LumberJocks

Reviews: Lee Valley

  • Advertise with us
Lee Valley Square Hole Punches

Lee Valley Square Hole Punches

11-11-2011 07:27 AM by vipond33 | 23 comments »

This is a review of the Veritas Square Hole Punch, available individually or as a set of six, ranging in size from 3/16” to 1/2” by sixteenths. These punches are most often used for period work such as Greene and Greene style pieces where a raised plug is inserted, or for decorative pierced work (like the ones in my pictures) or for small square mortices. You could also use them as the beginning of much deeper mortises, using the perfect opening created as your guide for furth...

Read this review »


Lee Valley Brad Point Bits - Set of Seven

Lee Valley Brad Point Bits - Set of Seven

11-02-2008 07:03 PM by ChicoWoodnut | 7 comments »

I was in need of some brad point bits to drill holes for a set of ball catches I am installing. I have been using regular twist bits and needed something with a centering guide. My set of Irwin Jennings-pattern auger bits don’t go to 1/4”. I looked at brad point bits at the Borg and didn’t like any of the ones I saw. The lip was simply a point ground into the edge of the radial cutter. It didn’t look like it would leave a clean hole on entry and that is what I am ...

Read this review »


Self Cleaning Blast Gates

Self Cleaning Blast Gates

02-16-2010 10:00 PM by Greg..the Cajun Box Sculptor | 8 comments »

I have tried numerous blast gates, metal and plastic. These from Lee Valley are the best I have found and they never clog because of the way the gate pushes any possible clog out when the gate is open and closed. I have been using them for 2 years without a clog. They do not come with the knobs…I added them for ease of use. when remodeling my kitchen last september I saved all the knobs from my old cabinets with the intention of re-using them on the new cabinets. I was outvoted by my w...

Read this review »


Lee Valley Bevel Edge Chisels

Lee Valley Bevel Edge Chisels

02-04-2008 01:49 AM by dustynewt | 4 comments »

At $76.00, these chisels are a great buy for all around shop use. I have had them a year now and have re-honed them only once. They really hold an edge. The set goes from 1/4” – 1 1/2”. The oblong handles are comfortable, don’t roll around and can take a real beating. They are better than the Marples and the other big box brands that I have used.

Read this review »


Lee Valley Dripless Glue Bottle

Lee Valley Dripless Glue Bottle

01-28-2012 01:56 PM by Sheila Landry (scrollgirl) | 32 comments »

Not too long ago, I did a blog which asked people what type of glue they liked best for different woodworking projects. Many people stated that they used white or tan wood glue for many of their gluing applications. I often use this type of glue too, not only for my scroll saw projects, but also for building smaller projects such as boxes and things of that nature. One problem that I had was application. Since I used the glue on smaller projects and only in small amounts, I found that t...

Read this review »


Paul Beebe #11 Carving Knife for Lee Valley

Paul Beebe #11 Carving Knife for Lee Valley

11-07-2009 06:16 AM by just_adam | 5 comments »

Hello and this review carries my initial impressions of a fine carving knife made by Paul Beebe for Lee Valley Tools in Canada. At the time, it cost me about $33USD and presently it is in there on line catalog at this address: http://www.leevalley.com/wood/page.aspx?c=2&p=31085&cat=1,130,43332,44073&ap=1 I’ve used all sorts of knives in my meandering about the wood. Opinels, Ken Onions, single edge razors, XActos…James Krenov wrote a great passage about using k...

Read this review »


Great new router bit for your collection

Great new router bit for your collection

03-01-2012 02:46 AM by T. D. Reid | 18 comments »

This is a great bit that I am using to make Arts and Craft style legs with so that they show quarter sawn white oak on all four sides. The instructions also say that you can use it to build boxes or make drawers but I have not attempted these procedures. The bit comes in two sizes one for use on stock 1/2 -3/4 of an inch and the one I purchased for use on 3/8 – 1/2 inch stock. Now during the set up I did not realize that the bit that I had purchased was meant for use on the thinner stoc...

Read this review »


1/4" drill bit extenders that work

1/4" drill bit extenders that work

05-09-2010 05:21 AM by Bob #2 | 8 comments »

Over the years I’ve probably purchased a half dozen different quarter-inch bit extensions all of which have failed for one reason or another. Either thay were too long or too short or too wobbly or just plain junk and end up frustrating me every time I attempted to use them. This morning I went out to check a couple of vendors that supply these devices to see if there were any improvements. The first store I checked had a set five but they were sealed in plastic and the sales clerk ...

Read this review »


Lee Valley Bench Plane Blade and Chip Breaker Set - Stanley/Record

Lee Valley Bench Plane Blade and Chip Breaker Set - Stanley/Record

04-06-2013 10:34 PM by knothead | 8 comments »

Well, Lee Valley has done it again….. After trying for years to get my #4 Smoother working as well as it should, (Always getting close but not quite there) I finally gave up and ordered this Plane Blade and Chip Breaker Set to replace an original cutter and chip breaker in my Stanley #4 smoother. I have previously purchased a Hock replacement blade for my #5 and liked it but they are a little spendy so I set out to see what was available, The Pinnacle blades looked good but seem a l...

Read this review »


Honing Guide

Honing Guide

03-31-2011 01:49 PM by dbray45 | 10 comments »

Bought this and was very surprised. My other honing guide clamps on the sides and edges for the larger blades and has a triangle to hold the smaller chisels and blades. This honing guide clamps on the flat side of the blade and holds it. The guide I give 5 stars. The guide comes with a piece of stick on rubber which I put on the anvil of the guide so that the blade does not move around. The anvil, as I call it, has scribed lines to show if your blade is square to the guide, the rubber ...

Read this review »


1 2 3 4 next »
32 reviews

Add new review
View Product Index
RSS FEED

Browse reviews

categories | brands | all reviews


DISCLAIMER: Any posts on LJ are posted by individuals acting in their own right and do not necessarily reflect the views of LJ. LJ will not be held liable for the actions of any user.

Latest Projects | Latest Blog Entries | Latest Forum Topics

HomeRefurbers.com

Latest Projects | Latest Blog Entries | Latest Forum Topics

GardenTenders.com :: gardening showcase