LumberJocks

All Replies on Trim router dust colkextion

  • Advertise with us
View Medickep's profile

Trim router dust colkextion

by Medickep
posted 12-22-2016 10:36 PM


7 replies so far

View EricTwice's profile

EricTwice

230 posts in 438 days


#1 posted 12-22-2016 11:01 PM

Most all of the dust collection systems I’ve used/seen have been bulky and unwieldy. To me control is the most important thing and they fly in the face of this. Personally I’d rather have the small and handy trim router and clean up the mess after.

just my personal opinion

I’ve added this to my watch list so I can see if anyone knows of a dust collection system for one of these that isn’t awkward.

-- nice recovery, They should pay extra for that mistake, Eric E.

View eflanders's profile

eflanders

240 posts in 1755 days


#2 posted 12-22-2016 11:13 PM

My trim router came with a dust extractor attachment and it gets only about 60% of the stuff. While this is better than nothing, it does block your view a lot when in use. So sometimes the plusses don’t outweigh the minuses…

View MrUnix's profile (online now)

MrUnix

6346 posts in 2103 days


#3 posted 12-22-2016 11:21 PM

Let them chips fly… DC on a router is a PITA and can effect your control of the tool. If you want DC for your router, build a router table for it.

Cheers,
Brad

-- Brad in FL - In Dog I trust... everything else is questionable

View Elementz's profile

Elementz

2 posts in 439 days


#4 posted 12-22-2016 11:31 PM

I have found that it is almost easier to just rig something up with a shop vac or a modified down draft table.
I can agree with most of the comments on here about blocking view and not collecting enough. If you are doing smaller projects why not just save your money, deal with a little more mess and try to use a McGiver’ed rig up.

-- Instagram: @Elementz_Alchemist

View clin's profile

clin

797 posts in 901 days


#5 posted 12-22-2016 11:35 PM

I have the Dewalt 611 and use the dust collector most of the time. I think it works well. Nothing gets everything, and this is no different. But every once in awhile I’ll use it without the DC and it reminds me just how well the DC actually works.

But,as others have said, having a hose connected does make the router harder to control. I use a small hose and transition to a larger one of my shop vac. But even then, sometimes I have to clamp the hose to the table so the hose isn’t trying to fall off the table and therefore pull the router.

I do tend to grasp the hose and router at the same time in order to support he hose connection.

It the weight of the hose pulling sideways on the router that is the issue. While I’ve not done, I think if I put a hanger on the ceiling, above the workbench, and had the hose coming down, that would work really well. Or of course if using a full blown DC system, having a port above the bench would be useful.

-- Clin

View pintodeluxe's profile

pintodeluxe

5566 posts in 2718 days


#6 posted 12-23-2016 12:11 AM

I have the 611 with dust attachment, and it works well for dados and inboard cuts. For edge profiling it won’t capture all the chips. I usually use the 618 if I want dust collection while hand routing.

-- Willie, Washington "If You Choose Not To Decide, You Still Have Made a Choice" - Rush

View Medickep's profile

Medickep

569 posts in 1643 days


#7 posted 12-23-2016 01:08 AM

Thanks guys for the advice! I think I’ll let the chips fly until festool makes a real trim router that works!

-- Keith

Have your say...

You must be signed in to reply.

DISCLAIMER: Any posts on LJ are posted by individuals acting in their own right and do not necessarily reflect the views of LJ. LJ will not be held liable for the actions of any user.

Latest Projects | Latest Blog Entries | Latest Forum Topics

HomeRefurbers.com