LumberJocks Woodworking Forum banner

Shop insulation

Tags
question
3K views 20 replies 17 participants last post by  Momcanfixit 
#1 · (Edited by Moderator)
Probably a much discussed topic so I will apologize in advance. Much as I would love to have a temperature and humidity controlled workshop, I work out of a two car garage with no air-conditioning or heating. With winter approaching I am thinking once again about practical and realistic ways to keep my shop comfortable enough to work in without going to significant expense, or moving to Florida. I should add that I live in Ohio where the summers are hot and humid and the winters are bloody cold.

My first consideration is the garage doors which are made of sheet metal with a thin lining of mdf, and with single pained glass windows at the top of each door. I can probably get double-glazed units to replace the existing windows, and add insulation to the door panels but will this really provide any significant benefits? The doors are surrounded by thin weather stripping so I am not convinced that I will be able to prevent drafts or heat loss around the doors. The walls and ceiling of my garage are all fully insulated.

I can always add a heater to the garage but as I would not have it running 24 X 7 and therefore maintaining a constant temperature, I would be concerned about condensation immediately forming on the metal surfaces of my machines whenever I fired it up. I do use CRC on all my cast iron surfaces but it does not prevent moisture from forming of course.

Just curious about the experiences of others living in similar climes.
 
See less See more
#2 ·
Those roll up doors on garages make a garage a really tough place to keep climate controlled. They leak like sieves and don't provide any real thermal barrier. If you are using the garage as a dedicated space for woodworking, you could do what I did and replace this kind of door with a skookum pair of barn style doors that are fully insulated and seal the opening well. I use these doors when necessary to get big stuff in and out, otherwise they remain shut and I use the passage door. Not perfect but a huge improvement climate wise.

I am surprised your garage has insulated outer walls and ceiling. Mine did not.
 
#4 ·
I covered my uninsulated overhead door with pieces of foam insulation board and duct taped the seams. I then applied that weatherstripping around the outside frame. It looks a little "ghetto" but made a BIG difference (and it still looks fine from the outside).
 
#6 ·
If you have the plain steel (or aluminum) doors, you can get the insulating pads put in behind the panels. That helps a lot. What does your shop look like? Are there open rafters that you can add insulation to? I live in southern California, and I added reflective barrier insulation to the ceiling in as many areas as I could, and it makes a great difference.
 
#8 ·
Like gfadvm said add some ridged insulation to the door the thicker the better,you can even cover the windows by pressure fitting some ridgrd insulation over them. Off course this won't work if you need the light from the windows. in that case you can add a insulating kit like some folks use inside their homes. http://www.amazon.com/Plastic-Window-Insulation-Kit-Improvements/dp/B005OQCU9E of course the best way is to have your door replace with a new insulated door if your budget allows.
 
#9 ·
There will be leaks, but I have to say the foam (polystyrene) insulation from home depot works really well on the inside of an non insulated garage door as a radiant barrier. Here in Arizona, with the garage facing west, it would get to the point where it was literally burning to the touch on the inside and the door acted as a giant radiator.

Even though the whole garage was terribly hot this summer, you could feel even more heat as you got closer to the door. The foam insulation made a huge difference at that level, and I assume it would make a difference for cold as well even though it's not the same as dealing with the sun beating on the door all day. The one I got has an aluminium facing on one side (that goes against the door) and is 1.5" thick. The other side is littered with blue branding and lettering, but I covered that with white paint.
 
#10 ·
I don't know where you live but here in North Carolina it does get cold out. I have one of those tortches that hook up to a gas grill cylinder. It heats up my shop pretty quick I just turn it on about 20 min before I go in there. I never really have had an issue with condensation on my tools using it.

As for the door use the foam insulation and just cut to size (I am sure someone else already said that)

Cheers
 
#11 ·
It will cost a little more but the Isocyanurate foam with the alluminum coating igives you a better r value in a thinner sheet and the surface is reflective as well. this helps in lighting the area. It is possible to insulat the door you have with a kit from Owens corning or make your own. cut the panels to fit the voids in the door and foam them in place. Tape the area you do not want the foam sticking to first and then just strip it off. Or what I did was wax the exposed back surface of the door and tape the edges so the foam didnt squirt out the holes and it cleaned up great! Adjust the hinges for a proper seal on the outside.
 
#12 · (Edited by Moderator)
I ordered my 8×16ft Overhead Door with 1in insulation + Steel plate backing in all panels, for a near bullet proof security solution. It also insulates rather well, though I do need to add some more 1in foam insulation tape along the top of the door frame where I do get "some" air leak. The rest of the garage has the 1/4in Radiant Heat Barrier solar/fiberglass sheeting R5/R10. That truly is all I need in South Texas. I also have an 8ft closeable vent in the gable. In the winter I can heat the garage with a 1000w baseboard heater and get it up to 65F within a couple of hours.

Below, you can see the interior of the garage door in the left portion of the photo.
Table Wood Workbench Floor Flooring
 

Attachments

#13 ·
There are a lot of variables here that I don't have time to cover, but you're in luck because I do home energy analysis every day as a course of my business. Your number one enemy is air infiltration. All the insulation in the world makes no difference if there are air leaks. Install door seals on the garage door and ensure they seal tight all around. Look for other leaks around side doors, hose outlets, and windows. In a previous house I used the garage insulating panels that are pre cut to fit and regretted it. I would look at Dow Thermax foam. Try to find 1.5" thick foil faced and install it in the door with the foil on the exposed side.
 
#14 ·
For many years I have used an unvented propane heater and have not noticed any condensation on the tools. I will turn it on about an hour before I want to do woodworking and it will raise the temperature about 20 degrees. With the insulation in my shop (part is walls and ceiling R11 and the rest R-19) I don't seem to have many problems. I live in St. Louis.
 
#15 ·
I covered my steel garage door with 2" polystyrene and then a layer of silver "Reflectix" insulation. I also insulated the walls and attic and vapour barriered them. I'm able to keep the shop above freezing in -30 temps with a 5000 watt heater. Stopping the freeze/thaw cycle makes it a lot easier to keep rust at bay!
 
#16 · (Edited by Moderator)
Motor vehicle Automotive design Vehicle Houseplant Gas


Thanks for all the comments and suggestions. My garage is part of the house which explains why the walls and ceiling are all insulated. I cannot help but feel envious when I see spacious workshops like HorizontalMike's! I don't have enough room to swing a cat - I've attached a picture of mine for comparison. I will try the insulation on the door panels as it is not a big expense. I am still worried about heat loss around the door seals but will see if there are better quality replacement weather strips. I like natural light in the shop so will definitely retain the glass windows. In the future I will look into double glazed units but will try the plastic window insulation kit for the time being. Agallant and Jessetut, I have seen the propane heaters but don't they need to be vented?
 

Attachments

#18 ·
"...Some don't need vents…."

Yeah, that is probably just a southern thing for the summer. Here is south Texas that vent and opening the 8'x16' garage door, keeps things in the low 100s and very close to ambient. With the vent closed temps soar 10-20F higher inside the building if it has been closed up during the day. That really shortens the life of my stains, finishes, and glue.
 
#19 ·
If you don't use the garage for storing cars and that slab gets cold, you could lay some 1 bys on the ground and place the thicker sheets or rigid foam between them and then cover with 3/4 ply.

How you prep the area will depend on how much water comes up through your slab though. The radiant effect from the cool slab would be severely reduced. Couple with the insulated and properly weatherstripped doors, you gain a lot from a heat transfer perspective.

Also, I recommend that if you want it to be extra warm in the winter and really cool in the summer, that you let me store the Duc for you. This has been proven… by science… to do both of those.

Claims of warmer winters and cooler summers by storing Ducatis at Doss's residence provided by Doss are backed by Doss simply saying they are backed by science. To date, no studies or tests have been conducted to prove or debunk such claims. Doss takes no responsibility in mileage increases due to the complex nature of his storage procedures
 
#20 ·
Doss, you bring up an excellent point about insulating the concrete slab. I cannot do anything about that anytime soon but maybe in the future. By the way, thanks for the offer of storing my 996 - I will think about this very seriously.
 
#21 ·
Dealing with the same thing here in Eastern Canada where the temperature is dropping. Our garage is insulated, but the door is old and needs to be replaced.

I just sprang for an electrician to wire a 220 outlet in my garage so I could hang a garage heater from the wall. He also installed a thermostat that I can reach by just opening the door from the kitchen. I can leave the thermostat just above freezing unless I'm going to be doing work. Then I can turn it to whatever and let it warm up.

I also have a small ceramic heater on my work desk because it's around the corner from the heater. I'm paranoid about leaving it on, so it stays unplugged unless I'm next to it.

Next step is a new garage door. About 1200, plus the opener, plus, plus plus…. will have to wait and see on that.


 
This is an older thread, you may not receive a response, and could be reviving an old thread. Please consider creating a new thread.
Top