LumberJocks

All Replies on Router lifts

  • Advertise with us
View Stanley Coker's profile

Router lifts

by Stanley Coker
posted 11-15-2016 05:14 PM


20 replies so far

View Fred Hargis's profile

Fred Hargis

5234 posts in 2730 days


#1 posted 11-15-2016 05:28 PM

Also look at the Woodpecker offerings. I’ve had a PRL for quite a few years (it’s outlasted 2 routers) and find their stuff top notch, albeit expensive.

-- Our village hasn't lost it's idiot, he was elected to congress.

View OggieOglethorpe's profile

OggieOglethorpe

1276 posts in 2346 days


#2 posted 11-15-2016 05:39 PM

I have a Woodpecker PRL, but have used others.

I actually prefer the crank mechanism of the Jessem of over the PRL.

View newwoodbutcher's profile

newwoodbutcher

780 posts in 3086 days


#3 posted 11-15-2016 05:59 PM

I also have the PRL and like it but my buddy just got the incra. The PRL is a bit challanging to make fine adjustments. The Incra crank is much more user friendly. If i had to do it over again I would go with Incra.

-- Ken

View WhoMe's profile

WhoMe

1564 posts in 3480 days


#4 posted 11-15-2016 06:14 PM

One of the more important things to consider is too make sure the plate of the lift fits in the cut out in your router table. Rockler is different from jessem and those may be different from woodpeckers.
Another thing to consider is what router motor are you planning to put in the lift and also in the future. The Rockler only fits the mid size routers like the pc 892/690 , bosch 1617 series and other motors that diameter. Where as the incra can fit most mid size routers and the big pc 6518.
If you plan to put a big motor in the lift either now or in the future, by the right lift now and save money in the long run.
If you are considering Rockler vs incra vs bench dog, incra is the best of the three.

-- I'm not clumsy.. It's just the floor hates me, the tables and chairs are bullies, the wall gets in the way AAANNNDDD table saws BITE my fingers!!!.. - Mike -

View ScottM's profile

ScottM

698 posts in 2383 days


#5 posted 11-15-2016 06:17 PM



One of the more important things to consider is too make sure the plate of the lift fits in the cut out in your router table. Rockler is different from jessem and those may be different from woodpeckers.
Another thing to consider is what router motor are you planning to put in the lift and also in the future. The Rockler only fits the mid size routers like the pc 892/690 , bosch 1617 series and other motors that diameter. Where as the incra can fit most mid size routers and the big pc 6518.
If you plan to put a big motor in the lift either now or in the future, by the right lift now and save money in the long run.
If you are considering Rockler vs incra vs bench dog, incra is the best of the three.

- WhoMe

Was just about to give that same “check you table for compatibility” line. Incra says that their lift will not fit Rockler or Bench Dog table cutouts.

View AWood's profile

AWood

51 posts in 3982 days


#6 posted 11-15-2016 06:27 PM

I’ve had the Bench Dog Pro-lit with 3hp Porter Cable wired with 220 running extensively in my hobby shop for 7 years. The router lift is mounted to a Bench Dog router table/table saw extension. The Pro-lift is one solid piece of equipment and I would want nothing less.

-- AllWood

View Kaleb the Swede's profile

Kaleb the Swede

1880 posts in 2206 days


#7 posted 11-15-2016 06:41 PM

https://www.walmart.com/ip/PRO-LIFT-T-9456-3000-Lb-Scissor-Jack/28087368

Heres what i use. Not the most glamorous, but it works well on a plunge router in a kreg router plate. Best part is, it’s much cheaper

-- Just trying to build something beautiful

View Rentvent's profile

Rentvent

151 posts in 1085 days


#8 posted 11-15-2016 06:54 PM

Get a Triton router. It has the lift built in and automatically locks the collet when it is fully elevated.

View joey502's profile

joey502

544 posts in 1754 days


#9 posted 11-15-2016 10:45 PM

I have the Jessem mast r lift, purchased in 2008 and still works perfectly. I also have the Jessem PVC coated phenolic top so the lift matching the top is a non issue.

I can not comment on Woodpeckers as I have no first hand experience with their lifts. The Woodpeckers tools I do have are fantastic though. Jessem and Incra are both on the high end of cost but the quality is worth the asking price. Other than the insert ring design they appear to be copies of one another. You can not go wrong with either the Incra or Jessem lifts.

View Woodchuck2010's profile

Woodchuck2010

723 posts in 1095 days


#10 posted 11-16-2016 02:56 AM

I have the Jessem also and really like it!

-- Chuck, Michigan,

View bonesbr549's profile

bonesbr549

1579 posts in 3303 days


#11 posted 11-16-2016 03:13 AM

I bought the woodpecker PRL back in 2004 or 2005 one of the two. Still using today. I had a part wear out and called wanted to get a replacement. They send me the part no charge. Enough said. Still goin strong today.

-- Sooner or later Liberals run out of other people's money.

View Stanley Coker's profile

Stanley Coker

259 posts in 3432 days


#12 posted 11-16-2016 10:43 AM

Hey everyone, thanks for all the great information and advice on router lifts. I think I am leaning toward the Jessem/Incra. Again thanks for all the info.

-- Stanley, North Georgia

View OggieOglethorpe's profile

OggieOglethorpe

1276 posts in 2346 days


#13 posted 11-16-2016 02:15 PM

I’m pretty sure the Incra and Jessem use the same mechanism. Plate size may vary.

If you look closely, you’ll see the Woodpeckers and Jessem guts in many other brands. The difference can often be simply the color of the anodizing.

View Woodbum's profile

Woodbum

846 posts in 3302 days


#14 posted 11-18-2016 01:53 PM

Also a vote for the Woodpeckers lift. I have two of them in my tables and they work great. Good family owned American business located in Ohio. Just a tad pricier: $10-$20 over the Jessum in some places, priced the same in others. Just my humble $.02 worth. Good Luck, Work Safely and Have Fun!

-- "Now I'm just another old guy wearing funny clothes"

View shawnn's profile

shawnn

131 posts in 1601 days


#15 posted 11-20-2016 04:33 PM

I use a 3hp Triton router like Rentvent suggested. Mounted in an Incra plate in an Incra table top with a LS positioner. With my Wixey bit height gauge I can adjust to .002” (the gauge increments are .002”). For anyone planning to use a Triton you must ensure the router is oriented properly to access the power, speed & lock mechanisms.

View rick1955's profile

rick1955

264 posts in 1667 days


#16 posted 11-20-2016 05:05 PM

http://www.popularwoodworking.com/projects/aw-extra-8912-shop-made-router-lift
This is a great design…

-- Working smarter with less tools is a true crafts person...

View Madmark2's profile

Madmark2

409 posts in 824 days


#17 posted 11-21-2016 12:15 AM

If you are going to buy a plunge router anyway just get a fixed mount plate and a digital height gauge. Set to .001” using the plunge router knob/wrench. No lift needed & much cheaper / simpler.

M

View 000's profile

000

2859 posts in 1135 days


#18 posted 11-21-2016 12:47 AM



If you are going to buy a plunge router anyway just get a fixed mount plate and a digital height gauge. Set to .001” using the plunge router knob/wrench. No lift needed & much cheaper / simpler.

M

- Madmark2

What kind of digital height gauge? Do you have a picture?

View Madmark2's profile

Madmark2

409 posts in 824 days


#19 posted 11-21-2016 04:03 AM

Wixey:

$60 online.

Wixey.com

M

View woodbutcherbynight's profile

woodbutcherbynight

5825 posts in 2645 days


#20 posted 11-21-2016 04:11 AM

I have been using Router Razier with a baseplate I got at a Woodworking show in 1997. When my router died I had saved the original box and all the extra parts for other routers si I was able to install it on the new different brand router. Only part I needed was the main shaft and when I called them to inquire about buying one they sent it to me free of charge. Maybe not the fanciest unit but it has worked well since 1997 so I have no complaints.

Here is website LINK

-- Live to tell the stories, they sound better that way.

Have your say...

You must be signed in to reply.

DISCLAIMER: Any posts on LJ are posted by individuals acting in their own right and do not necessarily reflect the views of LJ. LJ will not be held liable for the actions of any user.

Latest Projects | Latest Blog Entries | Latest Forum Topics

HomeRefurbers.com