LumberJocks

All Replies on Advice Sought: Squaring my POS sliding mitre saw

  • Advertise with us
View Milo's profile

Advice Sought: Squaring my POS sliding mitre saw

by Milo
posted 762 days ago


18 replies so far

View Bill White's profile

Bill White

3404 posts in 2587 days


#1 posted 762 days ago

Uhhhh? POS? Why didja buy it?
After that blast….Good blade (muy importante), table adjust ( as in stops), a good square for set-up ( I use a drafting square for most). Even some crappy MSs can be made to work well with proper set-up.
Are the bearings shot? Lot’s of “wiggle” at full extension of the arm?
Bill (Who’s blocked by Poopiecat for some unknown reason).

-- bill@magraphics.us

View Joe Lyddon's profile

Joe Lyddon

7676 posts in 2679 days


#2 posted 762 days ago

It obviously does not SLIDE in a straight line.

Good luck!

-- Have Fun! Joe Lyddon - Alta Loma, CA USA - Home: http://www.WoodworkStuff.net ... My Small Gallery: http://www.ncwoodworker.net/pp/showgallery.php?ppuser=1389&cat=500"

View jim C's profile

jim C

1452 posts in 1725 days


#3 posted 762 days ago

Loosen your back rail and square it to the blade.

-- When I was a boy, I was told "anyone can be President", now I'm beginning to believe it!

View Milo's profile

Milo

851 posts in 1946 days


#4 posted 761 days ago

Bill,

You’ve never bought spur of the moment and regretted it later?

;)

-- Beer, Beer, Thank God for Beer. It's my way of keeping my mind fresh and clear...

View devann's profile

devann

1735 posts in 1319 days


#5 posted 761 days ago

Maybe this will help you Milo.

To check that your miter saw is cutting true, take a board that is near the cutting capacity of the saw in width, and say 18”+ long. With the saw set to 0° cutting near the center of the board make a cross cut. Now flip one of the pieces you just cut over, placing the side that was closest to you to the fence. Butt the cut together and check for a gap. If there is no gap your saw is cutting true. If there is a gap, adjust saw until a tight joint is achieved. Same technique applies for the bevel settings of a saw.

-- Darrell, making more sawdust than I know what to do with

View jim C's profile

jim C

1452 posts in 1725 days


#6 posted 761 days ago

Again, look at post 3. IMO, Thats all thats needed to adjust.
Lay a square against the teeth of the blade and move the fence until it is aligned with the perpendicular side of the square.

-- When I was a boy, I was told "anyone can be President", now I'm beginning to believe it!

View cutworm's profile

cutworm

1064 posts in 1420 days


#7 posted 761 days ago

I adjust mine like Darrell and Jim. I loosen one end of the fence and leave on end tight. Tap the loose end with a hammer. And draw a line along the fence on the base to see if it’s moving and how much.

-- Steve - "Never Give Up"

View Milo's profile

Milo

851 posts in 1946 days


#8 posted 758 days ago

I’ll see if I can do that Jim. Took me a while to figure out what your were telling me, then, light bulb!.

Hope that rail doesn’t move with the fence though… :(

-- Beer, Beer, Thank God for Beer. It's my way of keeping my mind fresh and clear...

View jim C's profile

jim C

1452 posts in 1725 days


#9 posted 758 days ago

What rail?
There’s a stationary fence that back up the wood to be cut.you should be able to loosen the screws and square perpendicular to the blade.

-- When I was a boy, I was told "anyone can be President", now I'm beginning to believe it!

View Howie's profile

Howie

2656 posts in 1550 days


#10 posted 758 days ago

Take a day off from woodworking. Go fishing. Use saw for boat anchor. “Lose” anchor. Find new saw.

-- Life is good.

View Sawkerf's profile

Sawkerf

1730 posts in 1695 days


#11 posted 758 days ago

Can’t tell what brand it is, but that back “rail” looks like the one on my Makita SCMS. Mine has two bolts (one at each end) that allow it to be squared to the blade.

Set the saw to 0* and lock it in the down position. Use a square (a speed square should work fine) to align the back “rail” to the blade and tighten the bolts. Piece of cake and shouldn’t take more than a couple of minutes.

-- Adversity doesn't build character...................it reveals it.

View Bill White's profile

Bill White

3404 posts in 2587 days


#12 posted 758 days ago

“You’ve never bought spur of the moment and regretted it later?”

Yep! Though I didn’t “buy” my first wife.

I also bought some MinWax stuff, but that’s another story.

Bill

-- bill@magraphics.us

View Milo's profile

Milo

851 posts in 1946 days


#13 posted 757 days ago

This is a true POS guys. The back fence does NOT move independent of the table. Yeah!

But see that knob in the first picture, on the right, behind the fence? It locks the table in place, even the 2 degrees I need to make it square. yeah! I think I found my solution. Now to get some scrap and test until I get it right.

THANKS GANG! You guys are the best.

Milo

p.s. Howie, strongly considering your ideas…. ;)

-- Beer, Beer, Thank God for Beer. It's my way of keeping my mind fresh and clear...

View Alexandre's profile

Alexandre

1417 posts in 818 days


#14 posted 757 days ago

What does POS stand for?
Sorry, I don’t know what it means :P

-- My terrible signature...

View Milo's profile

Milo

851 posts in 1946 days


#15 posted 757 days ago

Piece

Of

S#@$.....

:)

-- Beer, Beer, Thank God for Beer. It's my way of keeping my mind fresh and clear...

View lumberjoe's profile

lumberjoe

2829 posts in 875 days


#16 posted 757 days ago

1. Sell it on craigslist for twice what you paid for it
2. Purchase the frosty libations of your choosing with the profit
3. Enjoy said libations
4. When the effects of said libations wear off, use your table saw to make square cuts

-- www.etsy.com/shop/KandJWoodCrafts

View Alexandre's profile

Alexandre

1417 posts in 818 days


#17 posted 757 days ago

And buy a Japenese chisel with the money you get from your POS.

-- My terrible signature...

View Milo's profile

Milo

851 posts in 1946 days


#18 posted 756 days ago

HA! Thanks everyone!

-- Beer, Beer, Thank God for Beer. It's my way of keeping my mind fresh and clear...

Have your say...

You must be signed in to reply.

DISCLAIMER: Any posts on LJ are posted by individuals acting in their own right and do not necessarily reflect the views of LJ. LJ will not be held liable for the actions of any user.

Latest Projects | Latest Blog Entries | Latest Forum Topics

HomeRefurbers.com

Latest Projects | Latest Blog Entries | Latest Forum Topics

GardenTenders.com :: gardening showcase