LumberJocks

All Replies on I tried but I could not say "NO"

  • Advertise with us
View b2rtch's profile

I tried but I could not say "NO"

by b2rtch
posted 12-18-2011 02:42 PM


19 replies so far

View helluvawreck's profile

helluvawreck

29192 posts in 2706 days


#1 posted 12-18-2011 02:50 PM

Congratulations. For $75 most any woodworker would like to have it and what you got with it.

helluvawreck
http://woodworkingexpo.wordpress.com

-- If a man does not keep pace with his companions, perhaps it is because he hears a different drummer. Let him step to the music which he hears, however measured or far away. Henry David Thoreau

View canadianchips's profile

canadianchips

2600 posts in 2836 days


#2 posted 12-18-2011 02:53 PM

Your wife is a keeper …...
Good find on the shaper, I am always looking as well, ONE day I will.
Go online, you can buy NEW shaper knifes from a company called “Elite” based out of Quebec Canada. I am certain there are places in the USA as well. For larger jobs a shaper is far superior to a router EVERYTIME. (Quieter too)

-- "My mission in life - make everyone smile !"

View b2rtch's profile

b2rtch

4847 posts in 2887 days


#3 posted 12-18-2011 02:55 PM

’ Your wife is a keeper ……” I KNOW THAT.( that’s why she still is my wife)

-- Bert

View 404 - Not Found's profile

404 - Not Found

2544 posts in 2808 days


#4 posted 12-18-2011 03:16 PM

75 bucks! wow, what a result!

View muleskinner's profile

muleskinner

896 posts in 2276 days


#5 posted 12-18-2011 03:19 PM

I assume the ‘mistake’ was driving away in the first place and having to consume more gas driving back. That looks like a well spent 75 bucks.

-- Visualize whirled peas

View b2rtch's profile

b2rtch

4847 posts in 2887 days


#6 posted 12-18-2011 03:29 PM

“I assume the ‘mistake’ was driving away in the first place and having to consume more gas driving back.” it was just to the driveway across the street

-- Bert

View Don W's profile

Don W

18523 posts in 2407 days


#7 posted 12-18-2011 04:12 PM

I have that exact same shaper. I bought it new probably 25 years ago (guessing here but its close). I was doing it for a living at the time, so it got a lot of use. I replaced the 1 hp motor with a 3hp. I honestly can not remember if the 1 hp burnt out or I just wanted more power.

When I moved out of my shop, it sat for a few years. When I built my new shop I was unsure whether I would set it up. I had taken the motor off it for something else, but found myself with an extra 3 hp motor, so its back in service again.

It’s a little loud, and I need to figure out a better dust collection system. Shapers seem to send dust though out the shop.

Either way, you’ve got a great deal and I think you’re going to be glad you bought it.

I called HF a while back. This is what the tech told me about a router bit adapter. I never ordered them because I’m not sure I’d want to run router bits in the shaper.
—————————————————-
We have no way to say for sure that you would be able to use the parts
from the 95668 on the 138 as item 138 is discontinued and we do not have
any that we could check. If you would like to order the parts you are
welcome to do so and if they do not work you can send them back for a
refund as long as you call within 30days of receiving the parts. If you
would like to order those parts please call 1-800-444-3353 or
1-800-423-2567 and request the following item numbers. #10210.0zza 102 95668 COLLET NUT back ordered until
11/27/09 $12.96 #10211.0zza 103 95668 1/4 COLLET back ordered until
12/28/09 $9.00 #10212.0zza 104 95668 1/2 COLLET back ordered until
11/27/09 $9.00
—————————————————————

-- http://timetestedtools.net - Collecting is an investment in the past, and the future.

View CharlieM1958's profile

CharlieM1958

16272 posts in 4057 days


#8 posted 12-18-2011 04:41 PM

Looks like a deal to me!

-- Charlie M. "Woodworking - patience = firewood"

View b2rtch's profile

b2rtch

4847 posts in 2887 days


#9 posted 12-18-2011 04:44 PM

DW, it is interesting and informative to check different part books as on the Fox shop they explain that you need to space the table up for router bits as with the collets the bits would be way too high above the table.

http://pics.woodstockint.com/manuals/w1701_m.pdf

I am about sure that the parts would fit just fine.
Another ting to consider is that the shaper rotate at about 1/3 to 1/2 the speed of a router, that should be fine for large cutter heads but for small one that could be too slow.

Installing a different (read more HP) motor should allow to either install a motor which spins faster or to install a larger driving pulley to increase the bits RPMs and then install a variable speed controller ( I already have one that I do not use)

Hot roding my tools is my favorite hobby, more than in fact using them.

-- Bert

View b2rtch's profile

b2rtch

4847 posts in 2887 days


#10 posted 12-18-2011 05:02 PM

Thank you Charlie (I hope that you mean to say a “good” deal)_

-- Bert

View Don W's profile

Don W

18523 posts in 2407 days


#11 posted 12-18-2011 05:02 PM

the other thing to note about this shaper is the table is a bit small. I used it a lot for raised panel doors, sometime big doors. With longer stock an infeed and outfeed table is a must, even for the stiles.

I found the 1 hp motor didn’t like raising panels in hardwood. It took to many passes for me, thus the 3 hp upgrade.

Today, doing this as a hobby, I wouldn’t buy a shaper (unless I got a deal like yours) but I have it, it works well, so I’ll certainly use it.

I’m working on a panel raiding hand plane. I’ll use that (assuming I make it work well) for a panel or two, but when you’re looking at a dozen raised panels, this little sweetheart shines.

-- http://timetestedtools.net - Collecting is an investment in the past, and the future.

View Les 's profile

Les

201 posts in 2530 days


#12 posted 12-18-2011 05:37 PM

Lucky dog, I want a shaper, but I keep putting it off. I did the same thing with a drum sander, but I found a 26” woodmaster for 750. I guess I will wait a while longer:)

-- Stay busy....Stay young

View b2rtch's profile

b2rtch

4847 posts in 2887 days


#13 posted 12-18-2011 05:38 PM

“Stay busy….Stay young” I believe this is true

-- Bert

View Bluepine38's profile

Bluepine38

3372 posts in 2924 days


#14 posted 12-18-2011 07:40 PM

You really got a good deal on that shaper, I got one I paid $50 for, but it did not have the extra knives and
needed a lot more TLC to just get it to run. It is a 1953 King-Seeley, and I spent way more time rebuilding
it than I have operating it since it was finished. Don W’s advise is right on, hope you have lots of fun with
this new toy.

-- As ever, Gus-the 79 yr young apprentice carpenter

View Loren's profile

Loren

9633 posts in 3487 days


#15 posted 12-18-2011 08:04 PM

Those cutters you got with it are worth significantly more than
you paid for the whole outfit.

View a1Jim's profile

a1Jim

116592 posts in 3416 days


#16 posted 12-18-2011 08:08 PM

A super buy Bert,congrats.

-- http://artisticwoodstudio.com Custom furniture

View TCCcabinetmaker's profile

TCCcabinetmaker

932 posts in 2194 days


#17 posted 12-18-2011 08:18 PM

Just one of those shaper heads (they are not bits) could have cost 75$

The spindels on shapers often can be changed out, There was an old powermatic that I could swap out spindels in about 2 minutes to another size. It was a huge pain, because really all we needed was the shim style washers so that I could use the larger heads on the smaller spindel…. I am not that familiar with this shaper, but it’s kind of a design thing that they have a spindel driven by a belt coming from a motor. They are quite simple machines if you think about it.

-- The mark of a good carpenter is not how few mistakes he makes, but rather how well he fixes them.

View SnowyRiver's profile

SnowyRiver

51453 posts in 3319 days


#18 posted 12-19-2011 04:13 AM

Congrats…great get!

-- Wayne - Plymouth MN

View ShaneA's profile

ShaneA

6865 posts in 2437 days


#19 posted 12-19-2011 04:30 AM

Nice score, great price. Congrats.

Have your say...

You must be signed in to reply.

DISCLAIMER: Any posts on LJ are posted by individuals acting in their own right and do not necessarily reflect the views of LJ. LJ will not be held liable for the actions of any user.

Latest Projects | Latest Blog Entries | Latest Forum Topics

HomeRefurbers.com