LumberJocks

Reviews: JET

  • Advertise with us
Initial Impressions of this drill press

Initial Impressions of this drill press

04-25-2010 08:41 PM by AjayO | 6 comments »

I wanted to share my initial impression of this new Jet drill press. This is a new 12” portable drill press offering from Jet with digital speed readout (hence DRO: Digital Read Out in the name), variable speed and laser cross hair alignment. I picked it up as a barely used from a local person about 1.5 months ago. I haven’t used it a lot but have been looking for a drill press for quite some time so at least wanted to share some initial impression. I compared this press to Del...

Read this review »


JET 6-inch riser kit for 14 inch bandsaw

JET 6-inch riser kit for 14 inch bandsaw

07-07-2010 02:34 AM by MOJOE | 15 comments »

So I installed this kit today on my JWBS-14DX. It was very straightforward and took about 30 minutes by myself. I must confess that I watched a quick vid on youtube, and ditched the instructions. I did look through them afterwards that they seemed alright. Anyway, the fit and finish on this kit is pretty good, and everything went together smoothly. My only complaint…..the powder coating on the riser block was not quite as nice as the powder coating on the saw, but, that really isn&...

Read this review »


Jet 708480K JPS-30 Quality Hybrid Saw for under $800

Jet 708480K JPS-30 Quality Hybrid Saw for under $800

07-30-2010 08:04 PM by Holz_und_Geschichte41 | 6 comments »

Jet 708480K JPS-30: 10-Inch ProShop Table saw 1-3/4-Horsepower 30-Inch Rip fence With Steel Wings I have been woodworking for about 2 years now and felt it was time to spend the necessary dough to improve accuracy, cuts, rips, and broaden techniques. I spent a lot of time researching table saws based off cost, features, etc. I decided on this Jet for a handful of reasons: •Cost: $799.00 through Amazon: Amazon allows you to finance certain large ticket items for 12 months same as cash....

Read this review »


JET JJP-12HH, 2-month review

JET JJP-12HH, 2-month review

01-21-2011 11:33 PM by mstenner | 17 comments »

After two months with the JJP-12HH, I’m ready to share what I’ve learned. The bottom line: this is a great tool and I’d recommend it for the serious amateur. I wanted a lot of capability in my small (12×15) shop and am very happy. Shipping & Unpacking This is a large and heavy tool (my wife says I’m no longer the “biggest tool in the shop”), and it comes almost fully assembled. You will need to get the crate where it’s going intact. ...

Read this review »


Used Jet JJ-6CS jointer, seems to be a bargain

Used Jet JJ-6CS jointer, seems to be a bargain

02-22-2011 05:17 AM by ic3ss | 10 comments »

I picked this up from a Craigslist ad recently for $200. SCORE!! I wanted the CSX with 1 hp motor, but this one will do. And with this being about half the going price for a newer CSX, I can put that money towards some chisels or a shoulder plane. Looks like it’s seen some action, I had to clean a bunch of surface rust from the fence and tables. A thorough cleaning did wonders, and now I need to pull the knives and get them sharpened. Everything seems to work fine, even the bearings are...

Read this review »


Jet Speed Clamps with Slip Clutch and 4" Throat

Jet Speed Clamps with Slip Clutch and 4" Throat

09-12-2011 08:34 PM by pintodeluxe | 1 comment »

These clamps were needed to reach over my pipe clamps during complicated glueups. The long 4” throat can accomplish this easily. The handle is large enough in diameter for good clamping pressure, and they easily closed all of my mortise and tenon joints with no gap. Cons: The clamp pads fall off easily. This is easily solved with a dab of silicone caulking. The slip clutch occasionally slips when you don’t want it to. I usually prefer clamps with a trigger for ju...

Read this review »


I am disappointed

I am disappointed

10-20-2011 10:30 AM by MNgary | 17 comments »

While not, in my opinion, a professional level lathe this full-sized lathe is adequate for advanced hobbyists wanting to turn spindles longer than popular midi lathes allow and it does a nice job turning turning shallow bowls. I have not turned pens so do not know how it performs for that more precision task. Assembly is straightforward and waiting until the 170 pound lathe is placed in its final location before tightening the stand’s bolts allows installation on an uneven concrete ...

Read this review »


As the price falls, the rating rises

As the price falls, the rating rises

12-03-2012 03:33 AM by ic3ss | 10 comments »

I found this Jet JWL 1236 lathe on Craigslist and just got it home and set up today. I’ve gone over many reviews of this lathe on the web, and the couple hours use I’ve had today have proven some of the gripes right. I put a 4×4 on it and rounded it, and I found it has a rattle coming from somewhere but the lathe doesn’t shake like some have said. It seems to have enough weight to keep from dancing around. The rattle I think is made worse by the dull tools I was using, ...

Read this review »


Jet Tools / ToolSelect.com review

Jet Tools / ToolSelect.com review

11-05-2011 03:00 PM by Kjuly | 6 comments »

This is a three part review.The first part is my experiences making the tool review video followed by two videos produced by ToolSelect.comKeith ToolSelect.com review… part 1Who or what is ToolSelect.com? Here is a quote from ToolSelect.com’s website: “ToolSelect.com is an unbiased power tool comparison website that offers our users a wide range of resources and information to assist you in researching your intended purchase.” I am a woodworker who was asked by ToolSelect.com to ...

Read this review »


4 years later for this workhorse

4 years later for this workhorse

06-26-2016 10:51 PM by Cato | 3 comments »

First reviewed this saw a few months after getting it in March 2012. 4 years later and I am as happy today as when I first got the saw. This saw runs smooth, is powerful, and is easy to maintain. The fence is true and stays accurate without needing adjustment, ever. Modular blade guard that it shares with Powermatic is great. Table top has been terrific and when I had to store the saw when we moved just a coat of WD specialist sprayed on it protected it from humidity and moisture ...

Read this review »


« prev 1 ... 5 6 7 8 9 next »
89 reviews

Add new review
View Product Index
RSS FEED

Browse reviews

categories | brands | all reviews


DISCLAIMER: Any posts on LJ are posted by individuals acting in their own right and do not necessarily reflect the views of LJ. LJ will not be held liable for the actions of any user.

Latest Projects | Latest Blog Entries | Latest Forum Topics

HomeRefurbers.com