LumberJocks Woodworking Forum banner

Any opinions on moisture meters?

9K views 20 replies 13 participants last post by  douglbe 
#1 · (Edited by Moderator)
Hey All,

I was looking into getting a moisture meter and was wondering if anyone here had any experience with them.

I would like to avoid the pin type.

Any thougnts?

Gary
 
#3 · (Edited by Moderator)
I have a Wagners Pin-less (Not found since the move from NJ) and so I bought a Lignomat. Because I didn't figure that I needed two of the same if I found the first one.

They both seem to work great. I can't say about the accuracy between them because I can't use them on the same board, because I can't find one.

Mark Decou and I worked on a blog that Mark started. You might look there also.
 
#4 ·
I am also very interested in opinions on moisture meters. I see prices from $25 to well over $120. my usual rule is "bigger is better" and "you get what you pay for" but those rules have failed me in the past :) not often but enough times so that I want to do my research.
 
#5 ·
Well, it doesn't look like anyone has really used on here with the exception of Karson.

It looks like at this point I have decided on the Wagner L609. It's cheaper than the Wagner MMC220
which has a wider range, and more precision, but at $100 more.

Wagner L609 - 4% to 22% $149

(Amazon)

Wagner MMC220 - 5-to 30% $249

(Amazon)

Anything above 22% I'm not going to deal with anyway, and that extra decimal point won't help that much either. It's only a half a percent difference between the two.

6.4% would equal 6% and
6.6% would euqal 7% on the L609

I'll let you know.

Gary
 
#6 ·
Well, I received my new meter today, and have returned it already.

Very inconsistent readings. I spent about an hour testing it. The readings were just all over the place even re-testing the same piece after a while.

The last straw is when I measured a couple pieces of maple from on old bowling alley lane, and it said it had 16% moisture. Probably kiln dried 20 some years ago, and air drying the rest. No way it's going to suck up
to the 16% level.

Not worth even $25.

Gary
 
#10 ·
Mike - I have given up after my disappointment with my last purchase. I have gone all these years without one
I guess I can go longer.

They all seem to be calibrated for douglas fir and you have to adjust the number given for whatever wood
you are testing. That means either you need a really good memory or use the pamplet with the conversions.

Gary
 
#12 ·
All I know is that if ya whack it with a hammer, and it spits back at ya…well, if it's wood, then it's too wet. If it ain't wood, then it's still alive and you've really pissed it off!

Hahahahahahaha! Sorry Gary…my bad. Had to say it. The temptation, ya know?
 
#15 · (Edited by Moderator)
Buy cheap. I think there is a saying in there someplace.

I've got the Ligonmat and I'm happy with it. It uses wood density and moisture to figure out the % moisture. If you hit a knot the readings change.

I still haven't found my Wagner pinless one. so no comparison between them.
 
#16 ·
dang Karson I was hoping when you found it you'd offer to sell one cheap…. ????
I'm a bit surprised that there wasn't more input on this. My wife is looking into one of these and I'm quite ignorant about them. I know people use them who/whom I still can't say
Gary I am curious why the choice to avoid the pin type?
need to rummage in the piles of Wood magazine and see if they have an article on these. Something's ringing a bell - either that its the echo again…
 
#17 ·
I finally decided to pick up a Delmhorst J-2000. Amazon has them for $187. Not exactly cheap, but no the most expensive one either. I did a few test readings and it seemed consistent. I'll write a review after I have ran it through its paces.

Woodworking Magazine reviewed moisture meter awhile back, I can't remember which issue it was. I'll have to go back and look.
 
#18 ·
I just searched eh site to find anything about moisture meteres. This is all I found. i have a Sonin combination meter that is suposed to be a combination moisture meter, stud finder, power line locator and metal finder. It doesn't seem to do much of anything. I contacted the company, basically, they don't care. Save your bucks. Tap the wall or use a cow magnet to find studs and metal in walls.
 
#21 ·
I have the Lignomat E/D, it has pins, but I am very happy with it. Accuracy? I haven't checked with another meter, but it is consistant. I just bought some kiln dried rough sawn Red Oak and they measured 6-8% mc. right where it should be. I bought mine on Ebay for $70 (including shipping) and that to me is a great deal, this unit is in excellent condition and works great.
 
This is an older thread, you may not receive a response, and could be reviving an old thread. Please consider creating a new thread.
Top