LumberJocks

All Replies on Orbital or 1/4 sheet sander?

  • Advertise with us
View BigJerryWayne's profile

Orbital or 1/4 sheet sander?

by BigJerryWayne
posted 574 days ago


17 replies so far

View pintodeluxe's profile

pintodeluxe

3273 posts in 1415 days


#1 posted 574 days ago

Random orbit sander is the only one I use. My 1/4 sheet buzz sander just sits in the cabinet. The old 1/4 sheet sanders vibrate your hand numb very quickly, and tend to get squirrely. The new breed of ROS’s, especially those with variable speed are a vast improvement. They are much easier to handle, and the resulting finish is great.
I like the Bosch and Dewalt 5” sanders. I use them connected to a shop vac.
Good luck.

-- Willie, Washington "If You Choose Not To Decide, You Still Have Made a Choice" - Rush

View Mark Smith's profile

Mark Smith

491 posts in 642 days


#2 posted 574 days ago

The orbital sanders are obviously round because they orbit. That means you can’t get into corners with them if you have that need. Like Willie, I only use an orbital sander because it just does so much better of a job. Someplace around my shop that I would have to search for, I have one of those pointy nose vibration sanders that I can dig out in the event I need to get into corners. What I would normally do is finish sand before assembly to avoid having to sand in corners. If you are only buying one, my suggestion is the orbital.

-- Mark Smith, Tracy, CA., http://www.markscustomwoodcrafts.com

View GT350's profile

GT350

265 posts in 584 days


#3 posted 573 days ago

I prefer my 5” orbital sander. Keep in mind that it won’t get into corners but you can always hand sand those spots. Mine uses hook and loop sandpaper and it doesn’t tear like quarter sheet paper does and it is easier to change paper than the quarter sheet sander.

View woodworkerscott's profile

woodworkerscott

357 posts in 1416 days


#4 posted 573 days ago

A fourth vote on the ROS. There is no choice, as far as I am concerned. The advantages of the ROS over the 1/4 sheet sander are numerous. Plus, the 1/4 sheet sander is gonna leave those pesky little swirl marks (pig tails) that like to stay hidden until the finish is applied. Plus you are limited in sanding in regards to grain direction. With a ROS you can sand any direction and when you have grain meeting from different directions (mitered corners, perpendicular, etc) there is no worries of scratching the grains.
So go with the ROS….you’ll love it.

-- " 'woodworker'.....it's a good word, an honest word." - Sam Maloof

View BentheViking's profile

BentheViking

1746 posts in 1166 days


#5 posted 573 days ago

+1 for ROS. My 1/4 sheet always had problems holding onto the sandpaper and id end up scrubbing with it so it was basically a powered hand sander. Not even sure if I have it any more. Once I went ROS I never looked back and you won’t either.

I get it about the corners but 1/4 sheets don’t get in completely either. I have the sanding attatchment for my osciliating multi tool if I need to or I can always do it by hand.

-- It's made of wood. Real sturdy.--Chubbs Peterson

View Howie's profile

Howie

2656 posts in 1525 days


#6 posted 573 days ago

I have a Ridgid and a PC orbital. My go to is the PC .

-- Life is good.

View NiteWalker's profile

NiteWalker

2709 posts in 1179 days


#7 posted 573 days ago

I have and use both, as both have their place.
For flat pieces I use a ROS (dewalt D26456) and on areas with curves and for my small boxes I use a porter cable 330.

-- He who dies with the most tools... dies with the emptiest wallet.

View gfadvm's profile

gfadvm

10593 posts in 1292 days


#8 posted 573 days ago

I bought the DeWalt set that had both sanders a long time ago. The quarter sheet sander gets very little use but is nice for sanding curves where the ROS wants to bridge the curve and dig a groove.

-- " I'll try to be nicer, if you'll try to be smarter" gfadvm

View robjeffking's profile

robjeffking

26 posts in 708 days


#9 posted 573 days ago

The ros is the best for finishing and swirling out machine marks but the sheet sanders work the best on edge sanding
I also find the sheet sanders works best at holding a heavier paper not to mention you can clamp in non-velcro paper
you may have laying around . Go with the ROS first and look for a model with a sealed on/off switch my first ros sander’s switch was unprotected and failed in less than a year.

View Dusty56's profile

Dusty56

11639 posts in 2290 days


#10 posted 573 days ago

Go for the ROS first and if you ever need a superb 1/4 sheet , you can’t go wrong with this model : )
http://www.amazon.com/Porter-Cable-330-Speed-Bloc-Sheet-Sander/dp/B0000222Y9

-- I'm absolutely positive that I couldn't be more uncertain!

View Tedster's profile

Tedster

2269 posts in 813 days


#11 posted 573 days ago

I haven’t touched my 1/4 sheet sander at all since I acquired my Bosch oscillating tool.

http://www.amazon.com/Bosch-MX25EC-21-2-5-Amp-Multi-X-Oscillating/dp/B004HKCGQK/ref=sr_1_1?s=hi&ie=UTF8&qid=1357101659&sr=1-1&keywords=bosch+oscillating

It gets into corners and does a dozen other chores as well. For most sanding I use a Dewalt orbital sander.

-- I support the 28th Amendment. http://www.wolf-pac.com/28th

View beech's profile

beech

7 posts in 635 days


#12 posted 572 days ago

Happy New Year!

Love the holidays

Got this great Dynabrade

and a lot of PSA discs to go with it.

Super happy my love found this on the web

View JoeinGa's profile

JoeinGa

3103 posts in 609 days


#13 posted 571 days ago

I have a Makita 1/4 sheet that I bought in 1989. I usedta think it was the best thing since sliced bread. Well except for those dam pesky paper clamps that are such a pain! I bought a ROS (Dewalt) about 5 years ago and havent touched the Makita since then. In fact I bought another about 3 months ago and havent even taken it out of the box yet.
So now you know which way I vote

-- Perform A Random Act Of Kindness Today ... Pay It Forward

View BigJerryWayne's profile

BigJerryWayne

133 posts in 705 days


#14 posted 570 days ago

Thank you for all the input. I am one to look at reviews on things before I buy, and I see lots of positive reviews on the Bosch ROS20VSK. I have a Craftsman C3 pad (mouse) sander for corners. I was at Lowe’s the other day and gave the sanders a good looking over. I think I can hear the Bosch telling me to come get it now, and will probably go get it before the day’s end. I can go to Lowe’s and just walk around and look for at least a couple of hours at a time, and do that quite often. It keeps me out of the beer joints and pool halls, as my dad used to say. lol

-- An oak tree is just a nut that stood it's ground.

View gfadvm's profile

gfadvm

10593 posts in 1292 days


#15 posted 570 days ago

beech- Yer gonna love that sander! I don’t use that PSA paper though. I use Abranet for the speed, longevity, and great dust collection. Enjoy!

-- " I'll try to be nicer, if you'll try to be smarter" gfadvm

View crank49's profile

crank49

3338 posts in 1573 days


#16 posted 570 days ago

I bought a Ridgid 5” ROS and was very impressed that it can remove material as fast as a belt sander, and then finish better than a 1/4 sheet finish sander just by adjusting the speed and paper. The dust collection is great as well because of the holes in the disk.

Then, at some point, I was buying a Dewalt jig saw (saber saw) and they had a free 1/4 sheet sander in the kit. So I now have both, and can feel comfortable in saying the 1/4 sheet palm sander is worth every penney I paid for it.

-- Michael :-{| “If you tell a big enough lie and tell it frequently enough, it will be believed.” ― A H

View robert triplett's profile

robert triplett

1481 posts in 1707 days


#17 posted 567 days ago

Well, I certainly feel like the odd man out here. I use a Porter Cable Speed Bloc exclusively. I had a black and Decker and then a DeWalt ROS and gave them away. I did not like the finish. Maybe it was the paper. I use Norton 3X and like how it works.

-- Robert, so much inspiration here, and so little time!

Have your say...

You must be signed in to reply.

DISCLAIMER: Any posts on LJ are posted by individuals acting in their own right and do not necessarily reflect the views of LJ. LJ will not be held liable for the actions of any user.

Latest Projects | Latest Blog Entries | Latest Forum Topics

HomeRefurbers.com

Latest Projects | Latest Blog Entries | Latest Forum Topics

GardenTenders.com :: gardening showcase