I'm an entrepreneur who does woodworking for a hobby (I love to save money!). I keep stacks of used paper and currently use a heavy duty paper trimmer to cut stacks of paper into quarters then bind the edges with glue to use as notepads - the office loves them.
I recently picked up a 13-amp Delta table saw (I love it!) and am curious if my saw could cut stacks of paper. I don't know how a stack of paper compares density wise to wood and I don't want to blow something up…
I think you're looking for trouble here but I suppose if you could figure out some way of securely clamping the stack to a sled of some sort is possible.
I wouldn't try it. The saw will likely cut it just well, the edges will be fairly rough but the bigger problem will be controlling the paper for the cut. Unless you find a way to secure it to a sled that will be very tough to do. If you insist on cutting it on a saw, try a bandsaw.
You probably can do it using a jig that resemble a flower/wine press. It has to be longer than the size of the paper so the saw doesn't completely cut the bottom in half and barely touch the bottom of the press plate.
Paper is quite dense and should be perfectly fine to cut on the saw if suitable supported, for instance on a zero clearance sled.
Let us know if you succeed!
Yes you can cut paper on your table saw using a fine blade. Take a stack about as thick as you can go and use packing tap to bind the bundle then cut through it. I haven't done this in years but if I remember correctly the majority of the paper is cut good. Also if you have a scroll saw bind up your little pads the same way drill a small hole insert the blade and you can cut out little pictures or monograms. And for everyone's information you can cut cardboard quite well, cut plexiglass and even aluminum and brass sheet with the right blades.
I buy my shop towels in huge rolls that I cut down. I use my bandsaw, and have enough trouble doing that. It tends to clog the blade and shorten the lifespan.
I would not even think about putting paper through my table saw. A ream of paper will get caught, dragged down, who knows what happens then…
Band saw should cut it well. I cut cardboard on my bandsaw because i never have a box cutter to cut up a box in my garage for recycling. It might dull my blade a bit bit i buy cheap blades already.
I think it can be done if you sandwich the stacks of paper, tightly between 2 sheets of plywood. They also make special knife cutting blades. I think Tenyru makes some.
two sheets of ply clamping the paper. ride on the fence. sounds good to me. will have rough edges. You can buy a paper cutter. A tool for every job. Hence why I chop onions with my knife and not my table saw.
If you have a heavy duty paper trimmer already why not stick with that? You get nice clean edges with that - you'll certainly have a ragged mess with a table saw.
I think it can be done if you sandwich the stacks of paper, tightly between 2 sheets of plywood. They also make special knife cutting blades. I think Tenyru makes some.
Wow… This is one hell of a community - I'm blown away by all the responses!
I have quite a bit of paper so my paper slicer will take too long. I think I'm going to build a MDF sled that will allow me to sandwich a stack of paper and tighten it down as needed. Then I'm going to take it oh so very slowly. It's still just scratch paper so if it shreds and makes a mess then it's not the end of the world!
I'll do my best to document it all, but I'm backed up at work so it may not happen right away.
I'm currenty using a 50T Diablo multi-purpose. Anyone see any issues with me using that blade? I don't want to go buy a new blade just for this if I don't need to.
By heavy duty paper cutter, do you mean a stack cutter?
Because if you have one of those, I fail to see how the table saw would be faster or better. They are super quick and easy to adjust and use. Remember that paper and cardboard are also hard on saw blades.
Congratulations on being an entrepreneur. Great job on saving money (I hope you are taking the amount saved and investing it for retirement). I have been doing the home-made notepad thing for about 30 years - when I started my co-workers made fun of me but they all used my notepads, and when I left for another job they complained that they had to start buying notepads from the office supply store.
Now about your question: Google "how to make a book box" instructions on how to cut the pages out of an old book to make a secret compartment box. There are videos that show you how to sandwich the paper pages between cardboard or thin pieces of wood so you can use power saws to cut the paper, leaving a nice clean edge. You should be able to adapt the technique to your situation. Good luck and let us know how it goes.
By heavy duty paper cutter, do you mean a stack cutter?
Because if you have one of those, I fail to see how the table saw would be faster or better. They are super quick and easy to adjust and use. Remember that paper and cardboard are also hard on saw blades.
Congratulations on being an entrepreneur. Great job on saving money (I hope you are taking the amount saved and investing it for retirement). I have been doing the home-made notepad thing for about 30 years - when I started my co-workers made fun of me but they all used my notepads, and when I left for another job they complained that they had to start buying notepads from the office supply store.
Now about your question: Google "how to make a book box" instructions on how to cut the pages out of an old book to make a secret compartment box. There are videos that show you how to sandwich the paper pages between cardboard or thin pieces of wood so you can use power saws to cut the paper, leaving a nice clean edge. You should be able to adapt the technique to your situation. Good luck and let us know how it goes.
By heavy duty paper cutter, do you mean a stack cutter?
Because if you have one of those, I fail to see how the table saw would be faster or better. They are super quick and easy to adjust and use. Remember that paper and cardboard are also hard on saw blades.
Stack cutters are the most ingenious devices ever invented for doing small veneer projects. A quality one is like having a mini veneer guillotine in the shop and the price is way lower.
There. I just gave you an excuse to buy a new woodworking tool.
Well I hope everyone learned something from all of this. I just discovered that my Kinkos will cut a stack of 100 pages for $2 per CUT with their hydraulic cutter.
This is an older thread, you may not receive a response, and could be reviving an old thread. Please consider creating a new thread.
Related Threads
?
?
?
?
?
LumberJocks Woodworking Forum
2.5M posts
96K members
Since 2006
A forum community dedicated to professional woodworkers and enthusiasts. Come join the discussion about shop safety, wood, carpentry, lumber, finishing, tools, machinery, woodworking related topics, styles, scales, reviews, accessories, classifieds, and more!