LumberJocks

Dovetailed Router Plane Box

  • Advertise with us
Project by Tony Strupulis posted 12-02-2013 07:22 PM 916 views 0 times favorited 6 comments Add to Favorites Watch

Once a year the Alaska Creative Woodworkers Association hosts a weekend event called Tools and Techniques. As president of the club, even I am not immune to doing demonstrations! I was asked to demonstrate cutting dovetails with a router jig.

I built this box as the completed sample to show while I did my demonstration. It also helped me get all the dovetails laid out ahead of time. I sized the box to use some of the odds and ends I had kicking around the shop. With a little fine tuning, it fits my Lee Valley router plane nicely. The plane is held in the box with some machine screws that go through the fence holes in the plane body. At some point I will make some long custom hold down nuts so you don’t have to reach all the way to the bottom of the box. Look for that project some time in the future!

The sides are maple which was left over from another box project. The left side has some interesting grain patterns and color from either a knot or a branch crotch. The top and bottom panels are 1/2” cherry veneer plywood. There is a little bit of curl in the panel I put on the lid. The finish is rattle can gloss lacquer. I knocked the gloss back with steel wool and wax. I used Brusso hinges and a jewelry box hasp from Home Depot. I wasn’t thrilled about the hasp in the beginning, but I think it looks good.

I cut the dovetails with my 24” Porter-Cable Omni Jig. I used the narrow pin router bit. All of the pins were the same size, except for the half pin at the joint of the lid and box. I made that pin 1/8” wider to account for the saw kerf when I cut the top off. To make it 1/8” wider, I used a drill bit as a spacer when I set up the guide fingers. Much easier than measuring! When I cut the lid off, I put a 1/16” thick 7-1/4” framing saw blade in my table saw. That left me a little meat to true up the join. I used sand paper glued to a granite slab and flattened the box like you would true the bed of a hand plane – figure eight pattern.

Since this was my display box, I have the twin box that I built during my demonstration. I haven’t cut the top off that one yet. Perhaps I will finish it as a gift with Christmas coming up soon.

-- Tony - http://ravensedgetoolworks.com





6 comments so far

View DanielP's profile

DanielP

210 posts in 640 days


#1 posted 12-02-2013 11:30 PM

Great looking box.

DanP

-- Dan P.

View dnick's profile

dnick

952 posts in 1130 days


#2 posted 12-03-2013 04:26 AM

Beautiful piece. Well done.

-- dnick, North Hollywood, Ca.

View aussiedave's profile

aussiedave

3014 posts in 572 days


#3 posted 12-03-2013 10:43 AM

A very nice box Tony and a safe place to keep your router plane…nicely done.

-- Dave.......Keep calm and make more sawdust....

View Tony Strupulis's profile

Tony Strupulis

240 posts in 1871 days


#4 posted 12-03-2013 04:16 PM

Thanks to all.

-- Tony - http://ravensedgetoolworks.com

View Boxguy's profile

Boxguy

1539 posts in 1016 days


#5 posted 12-04-2013 05:25 PM

Tony, nice work, lovely wood. This is a very utilitarian box and serves a real purpose. You might consider making a form for the bottom of the box to cradle your plane and protect the blade. I have had good luck with carving Styrofoam and covering it with cloth. Doing something with the top to hold the plane down and in place might also help.

Cutting off the top suggestions. That second box will make a nice Christmas project. Keep boxing and keep posting.

-- Big Al in IN

View mafe's profile

mafe

9671 posts in 1837 days


#6 posted 12-08-2013 09:28 PM

I think the box is even more beautiful than the tool!
Lovely box, lovely work.
Best thoughts,
Mads

-- Mad F, the fanatical rhykenologist and vintage architect. Democraticwoodworking.

Have your say...

You must be signed in to post the comments.

DISCLAIMER: Any posts on LJ are posted by individuals acting in their own right and do not necessarily reflect the views of LJ. LJ will not be held liable for the actions of any user.

Latest Projects | Latest Blog Entries | Latest Forum Topics

HomeRefurbers.com

Latest Projects | Latest Blog Entries | Latest Forum Topics

GardenTenders.com :: gardening showcase