LumberJocks

All Replies on painting a shop

  • Advertise with us
View HokieMojo's profile

painting a shop

by HokieMojo
posted 1574 days ago


25 replies so far

View JimNEB's profile

JimNEB

239 posts in 1670 days


#1 posted 1574 days ago

I read a post about someone who used Kilz to paint the walls of the shop. I’m thinking about doing that also when I get to that point. I’m planning on putting wafer board up instead of dry wall. I figured that would be more durable and I could hang things on it easier. I’d paint it a light color, I’m going white. I think that helps with the lighting.

-- Jim, Nebraska

View SnowyRiver's profile

SnowyRiver

51451 posts in 2082 days


#2 posted 1574 days ago

I know that gloss paint cleans up a lot easier than flat, but it is glossy. I used white gloss in my daughters room a few years ago and it was pretty shiny

-- Wayne - Plymouth MN

View 8iowa's profile

8iowa

1489 posts in 2363 days


#3 posted 1574 days ago

The walls and ceiling of my “Workshop in the Woods” are paneled with OSB, which is more durable than sheet rock,. I primed the surfaces using a sprayer, and then rolled on two coats of semi-gloss white. This really inhances the lighting, and has been said, cleans up easier than flat paint.

-- "Heaven is North of the Bridge"

View dbhost's profile

dbhost

5378 posts in 1834 days


#4 posted 1574 days ago

If I had, say a warehouse to move my shop into while I finished the garage as a dedicated shop space I would do the following…

#!. Yank every single bit of sheet rock off of the exterior walls. #2. Insulate #3. Run a sub panel and power circuits where they need to go. #4. Strip the floor dead bare, and do an epoxy coating on it. In all likelyhood something neutral like Beige. Not my preference, but certainly would make the house easier to sell in the long run. #5. Rip down the drywall around the attic ladder, pull out current attic ladder and install a 30” HEAVY DUTY insulated ladder / framing. #6. Re rock the whole thing. #7. Finish mounting my ceiling lighting so that the anchors are there. #8. Pull the ceiling lighting, and outlet covers. #9. Prime, prime, prime. #10. Paint. Preferrably an interior semi gloss pure white. At least 2 coats to insure even color. #11. Reinstall lighting, outlet covers etc… #12. Install “tool stacker” rack. #13. Install lumber rack #14. Install dust collection ductwork, cord winders, and hose reels. #15. Install peg boards, clamp racks, etc… #16. Move tools, lumber etc… back in. #17. Insulate the garage doors. #18. Get it disasterously messy again with projects.

-- My workshop blog can be found at http://daves-workshop.blogspot.com

View MrWoody's profile

MrWoody

305 posts in 2376 days


#5 posted 1574 days ago

I just painted mine last fall after 20 years of unpainted dry walland no windows. I primed it to deal with the yellow sheet rock and still relatively white mud. Then I purchased an acrylic high gloss white with new fluorescent lighting I was afriad it would be too much. Once you start hanging stuff on the walls it is not nearly as stark as you would expect. It is nice going in there now that it isn’t so dingy.

-- If we learn from our mistakes, I'm getting a fantastic education.

View Alexander's profile

Alexander

190 posts in 1713 days


#6 posted 1574 days ago

Kills and Z prime are a primer and sealer. You can even cover the smell of smoke with Kills or z prime.
Satin finish will allow good clean up but not glare from lights. Light can not go around or over lump or high spots in your surface. A statin finish breaks the light up to not show the bad finish.

-- John at Sugarloft Mountain........Don't argue with an idiot; people watching may not be able to tell the difference.

View Wintersedge's profile

Wintersedge

83 posts in 1576 days


#7 posted 1574 days ago

I think a lot depends on what you are doing, how much natural like you have, and what type of lighting you have.

If you have HO(high output) bulbs in either t5 or t8, I would stay away from a high gloss, the same is also true if you have yellow spectrum fluorescent bulbs. I might be jaded because I wear glass with goggles so I tend to see reflections and a bit of glare. No harm to your eyes, I just find it irritating after a while.

You 100% do not want to go flat.

Eggshell, satin, and semi-gloss all clean up nicely.
Eggshell you can clean with a good bit of scrubbing.
Satin can be cleaned, but you can not scrub too hard or you will pull the paint off
semi-gloss cleans easier, but is also the most expensive.

I just reread your post and it seems you have bare drywall. I would absolutely suggest you go with a primer coat first and tint it the shade/hue you want. That will give you a great idea of what your light reflection will look like, you always want to prime before you paint, and bare drywall is gonna absorb more paint why not through cheaper primer at it first. In the end you may like the primer coat.

If you want to burn 20 bucks, you could always get the pint size cans, paint different walls with each can and go with the one that you like best.

-- Motivation alone is not enough. If you have an idiot and you motivate him, now you have a motivated idiot.

View Rick  Dennington's profile (online now)

Rick Dennington

3272 posts in 1796 days


#8 posted 1574 days ago

Greetings: Sheetrock for walls and ceiling?....... bad idea…. You’ll never be able to hang anything heavy like cabinets, shelves, ceiling lights, etc. without the screws pulling out over time. Walls need something like OSB or something more suitable for shop needs. As for painting…. 2 coats of Kilz, and 2 coats of a flat latex white…that’ll do it. Don’t worry, you ain’t gonna be vacumning the walls, so it really don’t matter what you go with…. do what you want to….. it’s your shop…... keep on keeping on…...... later.

-- " I started with nothing, and I've still got most of it left".......

View HokieMojo's profile

HokieMojo

2097 posts in 2330 days


#9 posted 1573 days ago

All good ideas, but I’m definitely going with sheetrock. I like the flame resistant properties, plus it is an attached garage so the building code may even require drywall instead of osb. If I need to hang heavy stuff, I’ll just use a wall stud. I plan to leave the indentations caused by drywall screws (I won’t put mud over them) so that the studs will remain easy to find.

As for paint, I guess I’m going to prime it white. If I’m happy with the looks, I’ll leave it at that. If not, I’ll throw on some white paint afterward. I just REALLY dislike the tan look of the 20 year old sheetrock that I do have and seeing the back of the exterior sheathing in the uncovered areas. I think anything will be an improvement.

View Abbott's profile

Abbott

2570 posts in 1906 days


#10 posted 1573 days ago

Flat white paint reflects more light then semi-gloss or gloss paint. But semi-gloss and gloss wear a lot better and clean up is much easier. I also plan to paint my shop this summer. The walls are sheeted with oxboard and the lid is Sheetrock. I don’t plan to paint the ceiling so there will be no need mask or remove air and electrical lines.

I will move all my equipment and everything else I can to the center of the shop. Then clear the walls and stack what I can on top of the stuff in the center of the shop. Everything else will be moved outside or into the garage.

To make masking the ceiling easier there are folded plastic sheets available in small rolls about 6” wide and 25” or better long with masking tape already attached. You can mask along an edge with this then fold out the plastic to 3’ or 8’ in width depending on what width you feel you need. I plan to use 3’ rolls all around the top of my ceiling (where the walls meet it) then pin it to the ceiling with small pieces of blue tape. Blue masking tape has less glue on it and will not pull other paint or drywall paper off as bad as regular masking tape will. This will give me a 3’ shield (masked area) all around the ceilings perimeter. The built in work benches will be masked next except the legs which I also want primed. I will then mask the exposed concrete slab with plastic sheets and toss a couple of wide sheets over the large pile of gear in the center of the shop.

I plan to spray all of the walls and cabinets with two coats (probably three) of Kilz brand primer/sealer, stain blocker. Wal-mart also has a brand that used to be a lot cheaper then Kilz but now costs almost as much. It’s probably the same stuff with a different label. Oil base covers the best and is much more durable then water base latex. Latex works ok and is a lot easier to use then oil base. It’s always a trade off. I won’t decide what I am going to use until I purchase it. I often go with oil base because of the much superior durability but you also have to use thinner to clean up after which adds time and expense to the job. Drying time between oil base coats is also longer.

After several coats of the flat off-white is applied and dry I will may or may not spray a coat of semi-gloss paint over it. I will then go back in pull the masking and paint a couple of coats of trim paint on whatever it is I want to detail out. This is where gloss or semi-gloss helps a bunch. Door and window casing, window sills and doors themselves all get a coat or two of paint with gloss. Wherever extra wear and finger prints will be.

The amount of reflected light off of the painted surfaces will triple (or better) after you paint.

-- Ohh mann...pancakes and boobies...I'll bet that's what Heaven is like! ♣ ♣ ♣ ♣

View Abbott's profile

Abbott

2570 posts in 1906 days


#11 posted 1573 days ago

All good ideas, but I’m definitely going with sheetrock. —Hokie

It has to be 5/8” type X Sheetrock for a one hour fire rating. Only ceilings and party walls (the wall between the garage and the house) are required by code to have a fire rating in most areas. Sometimes party walls are required to have a two hour fire rating which is two layers of 5/8”.

My shop is a stand alone building with a 5/8” lid because the ceiling joists (trusses) are on 24” centers. Half-inch rock on a ceiling with 24” centers will sag to much.

-- Ohh mann...pancakes and boobies...I'll bet that's what Heaven is like! ♣ ♣ ♣ ♣

View TheDane's profile

TheDane

3658 posts in 2265 days


#12 posted 1573 days ago

My garage was insulated and sheet-rocked, but never painted. When I bought the place, I painted it with Kilz, followed by two coats of white semi-gloss interior paint.

-- Gerry -- "I don't plan to ever really grow up ... I'm just going to learn how to act in public!"

View Bearpie's profile

Bearpie

2584 posts in 1620 days


#13 posted 1573 days ago

I used OSB in my workshop, caulked all corners and seams then used Kilz primer that was tinted sort of light yellow(I’m partial to that color) and rolled 2 coats on the walls. then put tiles(not ceramic kind) on the floor to make it easy to clean. I’m happy, that’s what counts!

Erwin Jacksonville, Fl

-- Erwin, Jacksonville, FL

View Ken90712's profile

Ken90712

14821 posts in 1791 days


#14 posted 1573 days ago

I painted my shop tan with semi-gloss. ( saw dust color) Flat is too hard to wipe down, or keep clean. I use white on the table tops to brighten it up plus I have 3 windows. Good luck in what ever you choose.

-- Ken, "Everyday above ground is a good day!"

View Edziu's profile

Edziu

150 posts in 1653 days


#15 posted 1572 days ago

Hello. For fresh drywall: I would definitely prime with a drywall sealer. I believe Behr makes one in either a purple or orange can. Make sure you get the one for fresh drywall. Finish coat sheens are really personal preference, but cleaning an eggshell is the easiest.

What’s all this noise about OSB on garage walls? It’s a gross texture and soaks up paint like a SOB. As for hanging things…Are houses being built without studs now; can’t you just find a stud to put a screw in? I’ve got three courses of brick to contend with on the four walls of my shop, so hanging anything is a nightmare.

View Moron's profile

Moron

4666 posts in 2495 days


#16 posted 1572 days ago

I would prefer to spend my money on tools and tooling so I skip the paint entirely and just buy another light bulb thats cheap and save my $$$$ for other things.

maybe some day I will win a small loittery cause a nice bright room….....

dreaming

-- "Good artists borrow, great artists steal”…..Picasso

View Dark_Lightning's profile

Dark_Lightning

1671 posts in 1711 days


#17 posted 1572 days ago

Polyvinyl acetate (PVA) primer over the drywall and taped up parts. It’s cheaper than KILZ. It is only a sealer for the paint. One coat. Then, a personal recommendation: Flat white: no tint, no shine. This is because you don’t want glare (specular reflection, also known as shiny spots), or to look at crappy taping work if it is present-shiny shows that up. Scrubbing isn’t an issue in a woodshop, dust is, and if you want dust it off, you can vacuum it. Flat white paint requires less lighting, leading to reduced electrical costs.

Note: paint is NOT a primer/sealer, each serve a different purpose. You can paint to your heart’s delight, but one coat of PVA type sealer will give a good base for you final coat.

View patron's profile

patron

12964 posts in 1943 days


#18 posted 1572 days ago

semi-gloss interior white or off white ,
high-hide maintenance paint ,
from wal-mart ,
5 gallon bucket , $ 50.00 !
goes on like rubber ,
stays put !

-- david - only thru kindness can this world be whole . If we don't succeed we run the risk of failure. Dan Quayle

View John Gray's profile

John Gray

2370 posts in 2487 days


#19 posted 1572 days ago

Interesting post I plan on following it as my shop needs paint. Thanks for posting!

-- Only the Shadow knows....................

View Abbott's profile

Abbott

2570 posts in 1906 days


#20 posted 1572 days ago

”Flat white paint reflects more light then semi-gloss or gloss paint.”

No offense but everything I could find says different about this, was wondering how this is so?
————————————————————————————————————————————————————————————————————————-

“Flat white paint has the ability to reflect between 75-85% of the light, and does not create hotspots.

Glossy and eggshell whites do not reflect light as efficiently as flat white. Semi-gloss paint for example, only has the ability to reflect between 55-60% of the light.”

This is measured with a light meter.

-- Ohh mann...pancakes and boobies...I'll bet that's what Heaven is like! ♣ ♣ ♣ ♣

View Abbott's profile

Abbott

2570 posts in 1906 days


#21 posted 1572 days ago

I am on my second shop with OSB walls. The first one I ran OSB over the existing sheetrock because of the extra strength it provides against damage. OSB loves to suck up the light so I will be painting my current shop this summer. I won’t paint the sheetrock ceiling, just the OSB walls. I then plan to trim it out just to make it look nice. I thought over just adding another 600-1000 watts of light but decided that the paint would look better and that I wouldn’t have to add any more light fixtures.

-- Ohh mann...pancakes and boobies...I'll bet that's what Heaven is like! ♣ ♣ ♣ ♣

View doordude's profile

doordude

1085 posts in 1585 days


#22 posted 1572 days ago

hey,hokiemojo; might as well throw in my two cents
old sheet rock needs to be sealed preferably with oil base primer. this also seals the new mud ,giving your satin or semi gloss paint to stick and bond . if its asmall garage by the time put tools and your nice cabinet tool holders threr won’t be
much reflection except from the ceiling.
why leave the nail dimpples showing? two coats with a 6” knife and lightly sand with 220, then paint.
your trying to elevate your work enviorment,right? also i would roll the paint. no more than 40 minutes each coat,
you need a stud finder for $20.00 to find the studs for french cleats, or any thing you want to hang latter
shoot for the moon,it’s only time and money!

View Rick  Dennington's profile (online now)

Rick Dennington

3272 posts in 1796 days


#23 posted 1572 days ago

Greetings Hokiemojo: Let me just say this with parting grace…... it’s your shop, do what you want to with it…... makes me no difference, cause I really don’t care. You’ll do it the way you want to anyhow, so go for it….. I would. All the sugesstions in the world ain’t gonna matter. It’s your $’s… keep on keeping on..later.

-- " I started with nothing, and I've still got most of it left".......

View ND2ELK's profile

ND2ELK

13495 posts in 2376 days


#24 posted 1572 days ago

I painted my walls and ceiling with flat off white latex paint. It is easy to touch up if needed.

God Bless
tom

-- Mc Bridge Cabinets, Iowa

View HokieMojo's profile

HokieMojo

2097 posts in 2330 days


#25 posted 1571 days ago

Rick,
I agree that I will do things the way I want, but good ideas/suggestions will influence me. For example, I think I’ll just do one prime coat. I’ll then probably do one finish coat and leave it at that. Since it will just be an off white. Thats already 2 coats less than I originally thought I’d need. I also like the idea of an eggshel instead of the original “flat” due to washability, but I still don’t like gloss or semi-gloss, no matter how easy it is to clean.

I really like all the opinions. No matter how many, I still like hearing more. All this stuff will get a bit grungy and take a beating, but its got to be better than what I’ve got now.

Have your say...

You must be signed in to reply.

DISCLAIMER: Any posts on LJ are posted by individuals acting in their own right and do not necessarily reflect the views of LJ. LJ will not be held liable for the actions of any user.

Latest Projects | Latest Blog Entries | Latest Forum Topics

HomeRefurbers.com

Latest Projects | Latest Blog Entries | Latest Forum Topics

GardenTenders.com :: gardening showcase