LumberJocks

Reviews: Woodcraft

  • Advertise with us
Woodsmith Aluminum Box Joint Jig

Woodsmith Aluminum Box Joint Jig

1817 days ago by CharlieD | 9 comments »

I was fairly pleased with this product and give it a 3.5 rating. . It was somewhat difficult to use and with some minor changes could be greatly improved. The DVD instructions were pretty good once you watched it several times. I found it difficult to hold the boards in place when you have a lot of cuts to make. Some type of hold down fasterner would help but also would slow the process quite a bit. What you don’t realize when you buy the jig is that you might as well and go ahea...

Read this review »


Heavy Duty wheel casters

Heavy Duty wheel casters

1920 days ago by Don K. | 8 comments »

Like many, I make mobile base’s for all of my shop equipment. I have used plastic, rubber metal etc. And while they serve their purpose, they have many short falls. The plastic and metal ones hang up on every chip of wood and piece of trash on your floor, and have terrible locking systems. The rubber ones while they do roll much easier across the floor, still have the same lousy locking system, and develop flat spots when they sit for a extended time. Recently while I was at my ...

Read this review »


Nice Tenoning jig, but....

Nice Tenoning jig, but....

1734 days ago by drfixit | 11 comments »

I had to modify it, by drilling new holes for the miter bar to use it on my Ridgid TS3612 saw. It has 2 sets of holes in it, but one set put it on top of my blade and the other set put it too far away. It was very easy to assemble other than this but after assembling it and adjusting it. It has 3 adjustable screws to fit your miter slot. It can be used for any angled tenon from 0 to 45 degrees. Wish I had bought one sooner.

Read this review »


Woodcraft Dust Collector Remote Control

Woodcraft Dust Collector Remote Control

1109 days ago by newTim | 14 comments »

I’ve seen these things in the local Woodcraft for many months and finally bought one when it recently went on sale. Many folks have been ‘hotrod-ding’ their dust collectors, especially the Harbor Freight. I’m happy to report this is working great. Just plug it in to the wall and plug the collector in to it. The HF is supposed to be a 2HP motor, but it is still 110V, so I was reluctant to buy this thinking it would be overpowered. Not true. I wish I had bought thi...

Read this review »


Cabinet scraper

Cabinet scraper

1374 days ago by ducky911 | 13 comments »

Hi, I thought I would post this as there may be some others that have not tried using scrapers. Oh man if I only hand the hours back spent on sanding. My wife been bugging me for a bedroom mirror and since I been buying tools lately I figured that her project better move up on the list. I had some hard maple left over. I ran the frame material through the table saw on an angle to make a cove—-I had done that several times before and it takes alot of sanding and making special b...

Read this review »


Do not have high expectations!

Do not have high expectations!

1003 days ago by slickSqueegie | 38 comments »

I bought it, I guess it works but I am not happy with it. I still would rather “freehand” my blades! What do I expect for 13 bucks? Call me picky if ya want. When sharpening, I expect nothing less than perfection! And this little unit is far from it!

Read this review »


new clamp purchase

new clamp purchase

1498 days ago by woodsmithshop | 15 comments »

I just purchased six of the Woodcraft clamping system clamps, they were on sale, plus if you bought $100 or more the shipping was free, I have been having trouble keeping any panels flat on glue ups, this system does a great job, though not totally perfect, you can get near and sometimes perfect if you are careful, and your 2×2 are made very square. you must plan ahead carefully when doing a glue up, otherwise it can be awkward trying to get your boards aligned, it is best to not add th...

Read this review »


Works well after you work out the kinks

Works well after you work out the kinks

1909 days ago by cmaeda | 4 comments »

I got this so I can make my own vises. I also bought some 1 1/4” dowels to go along with it. This does require some practice to use. The instructions are very sparse and the construction was kind of cheap. The guide that is screwed onto the threader was installed incorrectly so it was difficult to remove. The threader had some scratches and small gouges on it. The tap was fine.I tried it right out of the box. I followed the instruction, soaked the dowel in some BLO and then start...

Read this review »


Review of the Woodcraft Anti Kickback Safety Rollers

Review of the Woodcraft Anti Kickback Safety Rollers

166 days ago by steve_in_ohio | 16 comments »

I bought these rollers a couple of days ago because my table saw is old and it doesn’t have a riving knife and I don’t like to use the blade guard. Also I had problems when running long boards thru the table saw that they would try to move away from the fence, so I bought these rollers. I mounted these on my fence with a t-track instead of the rail that it is sold for these. After some simple assembly I started using these and I love them. They hold the wood down to the table and ...

Read this review »


Great for uneven floors

Great for uneven floors

1748 days ago by DannyBoy | 8 comments »

From the start, I needed to make sure that my saw would be movable. With a small shop, floor space is at a premium and it only makes things difficult to admit that my floor is not at all level and even. This system took care of both of those needs. The casters are well built and work well on the uneven floor. Plus, once you are done moving the unit, you flip it down onto it’s own feet right into your floors sweet-spot. Two bits of advice: First, you probably won’t matc...

Read this review »


1 2 3 next »
25 reviews

Add new review
View Product Index
RSS FEED

Browse reviews

categories | brands | all reviews


DISCLAIMER: Any posts on LJ are posted by individuals acting in their own right and do not necessarily reflect the views of LJ. LJ will not be held liable for the actions of any user.

Latest Projects | Latest Blog Entries | Latest Forum Topics

HomeRefurbers.com

Latest Projects | Latest Blog Entries | Latest Forum Topics

GardenTenders.com :: gardening showcase