition G0555 14" Band Saw

06-03-2014 10:53 PM by dansnow | 17 comments »

After nursing along my Dads old Craftsman 12” band saw, I was really looking forward to getting my new saw. After much research and pricing I had settled on the G0555LANV 14” for a number of reasons. It had a 1 HP motor where several others in the price range were 3/4HP. It had a cast iron frame and table instead of cast aluminum and stamped steel. The wheels were cast iron instead of cast aluminum and it had two speeds. But one of it’s biggest selling features to me was the...

Read this review »


Something this heavy should work!

Something this heavy should work!

05-25-2014 06:17 PM by shu | 22 comments »

This is a poorly designed sander.You would think that if a tool weighed as much as a submarine, it would be steady worker, but the Grizzly GO458 takes a break about every 30 minutes and decides to adjust itself where it wants to be.Seriously, it has many design problems.The feed belt will only stay in adjustment while you are watching it. It must be a quantum physics thing. After about a half hour of sanding, when your hands and mind are fixed on keeping it from sniping your work, because the...

Read this review »


1 2 3 4 ... 21 next »
206 reviews

Add new review
View Product Index
RSS FEED

Browse reviews

categories | brands | all reviews


DISCLAIMER: Any posts on LJ are posted by individuals acting in their own right and do not necessarily reflect the views of LJ. LJ will not be held liable for the actions of any user.

Latest Projects | Latest Blog Entries | Latest Forum Topics

HomeRefurbers.com