I need to butt-joint two pieces of plywood with glue and screws. Will plywood tolerate having a screw driven into its edge (even with a pilot hole), or will the plywood split? What about butt-jointing normal wood, with the screw driven into end grain? How well will that hold up?
I guess I am not sure if you are screwing it on the face, or the edges. I use a pocket hole jig for 3/4 ply. It seems to work fine. I havent tried to glue ply thinner than that though.
I have used butt joints, with screws going into the edge of plywood many times on shop furniture, jigs, etc., and they work perfectly fine. However, I would not use that type of joint to support a great deal of weight, such as a shelf for a planer, unless the overall structure included some other type of reinforcement. I'd give pretty much the same advice for solid wood as well.
Multiple offset biscuit joints in a "saw tooth" pattern. Or if you have the room and your biscuit jointer blade is SUPER sharp stack two at each position with the width of a biscuit between each one. The "side grain" of the plys will glue OK, it's the end grain where the issue lies.
I'm not too knowledgeable when it comes to plywood, so I have to ask…
Is the "side grain" of the plywood the edge of the plywood that is running parallel to the grain (typically the 8' sides on 4×8?) That's my guess, but was just making sure…
I don't think you are ever going to get a real strong joint when you put 2 pieces of plywood together. However, in some applications a real strong joint is not needed.
If I wanted a strong joint with plywood, I would run both pieces into a groove in a corner piece of solid lumber.
The diagram below shows a rough picture (it's a jig for sharpening chisels on a bench grinder). The bottom and side pieces are either plywood or real wood. The gray thing across the top is threaded rod. There are other parts, but I've left them out.
If I use plywood for the two uprights, I'll need to drive screws up through the base into the edges of the plywood. I can use real wood if plywood won't work. In either case, I can probably cut some dados for the bases of the uprights to give them more stability.
Or, maybe I should mount the uprights on the sides of the base and drive the screws horizontally through uprights into the base:
The base is a big slab of 2"x12" pine, so this design would require driving screws into the end grain of the base.
Brett, I would go with option #2 above, but take it a step further and rout a very shallow 1/16" rabbet on the end pieces. Not for additional strength, but to make assembly easier. With plain butt joints, things like to slip around when glue and clamps are applied.
Predrill for the screws, glue it up and everything will work great. Just use long thick screws.
If you go with option 1, I'd definitely bring the ends in about 1/2" each and cut 3/8" or even 3/4" dadoes since you're using 2×12" pine.
NiteWalker, if I go with option 2, should the rabbets in the end pieces be made where the base touches the end pieces? (Sorry for the beginner-level question.)
I thought you were talking about a true butt joint, two pieces of plywood butted end to end.
The right angle connection you are planning should be fine.
If you need extra holding power for that joint you can put a large (3/4" to 1") dowel through the "end-grain" piece in the path of the screw and about an inch away from the end. That makes a very strong joint.
I believe I'd go with your first example and make the base piece about an extra 1" long so the screws would not be so close to the edge.
Plywood screwed through the edge doesn't perform as well
as most solid wood in screwholding, especially near the edges
where the plywood can split if the joint is stressed.
Confirmat screws offer the best performance in this sort
of application. The holes are best drilled with a special
bit.
This is an older thread, you may not receive a response, and could be reviving an old thread. Please consider creating a new thread.
Related Threads
?
?
?
?
?
LumberJocks Woodworking Forum
2.5M posts
96K members
Since 2006
A forum community dedicated to professional woodworkers and enthusiasts. Come join the discussion about shop safety, wood, carpentry, lumber, finishing, tools, machinery, woodworking related topics, styles, scales, reviews, accessories, classifieds, and more!