LumberJocks

All Replies on Favorite Forstner bit?

  • Advertise with us
View mramseyISU's profile

Favorite Forstner bit?

by mramseyISU
posted 08-10-2017 12:53 PM


8 replies so far

View builtinbkyn's profile

builtinbkyn

2636 posts in 1089 days


#1 posted 08-10-2017 01:00 PM

Colt Maxicut are hands down the best bits, however they’re very pricy. Buy you can purchase just the 7/8” bit if clean holes are important. Link

-- Bill, Yo!......in Brooklyn & Steel City :)

View mramseyISU's profile

mramseyISU

551 posts in 1694 days


#2 posted 08-10-2017 01:14 PM



Colt Maxicut are hands down the best bits, however they re very pricy. Buy you can purchase just the 7/8” bit if clean holes are important. Link

- builtinbkyn

Those were the ones I was looking at.

-- Trust me I'm an engineer.

View builtinbkyn's profile

builtinbkyn

2636 posts in 1089 days


#3 posted 08-10-2017 04:12 PM


Colt Maxicut are hands down the best bits, however they re very pricy. Buy you can purchase just the 7/8” bit if clean holes are important. Link

- builtinbkyn

Those were the ones I was looking at.

- mramseyISU

I purchased one – 2 1/4”. It cuts like a charm and doesn’t generate any heat. So no burning in difficult woods. They are expensive and a set is really expensive. I’ll pick them up individually as I need them to replace my very old and used Porter Cable bits.

-- Bill, Yo!......in Brooklyn & Steel City :)

View waho6o9's profile

waho6o9

8434 posts in 2725 days


#4 posted 08-10-2017 04:14 PM

Colt

View TheFridge's profile

TheFridge

10360 posts in 1635 days


#5 posted 08-10-2017 04:27 PM

I have one colt and I am going to convert them all one of these days.

-- Shooting down the walls of heartache. Bang bang. I am. The warrior.

View WayneC's profile

WayneC

13775 posts in 4246 days


#6 posted 08-10-2017 05:39 PM

How deep?

-- We must guard our enthusiasm as we would our life - James Krenov

View JohnMcClure's profile

JohnMcClure

254 posts in 789 days


#7 posted 08-10-2017 05:43 PM

I have a super-cheap porter cable set too, but recently I needed to drill several 1-1/8” holes. I bought Amazon’s cheapest (CMT brand), which couldn’t even cut. I returned it and bought the Freud PB (Precision Shear) bit – it worked like a dream. Plowed 1.5” deep in red oak in my cheap DP, in a single plunge – didn’t even have to back out for chips.

-- I'd rather be a hammer than a nail

View HorizontalMike's profile

HorizontalMike

7770 posts in 3063 days


#8 posted 08-10-2017 09:25 PM

Sorry but I burnt way to many forstner bits with little 8” DP over the last 21-22 yrs until i FINALLY purchased a 20” DP from Grizzly. 21yr was ENOUGH. Wish I had done this 10 or20yr ago… Seriously! Just my two cents…

-- HorizontalMike -- "Woodpeckers understand..."

Have your say...

You must be signed in to reply.

DISCLAIMER: Any posts on LJ are posted by individuals acting in their own right and do not necessarily reflect the views of LJ. LJ will not be held liable for the actions of any user.

Latest Projects | Latest Blog Entries | Latest Forum Topics

HomeRefurbers.com