LumberJocks

Drill Press Table w/Micro-Adjust stops.

  • Advertise with us
Project by AdrianM posted 03-30-2013 07:14 PM 6879 views 55 times favorited 17 comments Add to Favorites Watch

Large Drill press Table 36×18 1”Thick MDF
Walnut fence and trim. Fence has graduated Inch and half inch marks etched in.
Maple micro adjust stops.
Cherry hold downs – (View my previous posts)
Offset round tear out block.
Made with CNC.





17 comments so far

View stefang's profile

stefang

13623 posts in 2078 days


#1 posted 03-30-2013 08:16 PM

Your DP table looks great Adrian. I especially like your low fence. I have always felt that most folks (me included) build them too high and have problems with the plunge handles. The hold downs on the rest look very good too. I’m wondering if the holes in the top are for clamps to anchor the table or are they just handholds to lift it off?

-- Mike, an American living in Norway.

View AdrianM's profile

AdrianM

83 posts in 1054 days


#2 posted 03-30-2013 08:30 PM

Thanks mike, holes are for f style clamps. Helps with large stock and drilling with table rotated 90 degrees. Look up Ronald Walters drill press table on google I took a lot of ideas from his version.

View hoss12992's profile (online now)

hoss12992

2955 posts in 636 days


#3 posted 03-30-2013 09:00 PM

This is reakky cool. Great job

-- The Old Rednek Workshop https://www.facebook.com/theoldrednekworkshoptn

View scrollsaw's profile

scrollsaw

13026 posts in 2597 days


#4 posted 03-30-2013 09:28 PM

Great job.

-- Todd

View gsimon's profile

gsimon

535 posts in 857 days


#5 posted 03-31-2013 12:12 AM

great project – nice pics too!

-- Greg Simon

View Robsshop's profile

Robsshop

815 posts in 1718 days


#6 posted 03-31-2013 04:47 AM

Very nice looking DP upgrade, should make all Your drilling ops much more accurate and easier to set up ! I wish I would have gone with the off set circle pads in my design, makes much more sense. I will probably adapt that feature into my DP table when I find some spare time in the shop. Thanks for sharing !

-- Rob,Gaithersburg,MD,One mans trash is another mans repurposed wood shop treasure ! ;-)

View elingeniero's profile

elingeniero

25 posts in 852 days


#7 posted 03-31-2013 05:55 AM

That’s a way nicer drill press than the one your first post sported … quill locks rock!

View Greg D's profile

Greg D

199 posts in 695 days


#8 posted 03-31-2013 07:47 AM

Great job!

-- Greg D, Cen. CA, "Keep it on the Level, Do it Right the First Time!"

View TimWood's profile

TimWood

178 posts in 985 days


#9 posted 03-31-2013 12:09 PM

You KNOW it’s a great project when you get to the end of the pictures and say “AWWW NOOOO!!! NO MORE PICTURES????” Great Job!

-- Tim Harrelson

View Matt Przybylski's profile

Matt Przybylski

468 posts in 1121 days


#10 posted 03-31-2013 02:55 PM

I too am going to be following Ronald’s design when I make my table as I think it is the best one I’ve seen yet. My question, however, is this: for the rotating insert, you’d have to still put something down over the table, it seems, when drilling wider holes (say, a 2” forstner), right? I’d imagine that would cause issue and go outside of the insert material otherwise…

-- Matt, Illinois, http://www.reintroducing.com

View AdrianM's profile

AdrianM

83 posts in 1054 days


#11 posted 03-31-2013 05:05 PM

I designed it to fit a 1 5/8 drill while still being in insert.

View AJswoodshop's profile

AJswoodshop

1057 posts in 1020 days


#12 posted 03-31-2013 06:00 PM

Great job! Here is a one I built awhile ago, they come in handy!

Dril press table-http://lumberjocks.com/projects/79676

View Philip's profile

Philip

1153 posts in 1282 days


#13 posted 04-02-2013 01:46 AM

Very nice. I like the hold-downs.

-- I never finish anyth

View whit's profile

whit

246 posts in 2720 days


#14 posted 04-02-2013 03:49 AM

Hmmm . . . looks like I have some machining to do on my existing table. Well done and thanks for the ideas.

Whit

-- Even if to be nothing more than a bad example, everything serves a purpose. cippotus

View Sigo's profile

Sigo

11 posts in 665 days


#15 posted 04-23-2013 06:26 PM

Great looking table. I’m planning my DPT and am curious how you did the tear out block in the center as well as the “plug” that occupies the space. I’ll also be wanting to use drum sanders with the table, will this offset circle setup accommodate their use? Thanks.

showing 1 through 15 of 17 comments

Have your say...

You must be signed in to post the comments.

DISCLAIMER: Any posts on LJ are posted by individuals acting in their own right and do not necessarily reflect the views of LJ. LJ will not be held liable for the actions of any user.

Latest Projects | Latest Blog Entries | Latest Forum Topics

HomeRefurbers.com

Latest Projects | Latest Blog Entries | Latest Forum Topics

GardenTenders.com :: gardening showcase