LumberJocks Woodworking Forum banner

Moving to a new shop! Maybe a third of the size though!!! Smart?

3K views 29 replies 17 participants last post by  Lochlainn1066 
#1 · (Edited by Moderator)
I am thinking of moving my shop home for a few reasons.

Current location isn't that great- I have had one break-in where I had the following tools stolen: framing nailer, roofing nailer, cordless drill, box of assorted Kreg screws, brad nailer, RO sander, respirator. This was about a year and half ago. It is located about 20 minutes from the house so that is a bit of a pain to have to drive to the shop, just thinking of a shop to hang out in at the house would be awsome!

The downside is that the shop is a great deal smaller. I will be going from a 35×40 building dedicated to only my woodworking shop to a 13.5'x25' room in our "boat barn". That is much smaller, but I have gotten on Grizzly's workshop planner and messed around with my tools and they can fit pretty easily in there with room to spare.

I will have to following large tools in the 13.5×25' space- Grizzly cabinet saw, 8" jointer, router table. Those are the tools I currently have but I plan on adding a bandsaw and a floor drill-press, also I will be building a mobile miter saw station that will have folding wings like the many great ones here on Lumberjocks.

I do not plan on storing my sheet goods in the small space but somewhere else in the barn. I will more than likely have a small luber rack for some materials in the shop though.

The good part that I see about this move, other than it being at home is that I will be starting from a clean state, bare stud walls with a garage door on one 13.5' end and a double door on one of the 25' sides. It has a 9' ceiling with the ceiling joists exposed. The roof has all attic trusses so I have a bit of a loft but I do not have access to it very easily, only through a 2' by 20' opening between the wall and the first truss. Slab foundation.

So what I am wondering is, is this a smart move? Starting with a clean, albeit small, slate would be a wonderful opportunity.

I am a person who likes a neat shop where everything has it's place and is in it's place.
 
See less See more
#2 ·
Heck, if I had a 13.5'x25' shop I'd feel like a BB in a box car!

My shop is in half of a two-car garage … and co-exists with two cars in the garage every night!

-Gerry
 
#3 ·
i think its a smart move…i think we get to thinking that when were in a large area that we cant do it with less…and i think that is wrong..i think with the tools you have with the proper planning you can have a shop that will easily work for you…if your paying for the space your in now…that means that will be money saved…in fact if i were you , i would use the saved money to expand some and improve the new space…make sure you can stay warm and cool when needed…if you need insulation …then do it…if you make your living from this…you have to have a warm place…my shop is 20×30 and its more then enough to work in…and mine is for pleasure only…good luck with your move…i would do it…and now having to drive to work…gas money saved…would it effect your customer base…if not…its an easy decision …give us pictures…we love pictures
 
#4 · (Edited by Moderator)
well well sailor…i just looked at your home page and see your in dothan…im in a little town called verbena which is at mile post 200 on I65…if your ever this way your more them welcome to stop on by…ive got back problems and don't travel much , but if i did i would love to stop and see your new shop…but come on by if your this way…i could always use a visit with another wood worker….grizzman
 
#5 ·
I moved from a 50' x 50' building into a 16×24 car shed that I rent. I kept a few too many tools, so space is to tight. I have had to re-think some of the storage ideas i use. Everything I have is portable, movable.My lumber is in a storage shed that I built outside the workshop (not ideal but works). You say you like to be organized and everything in its place. Allow enough space to continue doing this, then you won't get overwhelmed ! I used to drive 45 minutes, I like my little shop at home now. Best of luck !
 
#6 · (Edited by Moderator)
You do not say if you are renting the bigger building or what you are going to do with it if you own it? Is this a business or a hobby shop? What do you mostly build? I have a 14 X 21 shop and with a little planning you can get a lot of equipment in a shop that size. Most equipment has to be mobile and you need to pull out the pieces you are going to use. Take a look at my shop, you might be surprised how much equipment I have in that space. I do have a shed just out side the back door to hold off-fall, jigs and misc. I store some lumber in the basement and can finish down there if I want. I mostly build projects for friends, church and family. I am doing woodworking because I want to and not that I have to. I am retired, Thank God!

I had a 16 X 24 shop when I had my business for 9 years in ND. All my older project pictures show you the different things I made in that shop with a lot less equipment than I have now. I had a 10"unisaw, power miter box saw, 14" bandsaw, power hand tools and hand tools. Yes you can do woodworking out of a smaller shop. You mostly lose production time. Looking forward to seeing your new shop, if you decide to go that way. Putting a new shop in is a lot of fun and it is nice to be close to home.
 
#7 ·
I only have a 12X24 sized shop. You could look at the photos of my shop on here, but those photos are a little out of date and with all of the clutter, it might discourage you. The key with a small shop is organization. I am constantly coming up with ideas of how to organize things better. You'll figure it out. Be sure and post photos of the new shop for us. On another site that I participate on, we have a saying, "without pictures - it didn't really happen."

Doc
 
#8 ·
regardless of the shop size
(i've had to many to count)
everyone gives it's own 'flavor'
to the work environment

and give you the opportunity
to learn newer and different ways of doing things

with your sailor mentality

'a place for everything
and everything in it's place'

will bring things forward
you may never have thought of
in a larger shop

that it is home is a plus

you can work in your underwear !
 
#9 · (Edited by Moderator)
You'll have about 340 square feet. I have 400 square feet and I have ever tool you have or plan to get plus lathe, planner, mortising machine, dust collector and grinder. For me it is quite doable if I stay organized and build in good storage.

IF you think out your floor plan carefully this should be doable for you also.
 
#11 · (Edited by Moderator)
First off, thank you all for the great replies. I believe I will make the move.

To answer a few questions
- I do not rent my current shop. My family owns a few building in town and it is one of them
- It is more of a hobby shop than a business. Although I do comissions from time to time.
- I mostly build medim sized projects with a few larger ones. Medium being an adirondak chair.

I was going to ask about insulating the shop. It was suggested that I do so. I do not plan on cooling the shop but I will be trying to keep it somewhat warm in the winter.

I am thinking 1/2" ply for the walls and I would like to paint it a bright color. White? Grey? Tan? What is a good shop color to brighten the place up and make it look larger.

I do plan on putting all tools on wheels except for my table saw.

Thank you all. I will probably be doing some sort of video journals on the whole process.
 
#12 · (Edited by Moderator)
wal-mary has 5 gal of 'hide all' paint
for $50
it comes in
flat
semi-gloss (washes better)
white and off white
interior or exterior
goes on great
and is cheap

and yes insulation works in both directions
cool in summer
and warm in winter
 
#13 ·
Now that I have read your responses to my questions, I would say, Go Boy Go!!! The better you insullate the easier it is to heat or cool. It takes less time to do either and it holds the temperature longer. I always used white on all my shop walls. There is never too much light in a shop. Do not skimp on lighting and plug ins. Looking forward to seeing your progress.

Tom
 
#14 ·
I would think anyplace you have would be a great place. If you need more space, PVC pipe and a tarp cover would work when the temp is good. If you need any assistance drop me a note.
 
#16 · (Edited by Moderator)
now that i know where you live i would suggest you insulate at least the ceiling…but if you can i would do it all while your doing it…i live in mid state Alabama and have had my shop for 15 years now…with no insulation, and boy its been a fight to get it warm on cold days..and it took lots of wood to keep it that way, well i just got done insulating the ceiling last week with my son…and its made all the difference in the world…i run a wood stove and it will now run me out if i run it to hot…if you want to heat for cheap…i would have a small wood stove…but there are many options for heat…but i suggest it because you can get your own wood and not have money going out the door for your heat…good luck with your decision to move..tom suggested white…i agree…being in a man cave doesn't mean it has to be dark and dingy…bright and good lighting…ive got a total of 12 4 tube florescent lights in mine and over with my bench i have more lighting to really light things up…good luck..
 
#17 ·
Ok, looks like I will insulate it completely and paint it a nice bright white. I will have to check out my plug situation first, luckily 220 is already run to my little bay so I may just have to move it.

Thank you all for your great suggestions.

As I type, the bay is pretty over run with things. For one, a bass boat that will be moved, but also alot of other junk that my step dad decide he had some reason to keep although I can't figure that reason out for the life of me. Hopefully tomorrow I can get him out there with me to clear some junk out.

I will keep you all updated, what would be.the best way to do that? Blog? This thread? Something else?
 
#18 ·
As much as I dream of having a big 1000 ft^2 or larger work area, it would just mean that I'd have to work harder to organize it. At 400 ft^2, your typical garage with space left over for the wife to park a car, I seem to have all the space I need once I evict the car and utilize a couple of rolling carts. At least that's true of the actual milling and woodworking itself.

The only time I wish I had a bigger space is when finishing a project….or for long-term assembly and storage of a project. I'd love to have an extra finishing room and larger assembly area when I don't have to worry about finishing a project in order to reclaim the space. But I figure that if I had an additional garage bay (another 200 ft^2), it would suffice.

Perhaps if my tools were larger, I'd have a true need for more space. So, for me in my hobby workshop, 600 ft^2 would be optimum, 800 to 1000 ft^2 ideal, and anything bigger a more costly luxury.

Aside: Garages often hold more than just woodworking stuff. If I could get rid of everything that doesn't belong, I KNOW it'd be enough space. So, if it's an out-building on the property where you don't need to store automotive stuff, kids toys, and the occasional miscellaneous box, then I'd say you'd be good to go, especially if you can refit it from the ground-up.
 
#19 ·
Cosmic-
I like your thinking, an extra finishing room would be very nice. My current shop has one that is closed off from all the sawdust I must say I am going to miss that for sure.

I am fortunate however that only my stuff will be in my shop, no other unnecissary items. Everything will be woodworking related other than two medium sized toolboxes with mechanic tools in them.
 
#20 ·
Sailor, I would rethink the plywood on the walls. I have a 24' by 32' shop and used white pegboard on 3 of the 4 walls and love it. You can buy pegboard hooks in bulk and hang everything up. And rearranging it is easy. I have so much "stuff" hung up now that I've run out of pegboard!
 
#21 ·
Uncle Fester
You know I have some pegboard in my shop now and I can never get it to work just right for me. For some reason, the hooks are always falling out and just not cooperating with me. Not sure why, but it has made me stray away from pegboard for a while. But if I decide to try it again I can simply put it over the plywood with a space between the two.

Thanks for the suggestion, I may find a time when pegboard is just what I need.
 
#22 · (Edited by Moderator)
try 'french cleats'
they can hold anything
and can be re-arranged as needed
two or three courses
up and down the wall

it has always taken me 6 months
to keep moving things around
until they find their best place
(something i can never anticipate)
 
#24 ·
While I also have been drooling over getting a floor model drill press, I have managed to get by with my ~18yr old 8" bench top drill press by anchoring it to the bench with clamps. Forget that mine, in the attached image, is an 8" model and consider that you could store a nicer/larger bench top model (with a 3.25" spindle travel and maybe radial movement) in a cubbyhole until needed and then bring it out for use. This might help save that precious floor space for other things.

Just a thought…
 
#25 · (Edited by Moderator)
I have a 600 sq. ft. shop. It's shaped in an "L". Everything I have is on wheels. It's a pain. I'm looking foward to a 1200 sq. ft. shop in a new home. I would love to be able to walk from my jointer to my table saw without moving anything. I have a contractor saw, miter saw, radial arm saw, Delta 14 in. bandsaw, Shopsmith, 15 in. Powermatic plane (Bendex head, my new baby), 6 in. jointer, router table, floor buffer, grinder, Powermatic jig saw, scroll saw, midi & full size lathes, belt & disc sander, drum sander, ocalating spindle sander & every portable tool known to mortal man crammed in here. Needless to say IT'S TIGHT! Oh! I forgot my Shopsmith bandsaw & strip sander waiting on standalone stands. I don't understand downsizing, but the theft of equipment could make a quick change in my thinking.

My walls are pegboard, but I don't use peg board hooks, I painted the shop bright yellow. It's bright & cheerful.

Pop
 
#26 ·
Jim: My father did his shop entirely in pegboard, though he made the mistake of putting the brown side out. I guess he thought it was more manly that way…it's too dark as a result.

Still, I love the idea and will likely do two walls that way myself since at some point soon I'll need to remove some drywall to re-wire my garage shop anyway.
 
This is an older thread, you may not receive a response, and could be reviving an old thread. Please consider creating a new thread.
Top