LumberJocks

All Replies on Kreg tables

  • Advertise with us
View Woodchuck2010's profile

Kreg tables

by Woodchuck2010
posted 11-16-2016 02:43 AM


15 replies so far

View Heywood's profile

Heywood

46 posts in 1593 days


#1 posted 11-16-2016 04:18 AM

Who did you get them through? I dig Kreg products

View Woodchuck2010's profile

Woodchuck2010

721 posts in 1002 days


#2 posted 11-16-2016 04:48 AM

Peachtree woodworking supply. I like Kreg too. I have a few of their products. All great stuff.

-- Chuck, Michigan,

View helluvawreck's profile

helluvawreck

32083 posts in 3011 days


#3 posted 11-16-2016 08:03 PM

These are very nice and can be used for a variety of purposes. They’re good quality and will make a nice addition to your shop.

helluvawreck aka Charles
http://woodworkingexpo.wordpress.com

-- helluvawreck aka Charles, http://woodworkingexpo.wordpress.com

View Heywood's profile

Heywood

46 posts in 1593 days


#4 posted 11-16-2016 10:38 PM

Thanks Chuck

View greenacres2's profile

greenacres2

328 posts in 2312 days


#5 posted 11-17-2016 01:41 AM

I got a pair from Peachtree as well, along with 4 sets of their casters—at $10 a wheel they’re less than the red phenolic plate casters I usually get, and really nice. Am in the midst of a table build, so once I assembled the stands, I screwed 3 8 foot 1×4’s to them to tie them together, threw a sheet of OSB on top of that, and proceeded to lay out the 5” wide boards for a 40” x 106” table top. Rolls around unbelievably easy. Timing was perfect for much needed temporary space.

My more permanent thought is to use one for an outfeed for TS, set another to the height of my RAS on the left side. There are so many ways they could be used, I may try to keep the top surface (whatever I end up doing) kind of easy to change/remove. Nice stuff.
earl

View Woodchuck2010's profile

Woodchuck2010

721 posts in 1002 days


#6 posted 11-17-2016 02:39 AM



I got a pair from Peachtree as well, along with 4 sets of their casters—at $10 a wheel they re less than the red phenolic plate casters I usually get, and really nice. Am in the midst of a table build, so once I assembled the stands, I screwed 3 8 foot 1×4 s to them to tie them together, threw a sheet of OSB on top of that, and proceeded to lay out the 5” wide boards for a 40” x 106” table top. Rolls around unbelievably easy. Timing was perfect for much needed temporary space.

My more permanent thought is to use one for an outfeed for TS, set another to the height of my RAS on the left side. There are so many ways they could be used, I may try to keep the top surface (whatever I end up doing) kind of easy to change/remove. Nice stuff.
earl

- greenacres2

Awesome idea. I do love the versatility.

-- Chuck, Michigan,

View Woodchuck2010's profile

Woodchuck2010

721 posts in 1002 days


#7 posted 11-17-2016 02:39 AM



Thanks Chuck

- Heywood

No problem Heywood!

-- Chuck, Michigan,

View Woodchuck2010's profile

Woodchuck2010

721 posts in 1002 days


#8 posted 11-21-2016 10:40 PM

I’ve started enclosing the stand. I just need to make a couple of doors now.

-- Chuck, Michigan,

View greenacres2's profile

greenacres2

328 posts in 2312 days


#9 posted 11-22-2016 03:09 AM

These came at the right time. 2 Kreg stands with casters, strung together with 3 1×6’s. Table top glue up, 112” x 40” x 1 1/2” thick. Dozen pipe clamps and 3 sets of cauls. Wheels locked and it didn’t move a bit. Unlock them and it moves any direction with one hand. This was a blessing yesterday!!

earl

View Woodchuck2010's profile

Woodchuck2010

721 posts in 1002 days


#10 posted 11-22-2016 01:52 PM



These came at the right time. 2 Kreg stands with casters, strung together with 3 1×6 s. Table top glue up, 112” x 40” x 1 1/2” thick. Dozen pipe clamps and 3 sets of cauls. Wheels locked and it didn t move a bit. Unlock them and it moves any direction with one hand. This was a blessing yesterday!!

earl

- greenacres2

Great job! I like it!

-- Chuck, Michigan,

View greenacres2's profile

greenacres2

328 posts in 2312 days


#11 posted 11-23-2016 02:32 AM

Thanks Chuck. I like the look of the enclosure, and will consider it. One of my stands will get the Kreg assembly top that is on the end of my work bench now. But…during the course of this table build, I’ve clamped si many parts to the 1 by’s that I may keep one open just for that use. When routing the spline grooves, a pair of quick clamps held each board in place—quick change. And another pair of clamps held a plywood scrap that served as a place to set the router. After routing the first one—and having the cord and hose get hung up—I flipped the plywood clamps so the beams pointed up and served to guide the hose and cord.

earl

View Woodchuck2010's profile

Woodchuck2010

721 posts in 1002 days


#12 posted 11-23-2016 02:48 AM

I think a large lower shelf would be excellent and really tie the two tables together while giving you a ton of storage space.

-- Chuck, Michigan,

View Woodchuck2010's profile

Woodchuck2010

721 posts in 1002 days


#13 posted 11-24-2016 07:01 PM

Made the doors. Just have to put some poly on it.

-- Chuck, Michigan,

View greenacres2's profile

greenacres2

328 posts in 2312 days


#14 posted 11-25-2016 02:09 AM

Looks good Chuck.
earl

View Woodchuck2010's profile

Woodchuck2010

721 posts in 1002 days


#15 posted 11-30-2016 08:12 PM

The 2 for 1 deal is still on from Peachtree woodworking. Its good through tonight. Grab ‘em while you can.

-- Chuck, Michigan,

Have your say...

You must be signed in to reply.

DISCLAIMER: Any posts on LJ are posted by individuals acting in their own right and do not necessarily reflect the views of LJ. LJ will not be held liable for the actions of any user.

Latest Projects | Latest Blog Entries | Latest Forum Topics

HomeRefurbers.com