LumberJocks

Reviews: Lee Valley

  • Advertise with us
Great Product!

Great Product!

03-05-2010 04:10 PM by Newfounlandwood | 5 comments »

Hey guys, I recently received a shipment of tools from Lee Valley and I’ll be putting in a small review on all of them. A straight edge is something that I have never owned before. It’s not something that is easy to find in Newfoundland, Canada (along with any other woodworking tools). But with the purchase of a router table and the making of a mitre saw stand, my twenty dollar HD level was not going to cut it. I am very pleased with this product. The length of the body is conc...

Read this review »


Self Cleaning Blast Gates

Self Cleaning Blast Gates

02-16-2010 10:00 PM by Greg..the Cajun Wood Artist | 8 comments »

I have tried numerous blast gates, metal and plastic. These from Lee Valley are the best I have found and they never clog because of the way the gate pushes any possible clog out when the gate is open and closed. I have been using them for 2 years without a clog. They do not come with the knobs…I added them for ease of use. when remodeling my kitchen last september I saved all the knobs from my old cabinets with the intention of re-using them on the new cabinets. I was outvoted by my w...

Read this review »


Not sure what to think of these, but felt misled by Lee Valley

Not sure what to think of these, but felt misled by Lee Valley

01-20-2010 04:07 AM by funchuck | 14 comments »

I have mostly seen high praise of Lee Valley, but I bought these 2 items and felt that their website was misleading. The 2 pictures above are from their website. They are: 1. Pocket Folding Squares – they have a 45 deg, 90 deg and 135 deg setting. They are supposed to be accurate to within 0.06 deg. I bought the 6” version. 2. Engineer’s Squares – they are machined to 0.001” deviation per inch. I bought the 2” and 4” versions. If you l...

Read this review »


A new way to find and track all those thread sizes in the tool shop

A new way to find and track all those thread sizes in the tool shop

01-16-2010 02:33 AM by Bob #2 | 14 comments »

Seems I am always lookng for a nut or bolt for a peice of geat in my shop.Without taking a spare with me to the nut shop I am usually stubbed out with a replacement that’s eighr too big or too small.Now all I have this to fill in the blanks for size and thread. I’ll quaote from the excellent writeup rather than try to polish a pear.“a plate tapped for 10 National Coarse sizes (1-64 to 1/4-20), 10 National Fine sizes (1-72 to 1/4-28) and 8 Metric Coarse sizes from M1.6 to ...

Read this review »


Lee Valley's Variable Round Over Bit

Lee Valley's Variable Round Over Bit

11-20-2009 07:37 PM by handi | 0 comments »

I got to try out Lee Valley’s new Variable Roundover bit. This bit has two parts that can be spaced apart with the included shims to round over the top and bottom of stock from .79” to 1” thick. It does take a bit of checking to assure that the bit is set to the proper width. Since the cutting tips are offset, it is difficult to exactly measure the setting. Make some extra stock and do test cuts. This bit was designed to make tool handles using templates and Lee Valley...

Read this review »


Paul Beebe #11 Carving Knife for Lee Valley

Paul Beebe #11 Carving Knife for Lee Valley

11-07-2009 06:16 AM by just_adam | 5 comments »

Hello and this review carries my initial impressions of a fine carving knife made by Paul Beebe for Lee Valley Tools in Canada. At the time, it cost me about $33USD and presently it is in there on line catalog at this address: http://www.leevalley.com/wood/page.aspx?c=2&p=31085&cat=1,130,43332,44073&ap=1 I’ve used all sorts of knives in my meandering about the wood. Opinels, Ken Onions, single edge razors, XActos…James Krenov wrote a great passage about using k...

Read this review »


Great for something, but not for spreading glue!

Great for something, but not for spreading glue!

09-28-2009 01:42 AM by thiel | 14 comments »

I hate the idea of tossing out acid brushes after a few uses (they’re steel!) and I’ve been looking for alternatives (for the record, there aren’t any :-) so I bought these little dealios. Long story short, they are TERRIBLE for spreading glue. They act more like a squeegee—pulling glue away from your intended target. Which brings us to what they ARE good for, and that’s scraping glue off once its skinned over. These things are a nice plastic, they are g...

Read this review »


Lee Valley 16J09.90 Double-Bearing Flush Trimming/Template Bits

Lee Valley 16J09.90 Double-Bearing Flush Trimming/Template Bits

07-29-2009 03:19 AM by Brian | 0 comments »

Tried this bit out on a round tabouret top and shelf and this bit does a great job. No tearout whatsoever because you’re never going against the grain..The attached link explains it pretty well.Definitely recommended.

Read this review »


Lee Valley Brad Point Bits - Set of Seven

Lee Valley Brad Point Bits - Set of Seven

11-02-2008 07:03 PM by ChicoWoodnut | 7 comments »

I was in need of some brad point bits to drill holes for a set of ball catches I am installing. I have been using regular twist bits and needed something with a centering guide. My set of Irwin Jennings-pattern auger bits don’t go to 1/4”. I looked at brad point bits at the Borg and didn’t like any of the ones I saw. The lip was simply a point ground into the edge of the radial cutter. It didn’t look like it would leave a clean hole on entry and that is what I am ...

Read this review »


Specialized plane that has a lot of uses

Specialized plane that has a lot of uses

05-31-2008 07:49 AM by ShannonRogers | 6 comments »

I got a great deal on the set of these on ebay, but after using them on my new countertop and router table to trim edge banding I would definately pay full price in a heartbeat. These use the same thick iron and easy adjustment as all the other bevel up planes in the Veritas line. I followed the set up instructions included and was making shavings in just a few moments. After using the set screws to dial in the fit, I pulled out the iron and honed it up to 8000. The back of the iron was a...

Read this review »


« prev 1 2 3 4 next »
33 reviews

Add new review
View Product Index
RSS FEED

Browse reviews

categories | brands | all reviews


DISCLAIMER: Any posts on LJ are posted by individuals acting in their own right and do not necessarily reflect the views of LJ. LJ will not be held liable for the actions of any user.

Latest Projects | Latest Blog Entries | Latest Forum Topics

HomeRefurbers.com

Latest Projects | Latest Blog Entries | Latest Forum Topics

GardenTenders.com :: gardening showcase