LumberJocks

All Replies on Kitchen Table taper leg bead

  • Advertise with us
View Jeff's profile

Kitchen Table taper leg bead

by Jeff
posted 1511 days ago


16 replies so far

View a1Jim's profile

a1Jim

112000 posts in 2179 days


#1 posted 1511 days ago

Hey Jeff
Some how I’m kinda underwhelmed about tapered legs on this size table , to me it makes it look rather top heavy. You and your wife are the customers in this case and you know what they say about the customer always being right.

-- http://artisticwoodstudio.com Custom furniture

View schloemoe's profile

schloemoe

688 posts in 1540 days


#2 posted 1511 days ago

You know just a thought maybe there is someone in you’re area that will rent a lathe and you could make you’r own legs.

-- schloemoe, Oregon , http://www. woodrehab.blogspot.com

View CaptainSkully's profile

CaptainSkully

1190 posts in 2160 days


#3 posted 1510 days ago

David Marks grooved the legs while they were still square on the table saw, then cut the tapers. The groove supported the beefier bead that set into the groove, and only the profile showed.

-- You can't control the wind, but you can trim your sails

View MisterCat's profile

MisterCat

22 posts in 1525 days


#4 posted 1510 days ago

To play the devils’ advocate, you might want to look at places like Rockler that sell table legs, especially for the turned legs from the top picture. The pine variety runs about $30/each which seems pretty reasonable. The obvious downside to this is that you didn’t make it yourself and the legs are likely imported.

The upside is that you get to do all of the joinery, make the table top, and your project looks like the idea your wife had. That last one is what would be the tipping point for me, as I have zero decorating skills.

My 2 cents,
MisterCat

View CharlieM1958's profile

CharlieM1958

15664 posts in 2820 days


#5 posted 1510 days ago

I like the round legs better, but I understand your predicament. I think the tapered leg design would still look good, but maybe a hair less beefy than in your drawing.

-- Charlie M. "Woodworking - patience = firewood"

View a1Jim's profile

a1Jim

112000 posts in 2179 days


#6 posted 1510 days ago

If you have a turning club close by maybe the could help. I’ve also seen plans for shop built lathes

-- http://artisticwoodstudio.com Custom furniture

View Knothead62's profile

Knothead62

2345 posts in 1563 days


#7 posted 1510 days ago

www.adamswoodproducts.com
www.osbournewood.com

Try these two sites.

View Eli's profile

Eli

141 posts in 1608 days


#8 posted 1510 days ago

I don’t see any reason not to do a short grain bead, so the grain is the same direction as the leg. I did this on a piece and it worked fine, as far as I know.

Eli

View j_olsen's profile

j_olsen

155 posts in 1773 days


#9 posted 1510 days ago

Here’s another source

http://www.tablelegs.com

-- Jeff - Bell Buckle, TN

View Jeff's profile

Jeff

114 posts in 1516 days


#10 posted 1510 days ago

Great suggestions everyone, but after price checking the suggested sites, and local turners, it is too big of an expense for the legs, especially since I already have the lumber for them (for non turned legs). My wife has demoted it on the honey-do list as she wants the round legs. I can’t argue with the customer (and boss) on this one.

I did attempt the ‘ole “Well for just a little more I could get a lathe and turning tools and then learn how to turn etc…” but it didn’t work this time.

I did bookmark those sites though as there are some neat products that I could see using on other projects (the half spindles, etc..)

-- Jeff

View lanwater's profile

lanwater

3075 posts in 1536 days


#11 posted 1510 days ago

Good choice (demotion). The design with the tapper looks really bulky.

-- Abbas, Castro Valley, CA

View jlsmith5963's profile

jlsmith5963

297 posts in 1950 days


#12 posted 1507 days ago

Jeff

The design issue here is not taper vs round, it’s proportions. Because the edge of the corner of the taper will make the taper leg ‘read’ more massive than the round leg you must adjust the proportion of the tapered leg to offset this reading. For example, in comparing the size of the tapered leg with the circular leg the circle should inscribe the square (at it’s largest dimension). Thus when you look at the broadest dimension of the tapered leg (across it’s diagonal) it will the same size as the round leg. Also, the lack of profiling of the tapered leg doesn’t allow any visual relief to the mass (something the round leg as quite a bit of). If you would further develop the design to include a foot and a transition to the apron it would further reduce the visual mass.

-- criticism: the art of analyzing and evaluating the quality of an artistic work...

View Jeff's profile

Jeff

114 posts in 1516 days


#13 posted 1506 days ago

You’ve got something there jlsmith5963. I might play around with the foot and transition ideas in Sketchup a little in the future. The plan is still on hold as my wife wants round legs (full stop). What did you have in mind for the transition to the apron? Something like a scrollsawn arch?

-- Jeff

View CaptainSkully's profile

CaptainSkully

1190 posts in 2160 days


#14 posted 1506 days ago

The rule I use is to taper down 1/2 the the original thickness, so a 4×4 would taper from the bottom of the apron to about 2×2, with only the inside faces being tapered.

-- You can't control the wind, but you can trim your sails

View araldite's profile

araldite

187 posts in 2006 days


#15 posted 1506 days ago

If there’s a woodworkers guild or club in your area, you might want to consider joining. They often have well equipped shops where members can use tools they don’t have at home. Additionally, other members would most likely be glad to help you learn how to turn those legs. Plus there would be all the benefits you get for joining any club.

-- Failure is the road to success if you learn to learn from your mistakes - Vince, Greenville, SC

View Timthemailman's profile

Timthemailman

301 posts in 1378 days


#16 posted 1372 days ago

Have you tried to make a prototype out of a couple of cheap 2 X 4’s gluded together. seeing is believing. Good Luck

Have your say...

You must be signed in to reply.

DISCLAIMER: Any posts on LJ are posted by individuals acting in their own right and do not necessarily reflect the views of LJ. LJ will not be held liable for the actions of any user.

Latest Projects | Latest Blog Entries | Latest Forum Topics

HomeRefurbers.com

Latest Projects | Latest Blog Entries | Latest Forum Topics

GardenTenders.com :: gardening showcase