LumberJocks

All Replies on Asking Toys and Joys truck builders

  • Advertise with us
View Dee1's profile

Asking Toys and Joys truck builders

by Dee1
posted 12-20-2016 12:49 AM


16 replies so far

View JAAune's profile

JAAune

1853 posts in 2517 days


#1 posted 12-20-2016 01:49 AM

Use angled cauls like those shown in the picture below. There are various ways to achieve this. You can glue the cauls to plywood then clamp the plywood to the workpiece. It’s also possible to glue them right to your project with PVA and a piece of paper between the caul and the wood. The paper allows the parts to be separated easily.

-- See my work at http://remmertstudios.com and http://altaredesign.com

View tealetm's profile

tealetm

103 posts in 1058 days


#2 posted 12-20-2016 02:37 AM

Have you tried tape?

View LittleBlackDuck's profile

LittleBlackDuck

2086 posts in 1021 days


#3 posted 12-20-2016 03:44 AM


Have you tried tape?

- tealetm

tealetm has it all taped up. I have found that for most mitre joints a good dose of tape (blue tape not duct) will seal the deal. If you need strength in the joint try, re-enforcing with dowels or splines (even slivers will do). Even a 1/16” or 1/8” dowel does wonders.

PS. Nice looking cab!!!....

-- If your first cut is too short... Take the second cut from the longer end... LBD

View crowie's profile

crowie

2740 posts in 2151 days


#4 posted 12-20-2016 08:43 AM

Just a thought…would you be able to biscuit join those pieces????

-- Lifes good, Enjoy each new day...... Cheers from "On Top DownUnder" Crowie

View Dutchy's profile

Dutchy

3147 posts in 2369 days


#5 posted 12-20-2016 12:20 PM

View gwilki's profile

gwilki

226 posts in 1674 days


#6 posted 12-20-2016 02:43 PM

Funny you should ask. I built that same model and a dump truck a couple of years ago. To “clamp” those joints, I just put a couple of dabs of CA glue at the ends of the pieces. Then, I spread the PVA glue between those dots. When I pushed the together, the CA set in 10 seconds and held the joint in place until the PVA added the stronger joint that I wanted. I’ve used this method several times now for tricky joints and it’s always worked well.

-- Grant Wilkinson, Ottawa ON

View DS's profile

DS

3032 posts in 2621 days


#7 posted 12-20-2016 02:50 PM

If you are building up your tool set, these are really handy.
Mine don’t see a lot of action, but when they do, they are invaluable.

-- "Hard work is not defined by the difficulty of the task as much as a person's desire to perform it.", DS251

View Dee1's profile

Dee1

302 posts in 2089 days


#8 posted 12-20-2016 04:11 PM

Hey this is a great forum what a great bunch of responses
I have never used the blue tape, and I tries it and I think we have a winner. thank all you guys all great ideas.
Thanks again
Dee

View LittleBlackDuck's profile

LittleBlackDuck

2086 posts in 1021 days


#9 posted 12-20-2016 04:41 PM


....
I have never used the blue tape, ....

- Dee1


Just don’t be too stingy with the blue tape… especially on the underside (not like I have tried to draw)...

Lay the tape sticky side up (unless you want to stick your bench)... but the mitre ends together (flat)... add glue… draw mitre joint together… secure/tigten with blue tape on the other side (preferably “loosely” placed before glue up… and pulling the joint together)....
Just watch out for sharp edges that may cut the tape if pulling TOO tight. It is quite surprising the pressure you can apply (within reason).

-- If your first cut is too short... Take the second cut from the longer end... LBD

View GR8HUNTER's profile

GR8HUNTER

5121 posts in 913 days


#10 posted 12-20-2016 04:57 PM

I also had the same question here all my responses I got back

http://lumberjocks.com/topics/167810

-- Tony---- Reinholds,Pa.------ REMEMBER TO ALWAYS HAVE FUN

View crowie's profile

crowie

2740 posts in 2151 days


#11 posted 12-20-2016 11:31 PM



If you are building up your tool set, these are really handy.
Mine don t see a lot of action, but when they do, they are invaluable.

- DS

What brand are they and Were did they come from please “DS” .... thank you

-- Lifes good, Enjoy each new day...... Cheers from "On Top DownUnder" Crowie

View htl's profile

htl

4230 posts in 1360 days


#12 posted 12-21-2016 12:15 AM

Funny you should ask. I built that same model and a dump truck a couple of years ago. To “clamp” those joints, I just put a couple of dabs of CA glue at the ends of the pieces. Then, I spread the PVA glue between those dots. When I pushed the together, the CA set in 10 seconds and held the joint in place until the PVA added the stronger joint that I wanted. I ve used this method several times now for tricky joints and it s always worked well.

- gwilki

gwilki I’ve been using this trick more and more on my builds to add strength [wood glue] and speed [super glue] it’s a winning combination.. *And after it was dry I still drilled it for two small dowels just to be safe, mine has a split track so felt like it might need it.. *

-- An Index Of My Model making Blogs http://lumberjocks.com/htl/blog/116729

View Lazyman's profile

Lazyman

2629 posts in 1588 days


#13 posted 12-21-2016 03:03 AM

How about a pair custom corner clamp that are made from scraps to hold the 2 pieces at the correct angle. See this video by Izzy Swan to see what I mean. Yours would be made for the angles of you project rather than 90 degrees of course. It doesn’t have to be as elaborate or reusable as his but you just need one on both sides to hold them at the correct angle while you apply pressure to the glue joint. I you add a block to the clamp you may also be able to use a regular F clamp to apply a little pressure.

I would also add a spline to the joints. Gluing end grain to end grain will not hold very well no matter how perfect you are able to clamp it and a spline will give you side grain glue surfaces to greatly increase the strength of the joint. The spline will also make it so it is less likely to slide apart while clamping it.

Nice work by the way.

-- Nathan, TX -- Hire the lazy man. He may not do as much work but that's because he will find a better way.

View DS's profile

DS

3032 posts in 2621 days


#14 posted 12-21-2016 06:29 PM

Crowie, now you’re making me scratch my head as to where I got mine from. I think I found them on Amazon for a discounted price.

The image I posted was from Woodcraft and is a bit more money.

-- "Hard work is not defined by the difficulty of the task as much as a person's desire to perform it.", DS251

View crowie's profile

crowie

2740 posts in 2151 days


#15 posted 12-21-2016 09:49 PM



Crowie, now you re making me scratch my head as to where I got mine from. I think I found them on Amazon for a discounted price.

The image I posted was from Woodcraft and is a bit more money.

- DS

Thank you sir..
Hopefully no splinters just sawdust..
Happy Christmas from the Great Southern Land…

-- Lifes good, Enjoy each new day...... Cheers from "On Top DownUnder" Crowie

View Lazyman's profile

Lazyman

2629 posts in 1588 days


#16 posted 12-27-2016 03:01 AM

Hey. I just noticed these clamping blocks from lee valley
http://www.leevalley.com/en/Wood/page.aspx?p=70643&cat=1,43838
You could probably make your own.

-- Nathan, TX -- Hire the lazy man. He may not do as much work but that's because he will find a better way.

Have your say...

You must be signed in to reply.

DISCLAIMER: Any posts on LJ are posted by individuals acting in their own right and do not necessarily reflect the views of LJ. LJ will not be held liable for the actions of any user.

Latest Projects | Latest Blog Entries | Latest Forum Topics

HomeRefurbers.com