LumberJocks

All Replies on Dewalt 735 Planer set up question

  • Advertise with us
View bbasiaga's profile

Dewalt 735 Planer set up question

by bbasiaga
posted 12-26-2012 02:13 AM


19 replies so far

View RVroman's profile

RVroman

163 posts in 746 days


#1 posted 12-26-2012 02:30 AM

I have had this planer for years and I have never gotten it to be “snipe free”. What you are getting is about what I have been getting, and maybe a bit better

-- Robert --- making toothpicks one 3x3x12 blank at a time!

View joeyinsouthaustin's profile

joeyinsouthaustin

1285 posts in 795 days


#2 posted 12-26-2012 02:34 AM

I just got my 3rd 735. It is a great machine. There is no such thing as a no snipe machine in my experience, but there is a no snipe technique with this machine. I run mine with no extensions, and lift the board as it goes in and comes out. This pinches it down to the table. It would say it would work if you set your tables slightly above “flat” with the table and let the in and out feed roller flatten the board to the table, producing the same effect. I have gotten VERY clean boards off this machine with about %10 upforce over the weight of the board.

P.S. It is my third because I keep one for portable, and one in the shop. I wore my first out finally after 7 years of industrial use. (snapped the out feed roller) It is currently being repaired and I will have three running.

-- Who is John Galt?

View juniorjock's profile

juniorjock

1930 posts in 2488 days


#3 posted 12-26-2012 02:37 AM

I have never seen this planer reviewed as “no” snipe…... You’ll get snipe once in a while. You can experiment with the tables by raising the ends slightly. I don’t have the tables so I just lift up a little on the end of the infeed and outfeed. I usually cut the boards a little long in case I have to trim the ends off. Good luck.

View ShaneA's profile (online now)

ShaneA

5411 posts in 1320 days


#4 posted 12-26-2012 02:38 AM

Agree with the others. Make sure the boards are a few inches longer than you need, then cut the snipe away, is what I do.

View PurpLev's profile

PurpLev

8476 posts in 2371 days


#5 posted 12-26-2012 02:54 AM

I get a slight snipe on mine from time to time, it seemed that it happens more often with shorter boards then with longer ones.

-- ㊍ When in doubt - There is no doubt - Go the safer route.

View jmartel's profile (online now)

jmartel

2576 posts in 872 days


#6 posted 12-26-2012 04:33 AM

Adjust your in/outfeed tables so they are slightly higher than the bed, no more than 1/16”. That should help. Also, hold the rear of the board up when you’re feeding it in. There’s no way to completely prevent it, but mine doesn’t produce much snipe at all after doing that. Can’t see it, and you can only barely feel it on a few of the boards that go through.

-- End grain is like a belly button. Yes, I know you have one. No, I don't want to see it.

View Matt Przybylski's profile

Matt Przybylski

467 posts in 1100 days


#7 posted 12-26-2012 04:58 AM

The other way to reduce snipe that I use with my 735 is I feed the next board I’m using before the first one finishes, about 2/3 of the way through. That way the rollers are always engaged. If you’re on your last board use a test piece to finish with so that if there is any snipe it’ll happen on the test piece and not your work piece. I love this planer, by the way :)

-- Matt, Illinois, http://www.reintroducing.com

View pintodeluxe's profile

pintodeluxe

3514 posts in 1535 days


#8 posted 12-26-2012 05:34 AM

There is a way to adjust the tables to avoid any snipe. Raise the cutterhead all the way up. Set a straightedge on the planer bed. Adjust the far ends of the infeed and outfeed tables slightly upwards. Raise them until you can just slip a dime under the middle of the straightedge.
This will solve snipe for boards up to 6’ long. Any longer than that, and you will need some outfeed support.
It is a great planer, I think you will be pleased.

Good luck.

-- Willie, Washington "If You Choose Not To Decide, You Still Have Made a Choice" - Rush

View exelectrician's profile

exelectrician

1714 posts in 1149 days


#9 posted 12-26-2012 06:42 AM

My DeWalt took my woodworking to the next level. Out of the box I have not experienced any snipe from day one, am I the lucky one? I have swapped my blades over and now need a new set. I mainly use my DeWalt on hard maple and oak.

-- Love thy neighbour as thyself

View Howie's profile

Howie

2656 posts in 1645 days


#10 posted 12-26-2012 11:36 AM

I’m with exeletrician, I rarely get any snipe. My tables are set flat and then let the board run out on an auxillary roller stand before picking it up.
I always use a longer board and then cut the ends square after planning.

-- Life is good.

View bbasiaga's profile

bbasiaga

112 posts in 717 days


#11 posted 12-26-2012 02:14 PM

Thanks guys. The board was using was only about 18” long so that may not have helped. I will adjust the tables as suggested above and give it another go. I would say that what snipe i did get was hardly noticeable. I’m not even sure it would require any sanding. But given my lack of experience setting this stuff up I thought I’d ask for ways to make it better.

Thanks,
Brian

-- Part of engineering is to know when to put your calculator down and pick up your tools.

View JesseTutt's profile

JesseTutt

811 posts in 833 days


#12 posted 12-26-2012 02:26 PM

My Delta snipes each end (infeed and outfeed end). If the width is less than my jointer I plane the board to a little thicker than I want and then finalize it on the jointer using very thin passes (< 164). If the board is wider than the jointer I cut it long and cut off the snip.

-- Jesse, Saint Louis, Missouri

View MedicKen's profile

MedicKen

1602 posts in 2184 days


#13 posted 12-26-2012 02:29 PM

Another help may be to set up a roller stand to help support longer boards as they enter and exit the planer. I would sometimes get some snipe from my 734 if the ends were left unsupported. I used roller stands set about 1/4” higher than the outfeed on boards over 4’ in length. I helped a lot in eliminating snipe.

-- My job is to give my kids things to discuss with their therapist....medic20447@gmail.com

View Jim Finn's profile

Jim Finn

1733 posts in 1644 days


#14 posted 12-26-2012 02:33 PM

I have this planer also and I just raised up the ends of the in-feed and out-feed tables a bit to give the board the upward pressure mentioned above. Works well for me.

-- In God We Trust

View joeyinsouthaustin's profile

joeyinsouthaustin

1285 posts in 795 days


#15 posted 12-26-2012 03:03 PM

These dwalt 735 threads always take off. Here are some other things to watch for on this machine that I have experienced and that have been mentioned in the past.
1: The cowling wears at the back. This happens at about 50,000 Board Feet. It can quickly fill the case with chips and cause damage. The part is cheap and easy to replace, so watch for this and fix right away. 2. Do not use with in-adequate dust collection. Our 5hp shop vac was not enough and chips would back up and wear the cowling faster. It is that the on board chip vac moves a lot of air and that causes the prob. If it is the only option, rigg the nozzle to sit 1/2” back to create an air release. It will get most the chips and fine dust w/o backing up, or create a pressure release somewhere else in the system. It works great with a 1.5 hp dust collector. It has to do with the airflow, not suction or power. 3. It is loud. 4. Two parts are subject to fatigue. The cogs on the in and out feed roller drive, they don’t wear, they crack and the chain starts slipping. (Cheap and easy to replace) and the out feed roller (Cheepish, not easy to replace)(happens like a clock at about 500,000 BF) Both can be mitigated by only running half of what the depth gauge recommends. And last. power. It will overheat and fail if it is run long term on inadequate power. Run it of of direct power, or read carefully the specs needed to run it off of an extension cord. I have run these machines in an industrial setting and they have earned my respect. The factory max repair is $299. With an average life of 10 years before big repairs are needed, (near continuous use in an industrial setting) I can easily get a lifetime of use out of them before it gets more expensive than an industrial machine. Width is the only thing that has pushed me to buy bigger and I will continue to run this next to 18” I just bought.

-- Who is John Galt?

View joeyinsouthaustin's profile

joeyinsouthaustin

1285 posts in 795 days


#16 posted 12-26-2012 03:46 PM

Oh, and one more thing. If you really want the machine to be the next level. Byrd does make a shelix head for the 735!!! only cost’s about as much as the machine itself, but just imagine.

-- Who is John Galt?

View Romaxxster's profile

Romaxxster

2 posts in 700 days


#17 posted 12-26-2012 04:24 PM

Here’s a short video I found on YouTube. The guy has several tutorial videos and some pretty clever tips & tricks about lots of woodworking subject. In this video, he explains “why” planers & jointers produce snipe. http://www.youtube.com/watch?v=mHfjSatKITQ&list=UUwQll2Vb7ndCw--Y4lVORYA

I have the 735 as well & even after knowing (or thinking I know) how to eliminate snipe, I still get it, slightly. At least now I understand why I get it. If nothing else, I sleep good again.

-- Dan - Why people say "Excuse my French" in English, is Greek to me!

View MedicKen's profile

MedicKen

1602 posts in 2184 days


#18 posted 12-26-2012 04:50 PM

You could always do this

-- My job is to give my kids things to discuss with their therapist....medic20447@gmail.com

View joeyinsouthaustin's profile

joeyinsouthaustin

1285 posts in 795 days


#19 posted 12-26-2012 05:02 PM

One thing to think about with the Romaxxster and Medicken posts, great knowledge to apply, is that the table on the 735 IS compress-able. The double stick that they use to apply the chrome liner does compress. So if you lift too much you can get the opposite snipe. This is why the two board method works, it keeps everything compressed, and why the MedicKen soluction works very well.

-- Who is John Galt?

Have your say...

You must be signed in to reply.

DISCLAIMER: Any posts on LJ are posted by individuals acting in their own right and do not necessarily reflect the views of LJ. LJ will not be held liable for the actions of any user.

Latest Projects | Latest Blog Entries | Latest Forum Topics

HomeRefurbers.com

Latest Projects | Latest Blog Entries | Latest Forum Topics

GardenTenders.com :: gardening showcase