LumberJocks

All Replies on 1st experience with Jerry's Tail Stock Steady Rest

  • Advertise with us
View Jack Lewis's profile

1st experience with Jerry's Tail Stock Steady Rest

by Jack Lewis
posted 09-13-2017 11:19 PM


5 replies so far

View TheDane's profile

TheDane

5521 posts in 3804 days


#1 posted 09-14-2017 02:13 PM

Sounds like a ringing endorsement to me!

Hope Jerry sells a million of them.

-- Gerry -- "I don't plan to ever really grow up ... I'm just going to learn how to act in public!"

View Nubsnstubs's profile

Nubsnstubs

1403 posts in 1871 days


#2 posted 09-14-2017 03:15 PM

Thanks, Jack. I needed that. Making a hopefully much better video to address your issue of centering the piece for taking out the tenon. It will consist of several holding apparatus’s, some which are so simple you wouldn’t even think of trying it…..

I noticed you were using the extensions. If you were to keep your dimple, you could use your live center to take the tenon down to the nub, then use the TSS on the outboard wheel position. It’s where the wheel struts flare out rather than point inward.

Thanks, Gerry. Wouldn’t that be nice? It will sell a million, but well after I’m gone…..... In the future, it will be as common as a chuck is today. I don’t think turners will have multiples like some have chucks, but most will have at least one, ‘cept Brad. He’s a hardliner, and it will be tough to convince him that he needs one. LOL… .......... Jerry (in Tucson)

-- Jerry (in Tucson) www.woodturnerstools.com

View Jack Lewis's profile

Jack Lewis

326 posts in 1220 days


#3 posted 09-14-2017 04:39 PM



Thanks, Jack. I needed that. Making a hopefully much better video to address your issue of centering the piece for taking out the tenon. It will consist of several holding apparatus s, some which are so simple you wouldn t even think of trying it…..

I noticed you were using the extensions. If you were to keep your dimple, you could use your live center to take the tenon down to the nub, then use the TSS on the outboard wheel position. It s where the wheel struts flare out rather than point inward.

Thanks, Gerry. Wouldn t that be nice? It will sell a million, but well after I m gone…..... In the future, it will be as common as a chuck is today. I don t think turners will have multiples like some have chucks, but most will have at least one, cept Brad. He s a hardliner, and it will be tough to convince him that he needs one. LOL… .......... Jerry (in Tucson)

- Nubsnstubs

Jerry; As I muse the use of this chuck, I reasoned if one were to “not” dimple the blank with one of the outer pins, the resulting pattern would show exactly the configuration of blank on the chuck as long as the chuck is mounted exactly the same each time on the scroll chuck. I am going to drill a small pin hole in the chuck and locate it between the # 1 and #4 jaws of the scroll chuck. Or I could dedicate a scroll chuck to the task and leave it permanently mounted.

-- "PLUMBER'S BUTT! Get over it, everybody has one"

View Nubsnstubs's profile

Nubsnstubs

1403 posts in 1871 days


#4 posted 09-15-2017 03:21 AM

Jack, there should be a mark on the EDGE of the Chuck Plate. It should look like a V, over the screw that is directly over the letter A in the word Plate. I have designated that as my #1 screw. It is always positioned over the center of the #1 jaw. There should have been a black mark left on the face of this Chuck Plate you received. from my experience from 2010, the Chuck Plate will always be centered if your chucks are ok.

if you’re mounting a piece for a natural edge with bark, you might be hard pressed to see any marks. from what I read in your description, it sounds like you are using a flat piece of wood as the rim, lip or opening. That would definitely leave spots on the area of Chuck Plate contact, but difficult to locate on smooth faced wood.

I just uploaded another video on youtube, https://www.youtube.com/edit?video_id=3i2kIBtGcwk&feature=em-upload_owner. It’s what I use and how I do one of my natural edge hollow forms. No turning or anything, just hopefully instruction instead of confusion.

Subscribe to my youtube channel, Nubsnstubs, and go through some of the videos there if you can stand listening to me. There might be something of value in at least one of them…........ ............... Jerry (in Tucson)

-- Jerry (in Tucson) www.woodturnerstools.com

View Woodknack's profile

Woodknack

12369 posts in 2521 days


#5 posted 09-16-2017 07:46 PM

It’s a clever invention

-- Rick M, http://thewoodknack.blogspot.com/

Have your say...

You must be signed in to reply.

DISCLAIMER: Any posts on LJ are posted by individuals acting in their own right and do not necessarily reflect the views of LJ. LJ will not be held liable for the actions of any user.

Latest Projects | Latest Blog Entries | Latest Forum Topics

HomeRefurbers.com