LumberJocks

All Replies on No. 3 vs. No. 4 Smoothing plane?

  • Advertise with us
View 12strings's profile

No. 3 vs. No. 4 Smoothing plane?

by 12strings
posted 03-07-2013 11:41 PM


16 replies so far

View crank49's profile

crank49

3524 posts in 1724 days


#1 posted 03-08-2013 12:26 AM

I don’t have a #3, but always felt like I should have one. Don’t know why.

I think there is a more vocal following of the #4 1/2 as a smoother because it has more width and weight.

Looks like a #3 would be going in the opposite direction but I could see it as useful for small work.

-- Michael :-{| “If you tell a big enough lie and tell it frequently enough, it will be believed.” ― A H

View Don W's profile

Don W

15578 posts in 1321 days


#2 posted 03-08-2013 12:29 AM

I prefer the #4, but I use both a #2 and a #3 for smaller work. I’d suggest starting with a #4. My 604 is the most used plane in my shop.

-- Master hand plane hoarder. - http://timetestedtools.com

View sikrap's profile

sikrap

1065 posts in 2112 days


#3 posted 03-08-2013 03:13 AM

I have both and I use both. I use a 4 for table tops and other large areas and I use a 3 (or 2) for smaller areas like legs on a night stand. If you’re only going to get one, you should definitely try both sizes and see which feels better for you.

-- Dave, Colonie, NY

View LukieB's profile

LukieB

942 posts in 1083 days


#4 posted 03-08-2013 03:24 AM

I have both, and probably reach for my 4 more often. But I love my 3 too.

I agree with Dave,#4 for larger areas, #3 for smaller areas…..or #2, if you’re so fortunate : )

-- Lucas, "Someday woodworks will be my real job, until then, there's this http://www.melbrownfarmsupply.com"

View JayT's profile

JayT

2634 posts in 964 days


#5 posted 03-08-2013 03:37 AM

I definitely prefer my #4, but the #3 has its uses. I do not have large hands, but the little bit of extra room with the #4 makes it more comfortable for me to use.

-- "My concern is not whether God is on our side; my greatest concern is to be on God's side, for God is always right." Abraham Lincoln

View David Kirtley's profile

David Kirtley

1285 posts in 1751 days


#6 posted 03-08-2013 05:02 PM

I am going to go out on a limb and suggest not to even bother with a #3 or smaller and just use a block plane. Same width, same length, same ability or better to close up the mouth. Now if you are collecting, that is a different question. If collecting, I say go for a particular style. Maybe all low knobs because they look much cooler.

-- Woodworking shouldn't cost a fortune: http://lowbudgetwoodworker.blogspot.com/

View bandit571's profile

bandit571

7522 posts in 1436 days


#7 posted 03-08-2013 05:18 PM

Ok, I will buck the trend here. I tend to reach for my #3 sized planes the most. I do have large hands, but there is just something i like about the #3 size.

And really, a 1/4” more in blade width? Not that much is it. The #3 tend to be just a hair less in weight, makes a bit of difference at the end of the day.


Yes, I do have a few of each, just prefer the #3s more. And yes, I also keep a few block planes around.

-- A Planer? I'M the planer, this is what I use

View Cosmicsniper's profile

Cosmicsniper

2199 posts in 1912 days


#8 posted 03-08-2013 05:19 PM

I wear blisters with my 2 and 3 if I’m not careful. Not so with my 4. I still use them all though.

-- jay, www.allaboutastro.com

View bondogaposis's profile

bondogaposis

2760 posts in 1104 days


#9 posted 03-08-2013 06:53 PM

I have a 3 and 4 1/2. I probably grab the 3 more often even though it’s a bit tight on my hands. I hang my index finger around the upper blade rather on the grip and it fits better. I’m not sure why I like it better, maybe because it is lighter.

-- Bondo Gaposis

View Mosquito's profile

Mosquito

5191 posts in 1045 days


#10 posted 03-08-2013 07:02 PM

I’ve got a #2, #3, and #4. Between those 3 I use the #3 the most. I really like using it for chamfers, rounding corners, and smaller raised panels. I typically use my #5 1/2 as my main face-smooting plane, just because I like the size, weight, and blade width.

Similar to what Bondo does, I have my pointer finger extended along side the blade, and sometimes have my pinky extended on the bed of the plane (but still inside the sole). That feels relatively comfortable to me, and in some cases makes me feel like I have better stability of the plane in my hand

-- Mos - Twin Cities, MN -- Stanley #45 Evangelist - www.youtube.com/MosquitoMods

View Ron Harper's profile

Ron Harper

133 posts in 670 days


#11 posted 03-09-2013 12:21 AM

I use two 4s. One is my utility plane and I use it for almost everything ala Paul Sellers . I keep the other one set fot the very tiniest of shavings for final polishing. I do have an Old Street Tools smoother that is awesome. It is 2 sized. I use it for tough grain.

-- Ron in Kokomo

View Benvolio's profile

Benvolio

135 posts in 684 days


#12 posted 03-09-2013 11:57 AM

I find it’s easier to get finer cuts with a number three as it has a smaller reference surface… but that’s by such a miniscule amount as to barely bother mentioning.

also because the blade isn’t as wide it’s quicker to sharpen.

Other than that, I think if Al Qaida came to power tomorrow and outlawed the number 3 – I think I could make it comfortably enough without being stoned to death. There’s nothing a number 3 does that a 4 doesn’t.

So if you’re in the market for buying both, I’d say just buy a number 4 and put that money towards one GOOD plane, rather than two pretty okay planes.

-- Ben, England.

View BigRedKnothead's profile

BigRedKnothead

5840 posts in 735 days


#13 posted 03-10-2013 02:32 PM

I guess the thing to take from this is: preference. I have both. Use them both. Try em both if your able. You can get good ol 3’s and 4’s for 30-40 bucks all day.
I made a custom tote for my no 3 because my large hands didn’t fit. Technically the tote is the same size, but stuffs a little more packed in. I have to put my in index finger extended on the side of the frog/iron on any of the smaller planes.
btw. I have a veritas no 4, and I like my 604 better.

-- Red-- "At the end of the day, try and make it beautiful....because the world is full of ugly." Konrad Sauer

View pmayer's profile

pmayer

609 posts in 1818 days


#14 posted 03-10-2013 10:20 PM

I use a 4 more than a 3, but I like the 3 a lot. I would start with a #4, and then add a #3 within an hour or two at most. :)

-- PaulMayer, http://www.vernswoodgoods.com

View HorizontalMike's profile

HorizontalMike

6968 posts in 1667 days


#15 posted 03-11-2013 01:08 AM

I use the #6 more often than the #4. IMO, #4 is too short. I recently acquired 4 #5s and will let you know…

-- HorizontalMike -- "Woodpeckers understand..."

View 12strings's profile

12strings

433 posts in 1137 days


#16 posted 03-11-2013 01:46 PM

I have a Stanley #5, but no real smoothing plane…so my current method for an even finish is to do as much as I can with the #5, then break out the Random Orbital sander on a fine grit…especially if I’m staining…I never get good stain reception right off the handplanes.

-- I'm strictly hand-tool only...unless the power tool is faster and easier!

Have your say...

You must be signed in to reply.

DISCLAIMER: Any posts on LJ are posted by individuals acting in their own right and do not necessarily reflect the views of LJ. LJ will not be held liable for the actions of any user.

Latest Projects | Latest Blog Entries | Latest Forum Topics

HomeRefurbers.com

Latest Projects | Latest Blog Entries | Latest Forum Topics

GardenTenders.com :: gardening showcase